Care

Water Pooling and Moisture Under Your Cover

The Weatherproof Shield is water-resistant, and Kawasaki and Yamaha say water can still collect in the footwells of a covered craft kept outside. Here's what Kawasaki, Sea-Doo and Yamaha say about drying and ventilating the craft, and what we can tell you about our cover's vents.

By Alex Quinn 8 min read

The Weatherproof Shield is water-resistant. Put it on only when the jet ski is clean and dry and the exhaust has cooled. Even then, a cover doesn't keep the footwells dry: Kawasaki's 2026 STX 160 owner's manual says a craft left outside, even covered, can collect water in the footwells on either side of the seat, and Yamaha's 2021 Maintenance Matters guide says the same of WaveRunners stored outdoors with factory covers.

Below: what the 2026 manuals say about drying the craft before you cover it and ventilating it for storage, what the makers say about water that collects anyway, what we can and can't tell you about the vents on our cover, and where we don't have guidance yet. For rain and snow in general, see using your cover in rain and snow, and for fitting the cover, how to put on a jet ski cover.

Note

Your owner's manual has the final say

The manuals quoted here are Kawasaki's 2026 STX 160LX/STX 160X owner's manual, Sea-Doo's 2026 GTX operator's guide (its storage chapter matches the 2026 GTI, GTR and Wake guide) and Yamaha's 2026 VX-family owner's manual. The other maker sources are web pages and Yamaha's 2021 Maintenance Matters guide. Steps differ by make and model; where this page and your manual differ, follow your manual.

Before you cover: dry the craft

Our own guidance is short: cover the jet ski only once it is clean and dry and the exhaust has cooled. The 2026 manuals add steps for drying the craft itself. These are about the jet ski, not the cover.

  • Kawasaki (2026 STX 160): wash the exterior and dry it thoroughly. Wash the engine compartment with fresh water, remove the drain screws in the stern to let the water out, and wipe up any water left in the compartment.
  • Sea-Doo (2026 GTX): lift the front end of the craft to drain the bilge completely through the bilge drain plugs, then wipe off any residual water in the engine compartment.
  • Yamaha (2026 VX): once the bilge water has drained from the stern drain plug holes, wipe up any remaining moisture in the engine compartment with a dry cloth. When cleaning, wipe the engine and engine compartment, and the hull, deck and jet pump, with a dry cloth, and let the engine compartment air dry completely before the seats go back on.

None of the 2026 manual passages cited here gives a drying time. Sea-Doo's owner web page on water in the engine suggests, if possible, leaving the seat off or the access panels removed for several hours after a ride so remaining water can evaporate before you cover the craft. It gives no exact number of hours, and we don't publish one either. Yamaha's 2021 Maintenance Matters guide puts it broadly: make sure any item or area of the boat is bone-dry before closing it up.

Before the cover goes on

Ventilating the craft for storage

The makers' condensation steps below are about the craft's engine compartment and bilge, not about any cover.

  • Kawasaki (2026 STX 160): remove the seats and open the inspection vent hatch, which Kawasaki says ensures adequate ventilation and prevents condensation from forming; then cover the watercraft and store it in a clean, dry place. The vent hatch is on the craft.
  • Sea-Doo (2026 GTX): the seat should be removed during storage, which Sea-Doo says will prevent engine-compartment condensation and possible corrosion. The guide also says to unscrew the drain plugs whenever the craft is on the trailer, so water in the bilge can drain out, which it says helps reduce condensation. Sea-Doo's 2026 GTI, GTR and Wake guide warns to make sure the bilge drain plugs are secured before launching.
  • Yamaha (2026 VX): its care and storage chapter gives the drying steps above but no condensation, ventilation or cover step.

Neither Sea-Doo nor Kawasaki says how to keep the seats off on a craft stored outside, so if yours lives outdoors, ask your dealer. For where each maker says to store the craft, see is it okay to store a jet ski outside; for full storage prep, see how to winterize a jet ski and jet ski winter storage.

A jet ski in a garage with its seat removed and the engine compartment open

Water that collects in the footwells

Kawasaki's 2026 STX 160 manual says not to let water collect in the footwells during storage, and that water left there can cause the paint to bubble and peel and the mat to peel off the deck. Yamaha's 2021 Maintenance Matters guide says pooled water in a WaveRunner's footwells should be removed as soon as possible to prevent damage to paint (such as osmotic blistering), graphics and traction mats. For craft stored outdoors, even under factory covers, it says to check and drain the footwells at least twice a month.

We don't recommend a storage position. For what each maker says, see storing a jet ski outside, and follow your owner's manual. For water inside the hull, see water in a jet ski hull.

The vents on the Weatherproof Shield

The Weatherproof Shield is two-tone 600D solution-dyed polyester with a polyurethane-coated back. It's water-resistant, with an elastic hem cord, built-in buckles and straps, and air vents to aid trailering. Aiding trailering is the only purpose the supplier gives for the vents.

We don't publish how many vents there are or where they sit, whether air or moisture passes through the fabric, or how the cover behaves with condensation underneath. We make no claim that the vents dry the craft or reduce condensation, so follow the makers' drying and storage steps above.

The cover carries a Lifetime warranty. The Satin Shield is our indoor stretch cover. See all our jet ski covers.

Trailerable Cover

AllGuard Weatherproof Shield Jet Ski Cover (Trailerable)

Water-resistant 600D solution-dyed polyester with a PU-coated back, an elastic hem cord, built-in buckles and straps, and air vents to aid trailering. Sized by overall length.

4 colors: Blue / Black, Gray / Black, Red / Black, Yellow / Black

  • Under 90 inP0
  • Under 102 inP1
  • Under 115 inP2
  • Under 125 inP3
  • Under 135 inP4
  • Under 145 inP5
  • Up to 160 inP6

Lifetime Warranty

Water pooling on top of the cover

Yamaha's 2023 web article on choosing a PWC cover says to avoid excess fabric that will pucker or create a pocket that holds rainwater. The BoatUS Foundation, writing about boat covers in its Findings #60 (Sept 2022), says to check a covered boat at least once a month, and after snow or heavy rain, through the off season, and to get rid of any pooling water; it says the extra weight can damage the boat, trailer or lift, or make the cover rip.

We don't publish support-pole or other pooling-prevention guidance for our cover yet. If water keeps pooling on yours, contact us.

Where we don't have guidance yet

We don't publish guidance on these yet:

  • Whether air or moisture passes through the fabric of our covers
  • How many vents the Weatherproof Shield has, and where they sit
  • How condensation behaves under a cover. The makers' condensation steps quoted above are about the craft, not the cover.
  • How long to wait before covering a wet craft, beyond clean, dry and a cooled exhaust
  • Support poles or other ways to stop water pooling on the cover

For any of these, contact us. For cleaning and caring for the cover itself, see how to wash and care for your jet ski cover. More answers are in the help center.

Plastic wraps and mold: what Sea-Doo says

BRP's Sea-Doo page on winterizing a personal watercraft says to dry the craft thoroughly, cover it with a breathable, fitted cover and store it in a dry, ventilated place. It says to avoid wrapping a PWC in plastic or non-breathable materials, which it says can cause mold.

Sea-Doo's 2026 GTX guide says never to store a watercraft in a plastic bag. For a craft stored outside, it says to cover it with an opaque tarpaulin, giving sun rays, grime and dust as the reasons.

Jet ski cover vents and moisture FAQ

They're air vents to aid trailering, and that's the only purpose the supplier gives. We don't publish how many vents there are, where they sit, or how the cover behaves with condensation underneath, and we make no claim that the vents dry the craft.

Find Your Size

Measure your jet ski bow to stern in a straight line, then enter the length in inches.

  1. Under 90 inP0
  2. Under 102 inP1
  3. Under 115 inP2
  4. Under 125 inP3
  5. Under 135 inP4
  6. Under 145 inP5
  7. Up to 160 inP6
Full Size Guide

In inches. Decimals are fine.

Covers for Your Jet Ski

All Covers