Maintenance

How to Flush a Jet Ski

Sea-Doo flushes the exhaust, Yamaha the cooling water passages, Kawasaki the cooling system. Here's where each 2026 manual puts the port, each maker's steps and run time, and what each says about salt water.

By Alex Quinn 22 min read

An uncovered sit-down jet ski on its trailer in a driveway, with a green garden hose coiled loosely on the concrete beside the stern

How to flush a jet ski depends on who built it. Sea-Doo's 2026 operator's guides flush the exhaust system, Yamaha's 2026 owner's manuals flush the cooling water passages, and Kawasaki's 2026 owner's manuals flush the cooling system. For the engine flush, the three makers agree on the order: start the engine first, then turn on the garden hose, and turn the water off before the engine stops. Discover Boating gives the general reason: starting the water flow before the engine could let water flow into the engine combustion chamber through the exhaust. Beyond that, the port, what you remove to reach it, how long the engine runs and how the last water is cleared differ by make, and sometimes by model.

This guide gives each maker's own steps, never a merged version: where each 2026 manual puts the flush port, the run times side by side, when each maker says to flush (salt water included), what each says about running the engine out of the water, and what to do once the hose is off. For the routine around the flush, see our jet ski maintenance tips.

Note

Your owner's manual has the final say

Flush ports, run times and cautions differ by make and model. The manuals quoted here are Sea-Doo's 2026 operator's guides (GTI, GTR and Wake; GTX; Spark; plus the RXT-X 325, Wake Pro and FishPro guides for run time), Yamaha's 2026 owner's manuals (VX, FX HO and SuperJet) and Kawasaki's 2026 STX 160LX/160X and Ultra 310LX owner's manuals. Older and two-stroke models aren't covered here. Where this guide and your manual differ, follow your manual.

What gets flushed on each make

The three makers flush different systems, and each gives its own reason.

Sea-Doo: the exhaust. Sea-Doo's 2026 GTI, GTR and Wake operator's guide calls the procedure Flushing the Exhaust System. It says flushing the exhaust system with fresh water is essential to neutralize the corroding effects of salt or other chemical products in the water, and that it helps remove sand, salt, shells or other particles from water jackets and hoses. BRP's winterizing article (2026) says why the engine itself isn't flushed: "Sea-Doo personal watercraft's closed-loop cooling system already contains antifreeze and does not require flushing."

Yamaha: the cooling water passages. Yamaha's 2026 owner's manuals say to flush the cooling water passages to prevent them from clogging with salt, sand or dirt. Yamaha's 2021 Maintenance Matters guide gives the background: a WaveRunner is raw-water cooled, meaning it uses the water it's operating on as cooling water, and Yamaha says all water, fresh or salt, contains contaminants that will eventually build up in the cooling passages.

Kawasaki: the cooling system. Kawasaki's 2026 STX 160 owner's manual calls the procedure Cooling System Flushing. Kawasaki says it helps prevent premature wear due to internal engine corrosion and the buildup of salt or other mineral deposits that can lead to cooling system blockage and overheating; the 2026 Ultra 310LX manual adds that it helps prolong the life of the exhaust filter. The Ultra 310LX manual also has a second flush, for the supercharged model's intercooler cooling system, and says it is not necessary to start the engine for it. Of the manuals cited here, it's the only flush done with the engine off.

Discover Boating (NMMA) puts it in general terms: on models with a closed cooling system, which it says covers most late-model Sea-Doo PWC, you flush only the exhaust; on other PWC you flush the exhaust and the engine cooling passages.

Where the flush port is, by make and model

Discover Boating, writing about PWC in general, says the flush port is on the transom on some models and under the seat or in the engine compartment on others. Each maker's 2026 manual is more specific. Here's where each one puts the connection, what it says to remove or open first, and how the hose attaches.

From each maker's 2026 manual, read 2026-10-30. Only the models named are covered; your model's manual may differ.
ModelManual citedWhere the connection isRemove or open firstHose connection
Sea-Doo GTI, GTR, Wake and GTX2026 GTI, GTR and Wake guide, pp. 161-162; 2026 GTX guide, p. 145The water inlet connector at the rear of the watercraftNo removal step before the hose goes onGarden hose to the connector; Sea-Doo recommends its flushing connector adapter, 295 500 473, when a quick connect adapter is used
Sea-Doo Spark2026 Spark guide, p. 128The connector at the rear of the watercraftNo removal step before the hose goes onA hose to the connector; the guide names the same adapter part
Yamaha VX family (VX-C, VX, VX Deluxe, VX Cruiser, VX Limited)2026 VX manual, p. 100The flushing hose connector, shown in the engine compartment under the seatsPlace the craft level and remove the seatsRemove the connector cap; push and twist the garden hose adapter in until it's secure
Yamaha FX HO and FX Cruiser HO (same steps in the FX SVHO manual)2026 FX HO manual, p. 114Not stated in the steps quoted hereRemove the seats and the removable watertight storage compartment; open the stern storage compartmentRemove the connector cap; push and twist the garden hose adapter in until it's secure
Yamaha SuperJet2026 SuperJet manual, p. 63Not stated in the steps quoted hereRemove the hoodRemove the connector cap; push and twist the garden hose adapter in until it's secure
Kawasaki STX 160LX and 160X2026 STX 160 manual, p. 188The auxiliary water supply port, under the rear seatRemove the cap; no further access steps givenGarden hose with a screw-in fitting
Kawasaki Ultra 310LX and 310LX-S2026 Ultra 310LX manual, pp. 32 and 194An engine flushing port and an intercooler flushing port, at the sternNo access steps givenGarden hose with a screw-in fitting, for both the engine port and the intercooler port

Discover Boating says some flush ports accept the male end of a garden hose while others use a snap-in adaptor that screws onto the hose, that the adaptor was supplied with the PWC when it was new, and that a dealer can supply one if your model needs it. The makers name their own: Sea-Doo's flushing connector adapter (295 500 473), Yamaha's garden hose adapter, and for Kawasaki's STX 160, a garden hose with a screw-in fitting.

Discover Boating also says you can flush the PWC on a trailer, a storage rack or a lift, but it must be out of the water. The makers' own steps are written for a craft out of the water or on land; none of them gives a procedure for a craft afloat. If yours lives at a dock, see can you leave a jet ski in the water.

Hands holding an open owner's manual beside the stern of an uncovered jet ski on a trailer

How to flush a Sea-Doo

These steps are from Sea-Doo's 2026 GTI, GTR and Wake operator's guide (pp. 161-163). The 2026 GTX guide has the same connector, run time and shutdown steps, and the 2026 Spark guide differs at step 3. Sea-Doo's guide warns that failure to flush the system, when necessary, will severely damage the exhaust system, and says to make sure the engine operates during the entire procedure. Its danger box says not to run the engine indoors or without adequate ventilation, or let exhaust fumes accumulate in confined areas.

Flush a Sea-Doo (2026 operator's guides)

  1. Step 1: Connect the hose

    Connect a garden hose to the connector at the rear of the watercraft. Don't open the water tap yet. If you use a quick connect adapter, Sea-Doo recommends its flushing connector adapter, 295 500 473.

  2. Step 2: Start the engine, then open the tap

    Start the engine, then open the water tap immediately. Sea-Doo says always to start the engine before opening the tap, and to open it right after the engine starts to prevent overheating.

  3. Step 3: Run the engine

    Run the engine 90 seconds at idle. For the Spark, Sea-Doo's 2026 Spark guide says about 20 seconds at a fast idle between 4000 and 5000 RPM. Both guides say never to run the engine longer than 2 minutes, because, Sea-Doo says, the drive line seal has no cooling when the watercraft is out of the water.

  4. Step 4: Check the flow

    Make sure water flows out of the jet pump while flushing. Sea-Doo's guide warns that certain components in the engine compartment may be very hot, and says not to touch any electrical part or the jet pump area while the engine is running.

  5. Step 5: Water off, then clear it

    Close the water tap, run the engine at 5000 RPM for 5 seconds, then stop the engine. Sea-Doo says always to close the water tap before stopping the engine.

  6. Step 6: Disconnect

    Disconnect the garden hose and the flushing connector adapter, if used. Sea-Doo's troubleshooting section lists an adapter left in the flushing connector as a cause of engine overheating.

How to flush a Yamaha WaveRunner

These steps are from Yamaha's 2026 VX owner's manual (pp. 100-101), which covers the VX-C, VX, VX Deluxe, VX Cruiser and VX Limited. Where Yamaha's 2026 FX HO and SuperJet manuals differ, the steps say so. Before you start, note the VX manual's limits: don't run the engine over 4000 r/min on land, and don't run it for more than 15 seconds without supplying water, or, Yamaha says, the engine could overheat.

Flush a Yamaha WaveRunner (2026 VX manual)

  1. Step 1: Level the craft and open it up

    Place the watercraft in a horizontal position and remove the seats. For the FX HO and FX Cruiser HO, Yamaha's 2026 FX HO manual says to remove the seats and the removable watertight storage compartment and open the stern storage compartment; for the SuperJet, the 2026 SuperJet manual says to remove the hood.

  2. Step 2: Fit the adapter

    Connect the garden hose adapter to a garden hose. Loosen and remove the flushing hose connector cap, then push and twist the adapter into the connector until it's securely connected. Connect the garden hose to a water tap.

  3. Step 3: Start the engine, then the water

    Make sure the area around the watercraft is clear, then start the engine. Immediately after it starts, turn the water supply fully on so water flows out continually from the jet thrust nozzle. The 2026 SuperJet manual says instead to turn the water on gradually until it flows out continually from the cooling water pilot outlet.

  4. Step 4: Run about 3 minutes

    Run the engine at idling speed for about 3 minutes, watching the engine condition. If the engine stops while flushing, turn the water off immediately and repeat from the engine start. Yamaha says not to supply water to the cooling water passages when the engine isn't running, because the water could flow back through the muffler into the engine, causing severe engine damage.

  5. Step 5: Water off, then clear it

    Turn the water supply off. Discharge the remaining water from the cooling water passages by alternately squeezing and releasing the throttle lever quickly for 10 to 15 seconds, then stop the engine.

  6. Step 6: Close it up

    Remove the garden hose adapter and install the flushing hose connector cap, tightening it until it stops. Reinstall the seats in their original positions. Yamaha's 2026 FX HO manual also has you close the stern storage compartment and reinstall the removable watertight storage compartment; on a SuperJet, the manual says to reinstall the hood.

How to flush a Kawasaki Jet Ski

These steps are from Kawasaki's 2026 STX 160LX/160X owner's manual (pp. 188-189). Kawasaki's 2026 Ultra 310LX manual gives the same engine flush (pp. 194-195), with its ports at the stern, plus a separate intercooler flush.

Flush a Kawasaki Jet Ski (2026 STX 160 manual)

  1. Step 1: Connect the hose

    On the STX 160, the auxiliary water supply port is under the rear seat; remove the cap and connect a garden hose with a screw-in fitting. On the Ultra 310LX, the engine flushing port is at the stern, and the manual says to connect a garden hose with a screw-in fitting on its end.

  2. Step 2: Start the engine first

    Start the engine and allow it to idle before turning on the water. Kawasaki says that if the water is turned on before the engine is running, water may flow back through the exhaust pipe and into the engine, causing severe engine damage.

  3. Step 3: Water on, to a trickle

    Immediately turn on the water and adjust the flow so a little trickle of water comes out of the bypass outlet on the right side of the hull.

  4. Step 4: Idle for several minutes

    Let the engine idle for several minutes with the water running. Kawasaki gives no exact number of minutes.

  5. Step 5: Water off, then rev

    Turn off the water and leave the engine idling. Rev the engine a few times to clear the water out of the exhaust system. Kawasaki says lack of cooling water causes overheating that will cause severe engine and exhaust system damage, and not to run the engine without cooling water flow for more than 15 seconds.

  6. Step 6: Switch off

    Switch off the engine and remove the garden hose.

Ultra 310LX: the intercooler flush

Kawasaki's 2026 Ultra 310LX owner's manual adds a flush for the intercooler cooling system: connect a garden hose with a screw-in fitting to the intercooler flushing port, then turn on the water. The manual notes that it is not necessary to start the engine for this flush. Its stern figure labels the stern eyes, the engine flushing port and the intercooler flushing port.

How long to run the engine while flushing

No single run time holds for every jet ski. The makers' figures differ, and Sea-Doo's own documents differ from each other.

From each source named, read 2026-10-27 to 2026-10-31. Follow the figure in your own model's manual.
SourceModelsRun timeEngine speed
Sea-Doo 2026 operator's guidesGTI, GTR, Wake, GTX, RXT-X 325, Wake Pro, FishPro Scout, Sport and Trophy90 seconds; never longer than 2 minutesIdle
Sea-Doo 2026 Spark guideSparkAbout 20 seconds; never longer than 2 minutesFast idle, 4000-5000 RPM
Sea-Doo on-product label (2026 GTI, GTR and Wake guide, p. 66)Supercharged engines, after each use in salt or foul water1-1/2 to 2 minutesNot stated
BRP FAQ page (undated)Sea-Doo, after salt water onlyNo more than 30 secondsNot stated
Yamaha 2026 owner's manualsAll nine 2026 U.S. manualsAbout 3 minutesIdling speed
Yamaha 2021 Maintenance Matters guideWaveRunners3 minutes after each trip; at least 3 minutes to remove salt tracesNot stated
Kawasaki 2026 owner's manualsSTX 160LX/160X and Ultra 310LXSeveral minutes (no number given)Idle

Of the eight 2026 Sea-Doo operator's guides cited here, seven say 90 seconds at idle; the Spark guide is the exception. Discover Boating's general flushing steps say: "Follow your owner's manual, instructing you to idle for 90 seconds to 3 minutes." That range doesn't include the Spark guide's about 20 seconds, and Kawasaki's manuals give no number to compare. BRP's FAQ page gives a shorter limit than Sea-Doo's guides; both positions are set out in the out-of-water section below.

How often to flush, and after salt water

Each maker sets its own triggers, and not all of them name a water type.

From each source named, read 2026-10-27 to 2026-10-31.
SourceWhen to flush
Sea-Doo 2026 GTI, GTR and Wake guide, p. 161When the craft won't be used again the same day, or before extended storage (no water type named)
Sea-Doo 2026 GTI, GTR and Wake guide, p. 168Daily when the craft is used in salt or foul water
Sea-Doo on-product label, supercharged enginesAfter each use in salt water or foul water
Yamaha 2026 owner's manualsListed under the manuals' Post-operation care heading, with no separate interval; the reason given is to keep the passages from clogging with salt, sand or dirt
Yamaha 2021 Maintenance Matters guideAfter every use, fresh water included
Kawasaki 2026 STX 160 and Ultra 310LX manualsAfter each use in salt water, per the Periodic Maintenance Chart, or whenever flow from the bypass outlet drops
Kawasaki 2026 manuals, fresh waterAfter each use in fresh water: an exhaust purge, not a flush
Discover BoatingAfter a day in salt water, or after silty or sandy conditions in fresh water

After salt water

Each maker gives its own reason for flushing after salt water. Sea-Doo's 2026 GTI, GTR and Wake guide warns that failure to perform proper care, such as rinsing the watercraft, flushing the exhaust system and anticorrosion treatment, when the watercraft is used in salt water, will result in damage to the watercraft and its components. Yamaha's 2021 Maintenance Matters guide says salt water is naturally corrosive, that any left in the cooling water passages after use "is left there to do its worst," and that salt water "can also experience crystallization when exposed to heat above 170 degrees" (the guide gives no unit), which it says causes deposits that can restrict the passages. Kawasaki's 2026 STX 160 owner's manual says flushing with fresh water after each use in salt water will help prevent build up of salt deposits and eventual cooling system blockage; the 2026 Ultra 310LX manual gives the same salt-water instruction.

The Ultra 310LX manual adds an end-of-day step that isn't part of the flush. Kawasaki says moisture drawn through the supercharger can condense after the engine is stopped and not used for prolonged periods, often forming mineral deposits that may lead to supercharger lock-up, particularly if the craft has been used in salt water, and says to oil the supercharger at the end of each day's use.

Discover Boating adds a point about the engine bay: it says a salty mist can enter the engine compartment through the ventilation system and cause corrosion on the throttle linkage, electrical connections and other components, so you want to rinse it off. Our guide to cleaning and waxing a jet ski covers that rinse.

After fresh water

Kawasaki's 2026 STX 160 owner's manual gives an exhaust purge after each use in fresh water rather than a flush: remove the craft from the water, start the engine and run it for several seconds to purge excess water from the exhaust system, revving repeatedly until water stops coming out of the exhaust at the stern. Yamaha's 2021 Maintenance Matters guide says to flush after every use, fresh water included, and Discover Boating names silty or sandy fresh water as a reason to flush.

Sea-Doo's 2026 GTI, GTR and Wake guide also has an aquatic invasive species step: after each trip, before you leave the water access, drain and flush all water from the watercraft, exhaust system, bilge and every space that can hold water. That step sits in the guide's aquatic invasive species section (p. 44), not in its flushing procedure. For water inside the hull itself, see water in a jet ski hull.

A hand holding a garden hose, rinsing the side of an uncovered jet ski hull on a trailer with a gentle stream

Can you run a jet ski out of the water?

Each maker sets a limit, and the limits differ. Here's what each says.

Yamaha. Yamaha's 2026 VX owner's manual says not to run the engine over 4000 r/min on land, and not for more than 15 seconds without supplying water, otherwise the engine could overheat. The 4000 r/min line is in eight of Yamaha's nine 2026 U.S. manuals; the 2026 SuperJet manual gives only the 15-second limit on land without water. With the hose connected, Yamaha's flush steps above apply.

Kawasaki. Kawasaki's 2026 STX 160 owner's manual says that, to prevent overheating resulting in engine and exhaust system damage, you should not run the engine with the craft out of the water for more than 15 seconds at a time, and never at maximum speed out of the water. The 2026 Ultra 310LX manual has the same notice. Kawasaki also says its flush procedure provides auxiliary cooling when the craft is out of the water, for example during an engine oil change.

Sea-Doo. Sea-Doo's 2026 operator's guides say never to run the engine without supplying water to the exhaust system when the watercraft is out of the water, and never longer than 2 minutes even while flushing, because, Sea-Doo says, the drive line seal has no cooling when the watercraft is out of the water.

BRP's FAQ page says something different. Its undated answer begins "No! Never run the motor of your watercraft out of the water," with one exception: after riding in salt water, to flush out the engine, "but make sure you don't run the motor for more than 30 seconds!" The FAQ gives its reason: the cooling liquid is cooled as it passes through internal channels in the ride plate, the rectangular metal plate covering the jet pump, and BRP says that plate needs to be submerged to dissipate heat and keep the engine's cooling supply below a specific temperature. That sits beside Sea-Doo's 2026 operator's guides (90 seconds at idle, about 20 seconds on the Spark, with a 2-minute cap) and BRP's winterizing article (2026), which says to let water flow at idle for about 90 seconds, then turn off the water first and stop the engine. This guide doesn't pick between BRP's documents: follow the operator's guide for your own model.

Important

Hot ride plate

Sea-Doo's 2026 GTI, GTR and Wake guide warns that when the engine runs with the watercraft out of the water, the heat exchanger in the ride plate may become very hot; avoid any contact with the ride plate, as burns may occur. Sea-Doo's 2026 Spark guide gives the same warning for the heat exchanger.

After the flush

Each maker's steps end with a few closing jobs.

Before you walk away

Flushing isn't the storage drain. Sea-Doo's 2026 GTI, GTR and Wake guide says that in areas where temperatures may freeze, water trapped in the exhaust system and intercooler must be removed, using pressurized air through the flushing connector. The full storage steps are in our winterizing guides: how to winterize a jet ski, plus the maker guides for Sea-Doo, Yamaha WaveRunner and Kawasaki. Antifreeze questions are answered there; none of the 2026 flushing sections cited here includes an antifreeze step. For the start of the season, see getting your jet ski ready for summer.

Covering the craft after the flush

A cover doesn't replace the flush; the makers' steps above still apply whenever they call for them. Once the flush is done, put the cover on a clean, dry craft whose exhaust has cooled; see how to put on a jet ski cover.

Our Weatherproof Shield is a water-resistant cover sold as trailerable. The supplier's spec lists 600D solution-dyed polyester with a PU coating, an elastic hem cord, built-in buckles and straps, air vents to aid trailering, a mesh storage bag and an extra strap set. Covers are sized by overall length, and the size guide matches yours to a size. The cover carries a Lifetime warranty. For a craft kept in a garage, the Satin Shield is our indoor cover (Satin storage bag included). See all our jet ski covers.

A jet ski under a blue and black Weatherproof Shield cover on its trailer in a driveway at dusk, seen from the front three-quarter angle

Trailerable Cover

AllGuard Weatherproof Shield Jet Ski Cover (Trailerable)

For after the flush, once the craft is dry: a water-resistant, trailerable cover with an elastic hem cord, built-in buckles and straps and air vents to aid trailering. Sized by length.

4 colors: Blue / Black, Gray / Black, Red / Black, Yellow / Black

  • Under 90 inP0
  • Under 102 inP1
  • Under 115 inP2
  • Under 125 inP3
  • Under 135 inP4
  • Under 145 inP5
  • Up to 160 inP6

Lifetime Warranty

Jet ski flushing FAQ

All three makers give a flush procedure in their 2026 manuals. Sea-Doo's 2026 operator's guides flush the exhaust system and warn that failure to flush it when necessary will severely damage it. Yamaha's 2026 owner's manuals flush the cooling water passages to prevent them from clogging with salt, sand or dirt. Kawasaki's 2026 STX 160 owner's manual says flushing helps prevent salt or other mineral deposits that can lead to cooling system blockage and overheating.

Covering the craft once it's dry?

Covers go by your jet ski's overall length. Match yours in the size guide.

Open the size guide

Sources

  1. 2026 GTI, GTR and WAKE Series Operator's Guide (219002462): Exhaust System Flushing label, supercharged engines (p. 66); Clean, Drain and Dry (p. 44); Flushing the Exhaust System (pp. 161-163); Post-Operation Care (p. 168); Draining the Exhaust System (pp. 171-172); Troubleshooting, Engine Overheats (p. 234) (opens in a new tab)BRP (Sea-Doo) · 2026-10-31
  2. 2026 GTX Series Operator's Guide (219002465): Flushing the Exhaust System (pp. 145-147) (opens in a new tab)BRP (Sea-Doo) · 2026-10-27
  3. 2026 Spark Series Operator's Guide (219002469): Flushing the Exhaust System (pp. 128-129) (opens in a new tab)BRP (Sea-Doo) · 2026-10-31
  4. 2026 RXT-X 325 Operator's Guide: Flushing the Exhaust System (run time) (opens in a new tab)BRP (Sea-Doo) · 2026-10-27
  5. 2026 Wake Pro Operator's Guide: Flushing the Exhaust System (run time) (opens in a new tab)BRP (Sea-Doo) · 2026-10-27
  6. 2026 FishPro Scout Operator's Guide: Flushing the Exhaust System (run time) (opens in a new tab)BRP (Sea-Doo) · 2026-10-27
  7. 2026 FishPro Sport Operator's Guide: Flushing the Exhaust System (run time) (opens in a new tab)BRP (Sea-Doo) · 2026-10-27
  8. 2026 FishPro Trophy Operator's Guide: Flushing the Exhaust System (run time) (opens in a new tab)BRP (Sea-Doo) · 2026-10-27
  9. How to Winterize Your PWC (Personal Watercraft) (dated 6/9/26) (opens in a new tab)BRP (Sea-Doo) · 2026-10-27
  10. Can you run the motor of your Sea-Doo out of the water? (undated FAQ) (opens in a new tab)BRP (Sea-Doo) · 2026-10-27
  11. 2026 WaveRunner VX-C/VX/VX DELUXE/VX CRUISER/VX LIMITED Owner's/Operator's Manual, U.S.A. Edition, LIT-18626-15-77: Flushing the cooling water passages (pp. 100-101) (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2026-10-30
  12. 2026 WaveRunner FX HO/FX CRUISER HO Owner's/Operator's Manual, U.S.A. Edition, LIT-18626-15-73: Flushing the cooling water passages (p. 114) (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2026-10-31
  13. 2026 WaveRunner SUPERJET Owner's/Operator's Manual, U.S.A. Edition, LIT-18626-15-71: Flushing the cooling water passages (pp. 63-64) (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2026-10-30
  14. Maintenance Matters: A Simple Guide for the Longevity of Your WaveRunner (2021): Corrosion; Post-Operation Checks and Maintenance (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2026-10-27
  15. JET SKI STX 160LX / STX 160X Owner's Manual, JN1500F/H (2026): End of the Day Checklist (p. 142); Cooling System Flushing (pp. 187-189) (opens in a new tab)Kawasaki Motors Corp., U.S.A. · 2026-10-30
  16. JET SKI Ultra 310LX / 310LX-S Owner's Manual, JV1500A/B (2026): Supercharger Lubrication (p. 28); stern figure (p. 32); End of the Day Checklist (p. 149); Cooling System Flushing (pp. 194-195) (opens in a new tab)Kawasaki Motors Corp., U.S.A. · 2026-10-30
  17. How to Flush a Jet Ski, WaveRunner or Personal Watercraft (PWC) (opens in a new tab)Discover Boating (NMMA) · 2026-10-27

Find Your Size

Measure your jet ski bow to stern in a straight line, then enter the length in inches.

  1. Under 90 inP0
  2. Under 102 inP1
  3. Under 115 inP2
  4. Under 125 inP3
  5. Under 135 inP4
  6. Under 145 inP5
  7. Up to 160 inP6
Full Size Guide

In inches. Decimals are fine.

Covers for Your Jet Ski

All Covers