Maintenance

Water in Your Jet Ski Hull: How Much Is Normal?

A little water in the hull is expected; a lot of it, or water in the engine, is another matter. What Sea-Doo, Yamaha and Kawasaki say about where it comes from, how to drain it and when to call a dealer.

By Alex Quinn 20 min read

Jet ski on its trailer under a red and black AllGuard Weatherproof Shield cover on a wet driveway after rain

Some water in a jet ski's hull is expected. Sea-Doo says water may occasionally get inside the engine compartment, and it calls small amounts minimal, nuisance water that its onboard bailer system pulls out as you ride. Yamaha's 2026 owner's manuals say a small quantity of bilge water will remain in the engine compartment even after it's drained on the water. None of the sources behind this guide gives a normal amount, in inches or gallons, for a craft sitting on its trailer.

What the makers do give is the line between nuisance water and a problem: a significant amount you can't explain, or water that may have reached the engine. Here is what each one says.

The short answer

  • A little is normal. Yamaha says a small quantity of bilge water remains even after draining on the water, and Sea-Doo calls small amounts nuisance water.
  • No source here gives a normal amount for a craft at rest. Kawasaki's one figure for water in the hull, 51 mm (2 in.), is for a craft that has capsized.
  • A significant amount with no rain and no riding to explain it is a reason to see a dealer, Sea-Doo says.
  • Drain it out of the water: remove the stern drain plugs, let the bilge run out, then clean and refit the plugs before launching.
  • Water in the engine is a dealer job in all three makers' manuals.

How much water in the hull is normal?

Start by telling two places apart. The footwells are on the deck, on either side of the seat, in the words of Kawasaki's 2026 STX 160 manual. The bilge is inside the hull: Yamaha's 2026 VX manual defines bilge water as water that has collected in the engine compartment. This section is about the bilge; rain in the footwells comes further down.

Here is what the sources say about the amount:

  • Sea-Doo: its owner page on water in the hull says water may occasionally get inside the engine compartment. It calls small amounts minimal, nuisance water, and says one of the easiest ways to get rid of it is simply to ride: the onboard bailer system uses the natural suction of the jet pump to pull water out of the hull. It may also be possible to bail or sponge the water out before you launch.
  • Yamaha: the 2026 manuals say a small quantity of bilge water will remain in the engine compartment even after the bilge is drained on the water. To drain it completely, Yamaha says to take the craft out of the water and drain it on land.
  • Discover Boating: its PWC maintenance guide says to check for water in the bilge before heading out, and that a lot of water below the engine could mean a leak in a cooling hose or a fitting in the hull.
Hand pressing a yellow sponge into a shallow puddle at the bottom of an open engine compartment, seat removed

Kawasaki's 2-inch figure is for a capsize

The only measurement of water in the hull in the three makers' manuals cited here comes from Kawasaki, and it applies to a craft that has capsized, not one that sat in the rain. Kawasaki's 2026 STX 160 owner's manual says that after a capsize, if more than 51 mm (2 in.) of water is present, measured from the bottom of the engine compartment, it may have entered the intake tract and will cause severe engine damage: don't attempt to start the engine; tow the craft slowly to shore and drain it. If the watercraft was "correctly righted to its starboard side," in the manual's words on that page, and there is less than 51 mm (2 in.) of water in the hull, it says to start the engine so the bilge pump can help remove water from the engine compartment. That threshold is Kawasaki's, for that situation. It isn't a general normal level.

When it's more than nuisance water

Sea-Doo draws the line by cause. If you find a significant amount of water in the engine compartment and it hasn't rained and you haven't been riding, its owner page says to take the craft to the dealer for inspection, to make sure there are no leaking cooling lines, loose hose clamp fittings or unforeseen damage. Before you decide, check whether something on this list explains it:

Is the water explained?

Where the water comes from

The makers name the ways water gets in. Each one below is credited to the document that says it.

Rain while it's stored

Sea-Doo's owner page lists rainwater that seeps in through a seat left ajar during storage, and a seat that wasn't properly latched and sealed after it was removed. Yamaha's 2021 Maintenance Matters guide says worn seat and hatch seals will allow water entry, and puts a seal inspection in its pre-operation checks. Rain also lands on top of the deck: Kawasaki's 2026 STX 160 manual and Yamaha's 2021 guide both say water can collect in the footwells of a craft left outside, even under a cover.

Riding

Sea-Doo's 2026 operator's guide for the GTI, GTR and Wake series says the craft cannot be totally watertight, because combustion engines need air to operate. It says tight turns or other maneuvers that keep the air inlet openings under water for a prolonged time will let water seep into the bilge, and warns that turning constantly in tight circles, plunging the bow through waves or capsizing may let water seep in and cause severe damage to internal engine parts. Sea-Doo's owner page adds aggressive riding where the bow is frequently buried below the waves.

Drain plugs

Yamaha's 2026 VX manual warns that if the stern drain plugs aren't tightened securely before launching, water may flood the engine compartment and cause the craft to submerge, and that dirt or sand on the threads or O-rings could damage the plugs, allowing water into the engine compartment. Kawasaki's 2026 STX 160 manual says that if its two stern drain screws come loose, the craft may flood or become swamped, with the possibility of sinking or severe engine damage.

Leaks and damage

Sea-Doo's 2026 guide has a troubleshooting entry for water found in the bilge. It lists four possible causes, and sends every one to an authorized dealer: a bilge pump system malfunction, an exhaust system leak, a worn carbon ring at the drive shaft, and a hull or deck seal that's displaced or has loose fasteners. Kawasaki's 2026 manual names two more:

  • Hull damage. Kawasaki says damage to the hull may cause a leak that the bilge pumping system is not designed to drain, so return to shore immediately if the hull is damaged in any way.
  • A clogged breather hole. In the bilge-flushing section, Kawasaki says that if the small breather hole in the bilge-hose fittings is clogged, the engine compartment will fill with water when the engine stops or idles.

A craft left floating at a dock has risks of its own; see can you leave a jet ski in the water?

How to drain the bilge and footwells

The three makers drain the bilge the same basic way: out of the water, through drain plugs in the stern (Kawasaki calls them drain screws). The steps below put the manuals' instructions in order. Your own owner's manual comes first.

Drain the bilge on land

  1. Step 1: Get the craft out of the water

    Kawasaki's 2026 STX 160 manual says to open its drain screws only when the craft is out of the water, and Yamaha's 2026 manuals do the full drain on land. Sea-Doo's owner page suggests loosening the drain plug after you pull out at the ramp, so water drains as you drive home.

  2. Step 2: Remove the stern drain plugs

    Yamaha's 2026 VX manual says to loosen the stern drain plugs and remove them. Kawasaki's pre-ride check drains any water out of the engine compartment by removing the drain screws.

    Two hands unscrewing a black drain plug from the transom beside the jet nozzle as a thin stream of water runs out
  3. Step 3: Let the bilge run out

    Yamaha raises the bow, for example by placing the craft on a slope, to drain the bilge water from the engine compartment. Sea-Doo's 2026 guide lifts the front end to drain the bilge completely through the bilge drain plugs. These are draining steps, not positions for storing the craft.

    Two thin streams of water running from open drain holes at the stern of a white jet ski onto gravel
  4. Step 4: Mop up what's left

    Yamaha says to wipe up remaining moisture in the engine compartment with a dry cloth, and its 2021 guide says to mop up excess water in the bilge and let it dry completely before refitting the seat. Sea-Doo suggests leaving the seat off or the access panels removed for several hours after a ride so the remaining water can evaporate before you cover the craft.

  5. Step 5: On a Kawasaki, check the air box drain

    Kawasaki's 2026 pre-ride check has you check the air box drain cap for water and discharge any you find.

  6. Step 6: Clean and refit the plugs

    Yamaha says to check the plugs and their O-rings for damage, clean any dirt or sand off the threads and O-rings, and tighten the plugs until they stop. Kawasaki says to install the drain screws securely once all the water has drained, and Sea-Doo to make sure the plugs are secured before launching. Discover Boating suggests a reminder, like a note on the handlebar, so you don't forget to put them back.

Sea-Doo's 2026 guides add a rule for the trailer: unscrew the drain plugs whenever the craft is on the trailer, which lets water that collects in the bilge drain out and helps reduce condensation, and make sure they're secured before launching. Yamaha's 2026 VX manual puts a bilge check in its pre-operation checks: make sure no bilge water has collected in the engine compartment, and drain it if it has. Draining the bilge is also part of storage prep; the full routine is in how to winterize a jet ski, and the plugs are on the pre-season list in getting your jet ski ready for summer.

From each maker's 2026 documents; see the sources below. The owner's manual for your model and year decides.
Maker and documentWhile ridingOut of the waterBefore launching
Sea-Doo (2026 operator's guides; owner page)The onboard bailer system uses jet pump suction to pull water out as you rideLift the front end to drain through the bilge drain plugs; unscrew the plugs whenever it's on the trailerBilge drain plugs properly secured
Yamaha (2026 VX owner's manual)Jet vacuum bilge draining system; run as straight as possible above planing speed for at least 2 minutes; a small quantity remainsRemove the stern drain plugs and raise the bow, on a slope for example; wipe the compartment dryPlugs and O-rings clean and undamaged, tightened until they stop
Kawasaki (2026 STX 160 owner's manual)Jet vacuum drainage system; works only with the engine running on waterRemove the two stern drain screws, only with the craft out of the waterDrain screws securely tightened

The footwells

Footwell water sits on the deck, not in the bilge, and Kawasaki and Yamaha deal with it in their storage advice. The documents disagree on how the craft should sit while stored:

  • Kawasaki's 2026 STX 160 manual says not to let water collect in the footwells during storage, and for a craft left on a trailer, to raise the trailer tongue so water cannot accumulate in them.
  • Yamaha's 2021 Maintenance Matters guide says raising the bow of a trailered unit without footwell drains can help water drain from the footwells, and that a unit with footwell drains should be horizontal with the drain insert holes clear.
  • Sea-Doo's owner page suggests storing the craft on its trailer with the drain plugs loose and the bow slightly elevated, to keep rainwater from collecting.
  • Yamaha's 2026 owner's manuals warn to store the craft upright in a horizontal position, because otherwise fuel could leak into the engine or engine compartment and create a fire hazard.

So this guide doesn't choose a position: follow the storage section of the owner's manual for your model and year. Whatever it says, keep checking the footwells. Yamaha's 2021 guide says to check and drain them at least twice a month when the craft is stored outdoors. More on keeping a craft outdoors is in storing a jet ski outside.

Important

Check the storage warning in your manual

Yamaha's 2026 manuals print this as a WARNING: "Always place the watercraft upright in a horizontal position when storing it, otherwise fuel could leak out into the engine or engine compartment, which could create a fire hazard." If your manual gives a different position, follow your manual.

Are Yamaha WaveRunners self-draining?

Partly, going by Yamaha's own documents, which don't use the term self-draining. All nine of Yamaha's 2026 U.S. owner's manuals describe a jet vacuum bilge draining system: while the craft is operating, bilge water in the engine compartment is drawn in by the vacuum generated in the jet pump and discharged through the jet thrust nozzle. To drain the bilge this way, the 2026 VX manual says to run the craft as straight as possible and above planing speed for at least 2 minutes. It also warns not to run at full throttle while bilge water remains, or for at least 1 minute after a restart, because the bilge water can splash into the engine and cause severe damage.

The system doesn't empty the bilge. The same manuals say a small quantity of bilge water will remain even after draining on the water, and that to drain it completely you take the craft out of the water and drain it on land, through the stern drain plugs. Yamaha describes the system as working while the craft is operating, so on the trailer the drain plugs are the way out.

The footwells are a separate question. Yamaha's 2021 Maintenance Matters guide treats units equipped with footwell drains differently from units without them. It doesn't list which models have footwell drains, so check your manual or ask your Yamaha dealer.

Water in the engine after a flip or swamping

Water in the engine is not bilge water, and all three makers' manuals send a craft with water in the engine to a dealer. The warnings are blunt. Kawasaki's 2026 STX 160 manual says that if water enters the engine it will cause severe damage, not to operate the craft or try to start the engine until it is completely empty of water, and that water left in the engine more than a few hours will destroy the crankshaft bearings and damage other internal engine parts. If the craft is swamped, it says, water may enter the engine through the throttle body, and water may also enter the fuel tank. Sea-Doo's 2026 guide says never to try to crank or start a submerged or water-flooded engine, because water trapped in the intake manifold would flow toward the engine and possibly cause severe engine damage.

Which way you roll a capsized craft matters too. Sea-Doo's owner page says to check the warning label at the stern, which shows the direction to right the craft to prevent water entering the engine. Kawasaki's manual says rolling the capsized craft counterclockwise (to its starboard side) can cause water in the exhaust system to run into the engine, and to always turn it clockwise so that the port side always faces downward. Its 2-inch rule on the next page speaks of a craft "correctly righted to its starboard side"; the manual doesn't reconcile the two wordings, so follow the capsize procedure in your own manual, or ask your dealer. Here is what each manual says to do:

Summarized from each manual's capsize and submerged-watercraft sections. Read the full procedure in your own manual.
Maker and documentRighting itRestartingSubmerged or flooded
Sea-Doo 2026 GTI, GTR and Wake guideEngine off and the D.E.S.S. key off its post; a label on the stern shows how to turn it uprightIf it has been upside down for 5 minutes, don't crank the engine; see a dealer as soon as possibleDrain the bilge, rinse it with fresh water after salt water, never crank or start it; dealer as soon as possible
Yamaha 2026 VX manualClip off the engine shut-off switch; turn it over immediately from the rearRun at planing speed to drain the bilge; no full throttle for at least 1 minuteDrain the storage compartments and the bilge; dealer service as soon as possible
Kawasaki 2026 STX 160 manualEngine stopped; always turn it clockwise so the port side faces downMore than 51 mm (2 in.) of water in the engine compartment: don't start it; tow it to shoreDrain the engine compartment and check the air box drain cap; water there means the dealer

If the craft has been swamped or submerged, all three manuals have you drain the bilge. Sea-Doo and Yamaha then say to have a dealer service it as soon as possible. Sea-Doo and Kawasaki add: don't try to start it (Kawasaki: not until the engine is completely empty of water). Kawasaki's After Submerging procedure starts by removing the stern drain screws and checking the drain cap at the bottom of the air box; if there's water there, it says to take the craft to the dealer immediately, because there is a strong possibility water has entered the engine. The procedure continues with further checks of its own. Follow it exactly as your manual prints it, or let the dealer do it.

Important

Water in the engine: see a dealer

Kawasaki says water left in the engine more than a few hours will destroy the crankshaft bearings. Sea-Doo and Yamaha say to have a submerged craft serviced by a dealer as soon as possible. Don't run it with water in the engine.

Bilge pumps: what the makers say

All three makers describe bilge systems driven by the jet pump while the engine runs: Sea-Doo's onboard bailer, Yamaha's jet vacuum bilge draining system and Kawasaki's jet vacuum drainage system (see the table above). Beyond that:

  • Sea-Doo's 2026 GTI, GTR and Wake guide lists a fuse for a bilge pump, if equipped, and its troubleshooting table sends a bilge pump system malfunction to a dealer.
  • Kawasaki's 2026 STX 160 manual says to check that the system is working at the intervals in its maintenance chart, clear debris from the pump intakes, and flush the bilge system on that schedule or whenever you suspect it's blocked.

How many GPH? None of the three makers' 2026 manuals cited here gives a flow rating for its bilge system, in gallons or liters per hour, and none of the other sources behind this guide gives one for a personal watercraft. So this guide doesn't give a number. If you're thinking of adding a pump, ask your dealer what suits your model.

Rain while it's covered

A cover helps, and it doesn't make the craft watertight. Sea-Doo's owner page says that taking care of the craft in storage, covering it to ward off rainwater and avoiding extreme riding will go a long way toward eliminating water intrusion. But Kawasaki's 2026 STX 160 manual says that if the watercraft is left outside, even covered, water can collect in the footwells on either side of the seat, and that water left in the footwells can cause the paint to bubble and peel and the mat to peel off the deck. Yamaha's 2021 Maintenance Matters guide says even units with factory covers can collect footwell water when stored outdoors, and to check and drain the footwells at least twice a month.

Three habits come from the same sources:

  • Close it up properly. Sea-Doo names a seat left ajar during storage, and a seat that wasn't latched and sealed, as ways rain gets in; Yamaha says worn seat and hatch seals allow water entry.
  • Let it dry before you cover it. Sea-Doo suggests leaving the seat off or the access panels removed for several hours after a ride, so the remaining water can evaporate before you cover the craft.
  • Keep checking under the cover. Yamaha's twice-a-month footwell check applies to a covered craft too, and its pre-operation check covers bilge water.

Fit matters as well. Yamaha's guide to choosing a cover says to avoid excess fabric that will pucker or create a pocket that holds rainwater.

Our outdoor cover is the Weatherproof Shield: water-resistant 600D solution-dyed polyester with a PU coating, an elastic hem cord, built-in buckles and straps, and air vents to aid trailering. It comes in seven sizes, P0 to P6, by overall length, so measure the craft and match the length in the size guide. It has a Lifetime warranty; the terms are on our warranty page. It doesn't replace the checks above: Yamaha and Kawasaki both say a covered craft kept outside can still collect water in its footwells. Our Satin Shield is for indoor use only, so it isn't the cover for a craft kept outside. Both are in the jet ski covers collection. For wet weather, see using your cover in rain and snow, and for the rest of the routine, our jet ski maintenance tips.

Trailerable Cover

AllGuard Weatherproof Shield Jet Ski Cover (Trailerable)

For a jet ski kept outside on its trailer: water-resistant 600D PU-coated polyester, an elastic hem cord, built-in buckles and straps, and air vents to aid trailering.

4 colors: Blue / Black, Gray / Black, Red / Black, Yellow / Black

  • Under 90 inP0
  • Under 102 inP1
  • Under 115 inP2
  • Under 125 inP3
  • Under 135 inP4
  • Under 145 inP5
  • Up to 160 inP6

Lifetime Warranty

Water in a jet ski hull: FAQ

A little. Yamaha's 2026 manuals say a small quantity of bilge water remains even after draining on the water, and Sea-Doo calls small amounts nuisance water. None of the sources behind this guide gives a normal amount for a craft at rest. Sea-Doo says a significant amount, when it hasn't rained and you haven't been riding, is a reason to see a dealer.

Size the cover to the craft

Our covers are sized by overall length. Measure bow to stern, then match the number in the size guide.

Open the size guide

Sources

  1. What do I do if water gets in the Sea-Doo? (opens in a new tab)BRP (Sea-Doo) · retrieved 2026-10-27
  2. GTI, GTR and Wake Series Operator's Guide 2026: pre-operation (p. 39), tight turns (p. 119), capsized and submerged watercraft (pp. 128-129), bilge drain plugs (p. 139), storage (p. 175), fuses (p. 227), troubleshooting (p. 237) (opens in a new tab)BRP (Sea-Doo) · 2026 guide; read 2026-10-27
  3. 2026 WaveRunner VX Owner's/Operator's Manual, U.S.A. Edition (LIT-18626-15-77): glossary (p. 26), draining the bilge water (p. 74), pre-operation bilge check (p. 80), capsized watercraft (p. 97), storage warning (p. 103), submerged watercraft (pp. 117-118) (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2026 manual; read 2026-10-27
  4. GTX Series Operator's Guide 2026: bilge drain plugs (p. 127) (opens in a new tab)BRP (Sea-Doo) · 2026 guide; read 2026-10-27
  5. Yamaha WaveRunners 2021 Maintenance Matters Guide (pre- and post-operation checks, p. 9; storage and care, pp. 20-21) (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2021
  6. Official Yamaha WaveRunners owner's manual site (the nine 2026 U.S. owner's/operator's manuals: draining the bilge water; submerged watercraft; long-term storage) (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2026 manuals; read 2026-10-27
  7. How to Choose the Right PWC Cover (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2023-10-10 (page date)
  8. JET SKI STX 160LX / STX 160X Owner's Manual, JN1500F/H (2026): bilge systems and drain screws (pp. 104-105), pre-ride check (p. 114), capsize and after submerging (pp. 134-139), end of the day (p. 142), storage (p. 152), bilge system flushing (pp. 189-191) (opens in a new tab)Kawasaki Motors Corp., U.S.A. · 2026 manual; read 2026-10-27
  9. Personal Watercraft (PWC), WaveRunner & Jet Ski Maintenance Guide (opens in a new tab)Discover Boating (NMMA) · retrieved 2026-10-27
  10. How to Flush a Jet Ski, WaveRunner or Personal Watercraft (PWC) (opens in a new tab)Discover Boating (NMMA) · retrieved 2026-10-27

Find Your Size

Measure your jet ski bow to stern in a straight line, then enter the length in inches.

  1. Under 90 inP0
  2. Under 102 inP1
  3. Under 115 inP2
  4. Under 125 inP3
  5. Under 135 inP4
  6. Under 145 inP5
  7. Up to 160 inP6
Full Size Guide

In inches. Decimals are fine.

Covers for Your Jet Ski

All Covers