Winterizing

How to De-Winterize a Jet Ski for Summer

A jet ski that sat all winter needs more than a turn of the key. Here's the spring routine from the Yamaha, Sea-Doo and Kawasaki manuals and the makers' spring articles, with each maker's limit for running the engine out of the water.

By Alex Quinn 28 min read

Jet ski on its trailer in a sunny spring driveway under a red and black AllGuard Weatherproof Shield cover

To de-winterize a jet ski, you undo last fall's storage work, then run a more thorough version of the checks you'd make before any ride. The makers file this work under different names. Sea-Doo's 2026 operator's guides call it preseason preparation. Kawasaki's 2022 and 2026 STX 160 owner's manuals have a Removal from Storage list. Yamaha's 2026 owner's manuals have no separate after-storage section; start with their pre-operation checklist, which they say to run each time the watercraft is used, together with Yamaha's 2022 article "Getting Your PWC Ready for the Season." Each step below names the document it comes from. For your own model and year, follow your owner's manual. If the ski wasn't put away properly last fall, our guide to winterizing a jet ski shows what may have been missed.

Note

Who should do the work

All three makers leave room for a dealer. BRP says it's not required, but recommended, that an authorized dealer performs a Sea-Doo's preseason preparation. Kawasaki's Removal from Storage list opens by saying to see your Kawasaki dealer for this service or do it yourself. Yamaha's 2026 manuals say to have the craft inspected by a Yamaha dealer if a problem can't be corrected with the procedures in the manual.

What each maker's spring checklist says

Here's where each maker puts the spring work, and the numbers that matter on the first start. The sections after the table take each topic in turn.

From Yamaha's 2026 U.S. owner's/operator's manuals (chart and plug details from the VX-C/VX/VX Deluxe/VX Cruiser/VX Limited manual), BRP's 2026 GTI, GTR and WAKE and Spark operator's guides, and Kawasaki's 2026 STX 160LX/STX 160X owner's manual. Your own manual has the final word.
Yamaha (2026 manuals)Sea-Doo (2026 guides)Kawasaki (2026 STX 160LX/X)
Spring sectionNone separate; use the pre-operation checklistPreseason Preparation: every task in the Every Year or 100 Hours tableRemoval from Storage
Who does itYou for pre-ride checks; the periodic chart (VX manual) goes to a Yamaha dealerA dealer, a repair shop or you; BRP recommends a dealerYour Kawasaki dealer, or you
Battery cables back onPositive (red) first, then negative (black)RED (+) first, then BLACK (-)Positive first
Engine run out of the waterNo more than 15 seconds without water; not over 4,000 r/min on land (SuperJet manual: 15 seconds)Never without water to the exhaust; never longer than 2 minutesNo more than 15 seconds at a time; never at maximum speed
Minimum depth to start60 cm (2 ft) from the bottom of the craft90 cm (3 ft) under the lowest rear of the hull, everyone aboard0.8 m (2.6 ft)
Fuel left over winterTank topped off, stabilizer addedTank filled completely, stabilizer addedTank drained; fill it in spring
Spark plugsDealer check at 10 hours, then every 100 hours or 12 months (VX manual)Replace every 2 years or 200 hoursCheck them on removal from storage

Battery preparation

Start with the battery so it's charged by the time you need the engine. Yamaha's 2026 manuals warn never to operate the watercraft if the battery doesn't have enough power to start the engine or shows any other sign of decreased power, since a loss of battery power may leave you stranded.

  1. Charge it outside the craft. BRP's 2026 Sea-Doo guides say never to charge or boost the battery while it's installed in the watercraft. BRP's 2023 article "Prepping your Sea-Doo for Summer Fun" puts it on a charger on a dry, level surface, and says it's time for a new one if it won't charge normally. Yamaha's 2026 manuals recommend having a Yamaha dealer check the voltage and charge the battery, and note that a VRLA (valve-regulated lead-acid) battery needs a special constant-voltage charger, because a conventional charger will damage it. Kawasaki's 2026 STX 160 manual's Removal from Storage list says to clean the battery terminals and charge the battery if necessary.
  2. Clean the case and terminals. Yamaha's 2022 season article uses a paste of baking soda and water on the case and terminals, and a wire brush for any corrosion left on the terminals. Sea-Doo's 2026 guides use a soft brush and a baking soda solution on the casing and posts, a firm wire brush on corroded cable ends and posts, then rinse with clear water and dry well. If your battery isn't sealed, Yamaha's article says to top up low cells with distilled water; Sea-Doo's GTI, GTR and WAKE guide describes a maintenance-free battery that needs no water added.
  3. Clear the compartment. Sea-Doo's GTI, GTR and WAKE guide says to remove any water or debris from the battery compartment before the battery goes in.
  4. Connect the positive cable first. All three makers say so. Yamaha's 2026 manuals: set the battery in place and hook the battery bands, connect the red positive (+) lead, then the black negative (-) lead, and make sure the battery is held securely; reversing the leads will damage the electrical parts. Sea-Doo's 2026 guides: the RED (+) cable first, then the BLACK (-) cable; the GTI, GTR and WAKE guide adds that reversed polarity will damage the voltage regulator. Kawasaki's 2026 STX 160LX/STX 160X manual: secure the battery with its straps, then connect the positive cable first; reversing the connections will damage the electrical system.
  5. Tighten, grease and check. Sea-Doo's GTI, GTR and WAKE guide tightens the cable screws to 4 ± 0.5 N·m (35 ± 4 lbf-in), puts dielectric grease on the posts, covers the positive post with its rubber boot and checks the cable routing. Yamaha's season article also finishes with a light coat of dielectric grease. Yamaha's pre-operation checklist then confirms that the terminals aren't damaged, the leads are connected properly and the battery is held firmly in place.
Hands cleaning a battery terminal with a small brass wire brush on a garage workbench, a tin of grease beside the battery

Fluids and fuel

With the seat off, look before you pour or start anything. Yamaha's 2022 season article says fuel and water lines should be soft and supple, and to replace any that have cracked or hardened. Kawasaki's 2026 STX 160 Removal from Storage list checks all rubber hoses, and the cooling and bilge hoses, for weathering, cracking or looseness. BoatUS's 2022 spring commissioning checklist adds the fuel tank's fill and vent hoses. Yamaha's 2026 pre-operation checklist also covers the fuel filler cap and seal, the tank, the fuel hoses and joints, and the tank breather hose. If anything is leaking fuel, Yamaha says not to start the engine, and BRP's 2026 GTI, GTR and WAKE guide says not to apply electrical power or start it, but to have it serviced.

Engine oil

Check the level before the first start. Yamaha's 2026 VX manual wants it between the minimum and maximum marks on the dipstick. Yamaha's 2021 pre-ride article notes that the method depends on the model: screw-in dipsticks are read with the engine at operating temperature and pull-out dipsticks cold, and the level should never go over the full mark. Sea-Doo's GTI, GTR and WAKE guide reads the level after a short warm-up run with the flush hose connected, between its FULL and ADD marks. Kawasaki's list says to check the level and top up with the specified oil if needed.

The makers don't agree on when to change the oil. Yamaha's season article says to change it before storage, not after; its stated reason is that contaminants from combustion and heat can turn oil acidic, and those acids can result in corrosion and etched bearings. Sea-Doo's 2026 guides change the oil and filter in their storage steps, and the Every Year or 100 Hours table that their preseason preparation points to lists an oil and filter change too. BRP's 2023 summer-prep article puts it on the spring list. Kawasaki's 2026 STX manual changes the oil as part of storage and checks the level on removal. If yours was changed at lay-up, check your manual's schedule before you change it again.

Coolant

A Sea-Doo has a closed-loop cooling system, so there's coolant to check. BRP's owner FAQ explains that the coolant is cooled as it passes through channels in the ride plate. The GTI, GTR and WAKE guide checks the level with the engine cold and the craft level, between the MIN and MAX marks on the expansion tank, and says a system that often needs coolant points to leaks or engine problems for a Sea-Doo dealer to look at. Its yearly table inspects the coolant's concentration and level, the hoses and the clamps, while replacing the coolant is a dealer job every 5 years or 300 hours. Yamaha describes its WaveRunners as raw-water cooled, and Kawasaki's Removal from Storage list checks the cooling hoses rather than a coolant level.

Fuel

What's in the tank depends on how your maker had you store the craft. Yamaha's 2026 manuals top off the tank with fresh gasoline and a stabilizer for winter, and Sea-Doo's 2026 guides fill it completely with a stabilizer added. Yamaha's season article says fuel that was conditioned properly for storage should be fine; if it wasn't, and especially if it contains ethanol, it says to empty the tank and refill with fresh fuel. Kawasaki's 2026 STX manual drains the tank for storage, so its Removal from Storage list includes filling the tank and closing the filler cap securely. The same manual warns never to fill the tank so far that fuel rises into the filler neck, since heat can make it expand and overflow through the vents in the tank cap. If you drain old gasoline, Kawasaki says never to discard it: return it to an authorized recycling center.

Two more fuel checks. Yamaha's 2026 pre-operation checklist looks for water in the water separator and has you drain it if any has collected. And Sea-Doo's 2026 guides point out that the U.S. EPA prohibits gasoline with more than 10% ethanol in these engines.

Spark plugs and electrical

No maker's schedule we read calls for new plugs every spring; each maker sets its own schedule for checking or replacing them.

  • Sea-Doo: BRP's 2023 summer-prep article starts with the plugs, saying they should be replaced every couple of seasons, and to inspect or change them as your operator's guide indicates. The 2026 GTI, GTR and WAKE and Spark guides schedule spark plug replacement every 2 years or 200 hours. Their procedure: remove the ignition coil, blow grime off the plug area with compressed air, unscrew the plug with a spark plug socket, check the gap with a wire feeler gauge and replace any plug that's out of spec. BRP warns not to adjust the gap on this type of plug, because that could weaken the electrodes and lead to severe engine damage. Anti-seize goes on the threads, and the GTI, GTR and WAKE guide torques the plug to 18 ± 2 N·m (159 ± 18 lbf-in).
  • Kawasaki: the 2026 STX manual's Removal from Storage list says to check the spark plugs. Its spark plug section says to replace a plug whose electrodes are rounded or damaged, that has built-up carbon or that is cracked; to measure the gap with a wire-type gauge; and not to adjust the gap, but to replace a plug that's out of spec. Molybdenum disulfide grease goes on the threads, and the plugs are tightened to 13 N·m (115 in·lb).
  • Yamaha: the 2026 VX manual's periodic maintenance chart checks the spark plugs at the first 10 hours and then every 100 hours or 12 months, and asks you to have a Yamaha dealer perform the checks in that chart. Its trouble-recovery table also sends a fouled or defective plug to a dealer.

Connections and controls

Yamaha's 2022 season article says to check all electrical connections, clean off any buildup or corrosion with a wire brush and baking soda paste, and finish with a light coat of dielectric grease. Sea-Doo's yearly table inspects the ignition components, the electrical harness routing, modules and software updates, and the control switches and lighting. Kawasaki's list checks that the throttle, steering and reverse don't bind or stick, and that the throttle and reverse levers return fully when released.

Then test that the engine stops when it should, as each maker's pre-ride check does. Yamaha's 2026 manuals have you start the engine and stop it with the start/stop switch (a separate engine stop switch on the SuperJet), then restart it and pull the engine shut-off cord (lanyard) to make sure it stops immediately. The 2026 VX manual says to replace a damaged cord and never to repair it or tie it together. Sea-Doo's 2026 guides run the same test with the tether cord, say to replace a tether cord whose cap is loose or won't stay on the switch, and say not to use the watercraft if either method fails to stop the engine. Keep to the out-of-water limits in the next section while you test on land.

Engine flush and first start

Every maker limits how long the engine may run out of the water, and each gives its reason: Yamaha's 2026 manuals say the engine could overheat, Kawasaki's 2026 STX manual says overheating can damage the engine and exhaust system, and BRP's 2026 guides say the exhaust needs cooling water and the drive line seal has no cooling when the craft is out of the water. Yamaha's 2022 season article recommends a trial run on a flush hose with the factory-recommended attachment before you take the craft to the water, and says that first run also clears out the fogging oil that has coated the engine's internals since fall.

Important

Out-of-water limits, maker by maker

Yamaha's 2026 manuals: no more than 15 seconds without supplying water, and (all but the SuperJet manual) not over 4,000 r/min on land, or the engine could overheat. Kawasaki's 2026 STX manual: no more than 15 seconds at a time out of the water, never at maximum speed. Its flushing procedure is the longer run: with a garden hose connected, the engine idles for several minutes with the water running. Sea-Doo's 2026 guides: never run the engine without supplying water to the exhaust system, and never longer than 2 minutes. BRP's owner FAQ is stricter: it says never to run the motor out of the water, except to flush after riding in salt water, and then for no more than 30 seconds. Where these differ from your manual, follow the manual.

First start after storage, step by step

  1. Step 1: Uncover it, open it up and air it out

    Take the cover off and remove the seat (BRP says to remove the access cover on a Spark). Yamaha's 2026 manuals say to leave the engine compartment open for a few minutes so fuel vapors can escape. Kawasaki's 2026 STX manual opens the front hatch cover, removes the seats and opens the inspection vent hatch for several minutes. Don't start the engine if you smell gasoline or find a leak, and run it only in a well-ventilated area, never indoors: BRP and Kawasaki both warn that the exhaust contains carbon monoxide.

  2. Step 2: Check the oil, then connect the hose

    With the craft level, check the oil as described above (a Sea-Doo's check itself uses the flush hose and a short run). Then fit a garden hose to your maker's flush connection, without turning the water on yet. Yamaha's 2026 VX manual has the garden hose adapter push and twist onto the flushing hose connector. Sea-Doo's GTI, GTR and WAKE guide uses the connector at the rear of the craft. Kawasaki's 2026 STX manual uses the auxiliary water supply port under the rear seat, with a screw-in hose fitting.

    Uncovered jet ski on its trailer in a sunny driveway with a garden hose connected at the stern
  3. Step 3: Start the engine, then turn on the water

    All three makers use this order. Yamaha's 2026 VX manual says to turn the water fully on immediately after the engine starts so it flows continually from the jet thrust nozzle (the SuperJet manual opens it gradually instead), and never to supply water while the engine is stopped, because it could flow back through the muffler into the engine. Kawasaki gives the same warning about water flowing back through the exhaust pipe, and says to adjust the flow until a little trickle comes out of the bypass outlet on the right side of the hull. BRP says to open the tap immediately after starting, to prevent overheating. If the engine won't start, Yamaha's 2026 VX manual and Kawasaki's 2026 STX manual both say to let go of the start button after 5 seconds and wait 15 seconds before trying again.

  4. Step 4: Keep the run short and watch for leaks

    Kawasaki's Removal from Storage list runs the engine for 15 seconds and checks for fuel, oil and exhaust leaks, which must be repaired. Sea-Doo's GTI, GTR and WAKE guide flushes for 90 seconds at idle, and the Spark guide for about 20 seconds at a fast idle of 4,000 to 5,000 RPM, both making sure water flows out of the jet pump. Yamaha's 2026 VX manual idles for about 3 minutes during the flush, and says to turn the water off at once if the engine stops. Stay within your maker's limit and the run time in your manual.

  5. Step 5: Turn the water off before the engine

    Yamaha (2026 VX manual): turn the water off, squeeze and release the throttle lever quickly for 10 to 15 seconds to discharge the remaining water, then stop the engine. Sea-Doo: close the tap, run the engine at 5,000 RPM for 5 seconds, then stop it; BRP says always to close the tap before stopping the engine. Kawasaki: turn the water off with the engine idling, rev it a few times to clear water out of the exhaust, then switch off.

  6. Step 6: Close it up, launch and check again

    Refit the seats and make sure they lock in place, which is the last step on Kawasaki's list. On the water, start the engine only where it's deep enough: Yamaha's 2026 manuals say at least 60 cm (2 ft) from the bottom of the craft, Sea-Doo's 2026 guides at least 90 cm (3 ft) under the lowest rear of the hull with everyone aboard, and Kawasaki's 2026 STX manual at least 0.8 m (2.6 ft). Then run the after-launch checks: Yamaha looks for water coming out of the cooling water pilot outlet while the engine runs, and Sea-Doo checks the information center, the iBR brake and reverse system and, if fitted, the VTS trim.

For launching, riding basics and what to do once you're on the water, see our complete guide to jet skiing.

Hull and trailer safety check

Hull, pump and drain plugs

Yamaha's 2026 pre-operation checklist covers the outside of the craft: check the hull and deck for damage, and make sure the jet intake isn't damaged or clogged with weeds or debris. Sea-Doo's 2026 guides inspect the hull for cracks and the ride plate and intake grate for damage, and clear out anything that could restrict the water flow. BRP's 2023 summer-prep article adds two quick visual checks: replace the sacrificial anode if it's worn more than halfway, and look over the wear rings and impeller for deep scratches, nicks or unusual grooves. Signs of water in the engine compartment, it says, are a reason to contact your Sea-Doo dealer.

Next, the drain plugs. Yamaha's 2026 manuals have you remove the stern drain plugs, check the plugs and their O-rings for damage, clean any dirt or sand off the threads and O-rings, then tighten the plugs until they stop; otherwise, Yamaha warns, water may flood the engine compartment and the craft could submerge. Sea-Doo says to make sure the bilge drain plugs are secured before launching, and Kawasaki's 2026 Removal from Storage list checks that the drain screws in the stern are tight. Kawasaki's list also has you check that the fire extinguisher has a full charge.

Cleaning the craft belongs here too. Yamaha's 2022 season article suggests a wash-and-wax product for the hull and a vinyl cleaner and conditioner for the seat, avoiding vinyl "protectant" products that can make the seat slippery. BRP's summer-prep article recommends its own XPS Wash & Wax.

Trailer

The trailer sat all winter too. BoatUS's spring commissioning checklist (2022 edition) gives it these checks:

  • Inspect the tire treads and sidewalls for cracks or worn tread, and check the air pressure, including the spare's.
  • Inspect the wheel bearings and repack them as needed.
  • Test all the lights and replace broken bulbs or lenses.
  • Check that the winch works properly, and inspect the hitch chains.
  • Look over the frame and axles for rust; sand and paint it so it doesn't spread.
  • Inspect the brakes and the brake fluid reservoir.

Under paperwork, the same checklist reminds you to make sure the registration and trailer tags are current. Discover Boating's trailering checklist, which credits BoatUS for its content, adds detail: check tire pressure while the tires are cold; grease on the inside of the fenders means a bearing seal is bad; make sure the rollers turn easily and look for worn bunk carpet; and have someone stand behind the trailer while you test the lights and turn signals. On the road, it suggests touching the hubs when you stop; it calls hubs that feel excessively hot the leading warning sign that the bearings are losing grease and overheating, or that a brake pad is engaged. BRP's inspection checklist covers the hookup: winch strap and transom straps secure and tight, and the safety pin, working lights and safety chains properly connected. For the full routine, see how to trailer a jet ski.

Hand checking the tread of a galvanized jet ski trailer tire on a sunny driveway

How to de-winterize a Yamaha WaveRunner

Yamaha's nine 2026 U.S. owner's/operator's manuals have no spring section. Their pre-operation checklist is split into pre-launch checks done on land and post-launch checks done in the water with the engine running, and the manuals say to make those checks each time the watercraft is used. After storage, start there. Yamaha's 2022 article "Getting Your PWC Ready for the Season" adds seven spring steps, in this order:

  1. Spring cleaning: get the craft out from under its cover, take off the seat and inspect the engine compartment, the fuel and water lines and the electrical connections.
  2. Battery maintenance: clean the case and terminals, connect the cables positive first and negative last, and coat the terminals with dielectric grease.
  3. Corrosion protection: a silicone anti-corrosion spray on the top and sides of the engine, and a heavier inhibitor, such as Yamaha's Yamashield, on the lower parts and on underwater aluminum such as the pump and ride plate.
  4. A fresh coat: wash and wax the exterior and condition the seat.
  5. A trial run on a flush hose: start the engine before turning on the water, and turn the water off before stopping the engine.
  6. Fuel: if it wasn't conditioned for storage, empty the tank and refill. For gas you'll use within a week of buying it, the article says stabilizer isn't needed and suggests a continual-use treatment such as Yamaha's Engine Med RX at every fill-up.
  7. Lessons learned: next fall, change the oil before storage, not after.

Two more Yamaha specifics. The 2026 VX manual's periodic maintenance chart, which covers the spark plugs, fuel and cooling water hoses and the battery, is for a Yamaha dealer to perform. And on land, Yamaha's 2026 manuals limit the engine to 15 seconds without water; all but the SuperJet manual also cap it at 4,000 r/min. For the fall side of the job, see how to winterize a Yamaha WaveRunner.

How to de-winterize a Sea-Doo

Each 2026 Sea-Doo operator's guide we checked (GTI, GTR and WAKE; GTX; RXT-X 325; Spark; Wake Pro; FishPro Sport) ends its storage chapter with the same preseason note: do it together with the maintenance schedule, perform every task in the Every Year or 100 Hours table, and have it done by an authorized Sea-Doo dealer, a repair shop or a person of your own choosing. BRP adds that a dealer isn't required but is recommended for the preseason preparation, and it recommends an annual safety inspection. For the GTI, GTR and WAKE with Rotax 1630 ACE engines in regular use, that yearly table lists:

Sea-Doo's Every Year or 100 Hours tasks (2026 GTI, GTR and WAKE)

Spark plugs, every 2 years or 200 hours, the supercharger inspection and a propulsion inspection with lubrication sit in that table's two-year column, and the coolant is replaced every 5 years or 300 hours. The Spark guide's table is similar but puts the engine rubber mounts in the two-year column. BRP's 2023 summer-prep article runs in this order: spark plugs, battery, sacrificial anode, wear rings and impeller, oil and filter, wash and wax, then a refresher run through the pre-ride checklist in your operator's guide. Two Sea-Doo rules bear repeating: never charge or boost the battery while it's in the craft, and never run the engine out of the water without water to the exhaust, or for longer than 2 minutes. For the storage side, see how to winterize a Sea-Doo.

Kawasaki Jet Ski notes

Kawasaki's 2026 STX 160LX/STX 160X owner's manual has a Removal from Storage section, which it introduces as the steps needed to put the watercraft back in service after a storage period. The 2022 STX 160 manual has the same list in the same order, with small differences: it checks the shift mechanism instead of the reverse (and only the throttle lever's return), has you put the shift lever in R (Reverse) before checking the cooling and bilge hoses, and vents the engine compartment through the front storage lid and seats. Kawasaki says to see your Kawasaki dealer for this service or do it yourself, and its maintenance chapter says that work beyond the pre-ride and end-of-day checks should be done by qualified technicians. The 2026 list:

  1. Carry out all the recommended lubrication procedures.
  2. Check that the throttle, steering and reverse don't bind or stick; the throttle and reverse levers must return fully when released.
  3. Check the spark plugs.
  4. Check all rubber hoses, and the cooling and bilge hoses, for weathering, cracking or looseness.
  5. Check that the drain screws in the stern are securely tightened.
  6. Clean the battery terminals, charge the battery if necessary, and install it.
  7. Check the fire extinguisher for a full charge.
  8. Fill the fuel tank and close the filler cap securely.
  9. Before starting, open the front hatch cover, remove the seats and open the inspection vent hatch for several minutes to vent the engine compartment.
  10. Check for fuel leaks and repair any.
  11. Check the engine oil level and top up with the specified oil if needed.
  12. Start the engine and run it for 15 seconds, checking for fuel, oil and exhaust leaks; any leak must be repaired.
  13. Install the seats and make sure they're locked in place.

Kawasaki drains the fuel tank for storage, and filling it is on this list. Its out-of-water notice: never more than 15 seconds at a time, and never at maximum speed. For the storage side, see how to winterize a Kawasaki jet ski.

Cover off for the season, back on between rides

The cover is the first thing to come off in spring; Yamaha's 2022 season article starts by getting the craft out from under it. The Weatherproof Shield comes with a mesh storage bag to keep it in until you need it.

During the season the cover still has work to do. Yamaha's 2021 Maintenance Matters guide advises protecting a WaveRunner from the elements with a cover when it isn't in use or is being trailered. Kawasaki's 2026 STX 160 manual's storage notes add that water left in the footwells can make the paint bubble and peel and the deck mat peel off, that it can collect there even under a cover if the craft is outside, and that a craft left on a trailer should have the tongue raised so water can't pool. For where to keep the craft in the off-season, see jet ski winter storage.

For the trailer and the driveway, ours is the Weatherproof Shield: 600D solution-dyed polyester with a PU coating, water-resistant, with an elastic hem cord, built-in buckles and straps, air vents to aid trailering, an extra strap set and a mesh storage bag. It has a Lifetime warranty (see our warranty page). Whether to tow with it on is covered in can you trailer a jet ski with the cover on. For a garage, the Satin Shield is a stretch cover of 85% polyester and 15% spandex with a sheared fleece interior, made for indoor storage only, with a satin storage bag included.

Trailerable Cover

AllGuard Weatherproof Shield Jet Ski Cover (Trailerable)

For riding season on the trailer or in the driveway: 600D PU-coated polyester, water-resistant, with built-in buckles and straps and air vents to aid trailering.

4 colors: Blue / Black, Gray / Black, Red / Black, Yellow / Black

  • Under 90 inP0
  • Under 102 inP1
  • Under 115 inP2
  • Under 125 inP3
  • Under 135 inP4
  • Under 145 inP5
  • Up to 160 inP6

Lifetime Warranty

Both covers are sized by the craft's overall length, not by make or model. Measure yours or look up its published overall length, then match it in the jet ski cover size guide; the Satin Shield goes up to 138 inches. You can also browse all our jet ski covers.

Find your cover size

Measure your ski's overall length, then match it to a size.

Open the size guide

De-winterizing checklist

Run through this before the first trip to the ramp. It's a summary; your owner's manual has the full procedure for your model and year.

Ready for the first ride

De-winterizing FAQ

Yes, if it was stored for the off-season. Sea-Doo's 2026 operator's guides pair storage with a preseason preparation, Kawasaki's 2022 and 2026 STX 160 owner's manuals have a Removal from Storage list to put the craft back in service, and Yamaha's 2026 manuals call for pre-operation checks each time the watercraft is used. Yamaha's 2022 season article adds that a proper fall winterization means a quicker return to the water, not that the craft needs no attention before its first splash.

Sources

  1. 2026 WaveRunner VX-C/VX/VX Deluxe/VX Cruiser/VX Limited Owner's/Operator's Manual, U.S.A. Edition (LIT-18626-15-77): Pre-operation checks; Care and storage; Periodic maintenance chart (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2026 model year; viewed 2026-10-27
  2. 2026 WaveRunner SuperJet Owner's/Operator's Manual, U.S.A. Edition (LIT-18626-15-71) (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2026 model year; viewed 2026-10-27
  3. 2026 WaveRunner FX HO/FX Cruiser HO Owner's/Operator's Manual, U.S.A. Edition (LIT-18626-15-73) (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2026 model year; viewed 2026-10-27
  4. Getting Your PWC Ready for the Season (opens in a new tab)Yamaha WaveRunners (Yamaha Motor Corporation, U.S.A.) · 2022-03-16
  5. How to Perform a Pre-Ride Check of Your WaveRunner (opens in a new tab)Yamaha WaveRunners (Yamaha Motor Corporation, U.S.A.) · 2021-07-27
  6. Maintenance Matters (opens in a new tab)Yamaha WaveRunners (Yamaha Motor Corporation, U.S.A.) · web version of the 2021 guide; viewed 2026-10-27
  7. GTI, GTR and WAKE Series 2026 Operator's Guide: Pre-Ride Inspection; Maintenance Schedule; Maintenance Procedures; Storage and Preseason Preparation (opens in a new tab)BRP · MY2026 guide; viewed 2026-10-27
  8. Spark Series 2026 Operator's Guide: Maintenance Schedule; Flushing the Exhaust System; Storage and Preseason Preparation (opens in a new tab)BRP · MY2026 guide; viewed 2026-10-27
  9. GTX Series 2026 Operator's Guide: Storage and Preseason Preparation (opens in a new tab)BRP · MY2026 guide; viewed 2026-10-27
  10. Prepping your Sea-Doo for Summer Fun (opens in a new tab)BRP (Sea-Doo) · 2023-03-15
  11. Can you run the motor of your Sea-Doo out of the water? (opens in a new tab)BRP (Sea-Doo) · undated; viewed 2026-10-27
  12. How to inspect your Personal Watercraft? (opens in a new tab)BRP (Sea-Doo) · undated; viewed 2026-10-27
  13. JET SKI STX 160LX / STX 160X Owner's Manual, JN1500F/H (2026), item 99814-0205: Removal from Storage; Maintenance and Adjustments (opens in a new tab)Kawasaki Motors Corp., U.S.A. · 2026 model year; viewed 2026-10-27
  14. JET SKI STX 160 Owner's Manual, JT1500R/S/T (2022), item 99803-0202: Removal from Storage (opens in a new tab)Kawasaki Motors Corp., U.S.A. · 2022 model year; viewed 2026-10-27
  15. Spring Commissioning Checklist (2022/v3) (opens in a new tab)BoatUS · 2022-03-09
  16. Your Ultimate Trailering Checklist (content courtesy of BoatU.S.) (opens in a new tab)Discover Boating (NMMA) · undated; viewed 2026-10-27

Find Your Size

Measure your jet ski bow to stern in a straight line, then enter the length in inches.

  1. Under 90 inP0
  2. Under 102 inP1
  3. Under 115 inP2
  4. Under 125 inP3
  5. Under 135 inP4
  6. Under 145 inP5
  7. Up to 160 inP6
Full Size Guide

In inches. Decimals are fine.

Covers for Your Jet Ski

All Covers