Fitting

How to Put On a Jet Ski Cover

Start with a clean, dry jet ski and a cooled exhaust, and fasten the Weatherproof Shield with its own straps. Here's what's on our covers, what the makers' manuals say, and where we don't have guidance yet.

By Alex Quinn 6 min read

A red-and-black two-tone cover draped loosely over a jet ski on its trailer in a tidy home garage, the garage door open to daylight

To put on a jet ski cover, start with a clean, dry jet ski whose exhaust has cooled, fit the cover without over-stretching it, and fasten it with the cover's own straps if it has them. That's as far as our verified guidance goes. We don't yet publish a step-by-step fitting sequence for our covers, and none of the 2026 Sea-Doo, Kawasaki and Yamaha owner's manuals checked for this page explains how to put a cover on a personal watercraft.

Below: what to do before you cover, what's on each of our covers, how to fasten the Weatherproof Shield, and what Kawasaki and Yamaha say to watch for once the cover is on. If your question isn't answered here, contact us.

Before you cover your jet ski

Put the cover on a clean, dry jet ski once the exhaust has cooled. That's our guidance for both the Weatherproof Shield and the Satin Shield. The cool-exhaust rule is ours. The makers' 2026 manuals checked for this page don't mention cooling before covering, and we don't give a wait time or a temperature.

Kawasaki's 2026 STX 160LX/160X owner's manual covers the craft side in its storage preparation. It says to "Wash the exterior and dry it thoroughly." The same storage list, also found in Kawasaki's 2026 Ultra 310LX/310LX-S manual, says to "Remove the seats and open the inspection vent hatch to insure adequate ventilation and prevent condensation from forming," and to "Cover the watercraft and store it in a clean, dry place." Kawasaki doesn't say how to put the cover on.

Sea-Doo's 2026 GTI, GTR and Wake operator's guide (the Spark, GTX, RXT-X 325, Wake Pro and FishPro guides carry the same line) says that if the watercraft is to be stored outside, "cover it with an opaque tarpaulin to prevent sun rays and grime from affecting the plastic components, watercraft finish, as well as preventing dust accumulation." A notice on the same page of the GTI, GTR and Wake guide adds: "Never leave the watercraft stored in direct sunlight. Never store watercraft in a plastic bag." In this storage line, Sea-Doo names a tarpaulin, not a fitted cover, and gives no method for putting it on.

What's on your cover

Before you fit it, it helps to know what your cover has. Here is what the supplier's product sheet lists for each of our jet ski covers.

From the supplier's product sheet dated 2026-09-15; the Satin Shield's storage bag is confirmed by our operations team. The sheet doesn't say where the straps attach or what the grommets are for.
CoverHemFasteningOther details
Weatherproof Shield (trailerable)An elastic hem cordBuilt-in buckles and straps, plus an extra strap setAir vents to aid trailering; mesh storage bag; 600D solution-dyed polyester with a PU coating
Satin Shield (indoor)Elastic front and rear hemsNo straps or buckles listedReinforced grommets on both sides; sheared fleece interior; no mirror pockets; satin storage bag included

The Weatherproof Shield is our water-resistant, trailerable cover. For it, the supplier sheet says only "Elastic Hem cord" and doesn't say where the cord runs or where the straps attach. The Satin Shield is our indoor cover, and its supplier spec lists no straps or buckles. Neither cover's spec lists a front or rear label. Both are on the jet ski covers page, and our covers carry a Lifetime warranty.

Putting the cover on

We don't yet publish a step-by-step fitting sequence for our covers, and the supplier hasn't given us one. We can't yet tell you which end goes on first, where the buckles and straps go, or how tight to make them. If you'd like help fitting yours, contact us.

For reference only, Kawasaki's undated instruction sheet for its own Vacu-Hold accessory cover, not for ours, has the owner fit that cover "over handlebars and mirrors," then pull it "over front of machine, down under bow hull," then "over back, one side at a time."

If the cover looks too small or too large, check the size guide, which matches covers to a jet ski's overall length, and our guide to how to measure a jet ski for a cover. Mirrors, towers and other add-ons have their own page: will the cover fit with accessories. For taking the cover off and putting it away, see how to fold and store your cover.

Note

What we don't cover here yet

We don't yet publish a step-by-step fitting sequence for our covers, which end goes on first, where the straps go or how tight to make them, or how long to let the exhaust cool before covering. This page also doesn't cover fitting a jet ski on a lift, at a dock or around accessories. For help with any of these, contact us through our contact page.

Fastening the cover

On the Weatherproof Shield, fasten the built-in buckles and straps; the supplier also includes an extra strap set. Three care points while you fit it:

  • Don't over-stretch the cover as you fit it.
  • Don't drag it over rough or damaging surfaces.
  • Attach it only with its own straps, not added straps, bungee cords or any other securing method.

For more on wind and the road, see how to keep your cover from blowing off and can you trailer a jet ski with the cover on. The Satin Shield is an indoor cover, and its spec lists no straps.

Trailerable Cover

AllGuard Weatherproof Shield Jet Ski Cover (Trailerable)

Water-resistant and trailerable: an elastic hem cord, built-in buckles and straps, an extra strap set and air vents to aid trailering.

4 colors: Blue / Black, Gray / Black, Red / Black, Yellow / Black

  • Under 90 inP0
  • Under 102 inP1
  • Under 115 inP2
  • Under 125 inP3
  • Under 135 inP4
  • Under 145 inP5
  • Up to 160 inP6

Lifetime Warranty

After the cover is on

Kawasaki and Yamaha both warn that water can collect in the footwells of a jet ski left outside, even under a cover. Kawasaki's 2026 STX 160LX/160X owner's manual says, "If the watercraft is left outside, even covered, water can collect in the footwells on either side of the seat," and that water left there "can cause the paint to bubble and peel, and the mat to peel off the deck." Kawasaki's remedy for a craft left on a trailer is to "raise the trailer tongue so that water cannot accumulate in the footwells." Yamaha's 2021 Maintenance Matters guide says that, stored outdoors, "even units with factory covers installed can accumulate water in the footwells," and to "check and drain the footwells at least twice a month."

Each remedy is that maker's own, and your owner's manual has the final say on how to store your model. For more, see water pooling and moisture under your cover, using your cover in rain and snow and storing a jet ski outside.

Jet ski cover fitting FAQ

More answers are in our help center.

Common Questions

No. Our guidance is to put the cover on a clean, dry jet ski once the exhaust has cooled. We don't give a wait time or a temperature, and the makers' 2026 manuals checked for this page don't mention cooling before covering.

Find Your Size

Measure your jet ski bow to stern in a straight line, then enter the length in inches.

  1. Under 90 inP0
  2. Under 102 inP1
  3. Under 115 inP2
  4. Under 125 inP3
  5. Under 135 inP4
  6. Under 145 inP5
  7. Up to 160 inP6
Full Size Guide

In inches. Decimals are fine.

Covers for Your Jet Ski

All Covers