Maintenance

How to Clean and Wax a Jet Ski

The Sea-Doo, Yamaha and Kawasaki documents cited here all wash the craft with fresh water, then differ on soap, wax and the engine-bay rinse. Here's what each says, with the cautions.

By Alex Quinn 20 min read

A hand in a soft wash mitt spreading soap suds along the glossy side of an uncovered jet ski on its trailer in a shaded driveway

To clean a jet ski, rinse the hull, deck and jet pump with fresh water, wash with a mild soap or detergent where your maker calls for one, rinse again and dry the craft. Sea-Doo's 2026 operator's guides say to wash the body and hull with a soap and water solution (use only mild detergent) and rinse thoroughly with fresh water. Yamaha's 2026 owner's manuals say to wash down the hull, deck and jet pump with fresh water, then wipe them with a dry cloth. Kawasaki's 2026 STX 160 owner's manual says to wash the hull, deck, water intake and propulsion system with fresh water, and to use only a mild detergent in water to wash the watercraft.

Waxing is a separate job, and the makers don't time it the same way. Sea-Doo's guides call for a good quality marine wax without a schedule, Yamaha's 2026 manuals put waxing in their long-term storage steps, and the Kawasaki 2026 manuals cited here name no wax at all. Below: the wash, what each maker says not to use (dish soap included), stains and marine growth, waxing, the engine-bay rinse, the seat and faded plastic. For the rest of the routine, see our jet ski maintenance tips; for the flush itself, which differs by maker, see how to flush a jet ski.

Note

Your owner's manual has the final say

Cleaning steps, cautions and the products each maker names differ by make and model. The documents quoted here are Sea-Doo's 2026 GTI, GTR and WAKE and 2026 Spark operator's guides, Sea-Doo's 2020 Clean and Protect page and BRP's 2026 winterizing article; Yamaha's 2026 VX and SuperJet owner's manuals, its 2021 Maintenance Matters guide and its 2022 season-prep article; Kawasaki's 2026 STX 160 and Ultra 310LX owner's manuals; and two undated Discover Boating pages. Products named below are the sources' own suggestions, not ours. Where this guide and your manual differ, follow your manual.

How to clean a jet ski hull and deck

Each maker's documents include a wash step, and they differ on soap. Here is what each says to wash with, and what comes next.

From each maker's own documents, read 2026-10-27 to 2026-10-31. Your model's manual may differ.
MakerDocumentWash withThen
Sea-Doo2026 GTI, GTR and WAKE operator's guide, p. 168 (same text in the 2026 Spark guide)Body and hull with a soap and water solution, mild detergent onlyRinse thoroughly with fresh water; remove marine organisms from the inside and outside of the hull
Yamaha 20262026 VX owner's manual, p. 101 (same wash steps in all nine 2026 U.S. manuals)Hull, deck and jet pump with fresh water; the steps name no soapWipe the hull, deck and jet pump with a dry cloth
Yamaha 20212021 Maintenance Matters guide, pp. 8 and 12-13Clean water over the entire exterior, then mild soap or a mild, marine-specific cleaning agent such as Yamaclean Pro-Wash spray and a soft clothRinse again; a good quality chamois afterward
Kawasaki2026 STX 160 owner's manual, pp. 143 and 152 (same cleaning NOTICE in the 2026 Ultra 310LX manual)Hull, deck, water intake, propulsion system and speaker (equipped models) with fresh water; only a mild detergent in waterAt storage: wash the exterior and dry it thoroughly

Beyond the table, BRP's 2026 winterizing article for Sea-Doo owners, in its final storage step, says to wash the hull and deck with a marine-safe cleaner and remove salt, grime and organic buildup. Yamaha's 2021 guide also says not to spare the hose when returning from a trip, particularly in salt water, and to wash the trailer too; see jet ski trailer maintenance for the trailer side.

Clean, drain and dry at the ramp

Sea-Doo's 2026 operator's guides start before you leave the water. Under "Clean, Drain and Dry", they say to inspect and remove any visible plants, fish, animals, mud or other debris from the watercraft (including the hull, intake grate and jet pump nozzle), the trailer and your water sports gear before leaving the water body, then to let everything dry completely (for 5 days or more, refer to local laws) before visiting any other body of water. The same guides ask owners to make sure fuel, oil or cleaning solutions don't drain into the waterways.

Deck mats and footwells

For the deck mats, which Sea-Doo's 2026 guides call carpets, the guides name 3M Citrus Base Cleaner or an equivalent. Kawasaki's 2026 STX 160 manual warns that water left in the footwells can cause the paint to bubble and peel, and the mat to peel off the deck. Draining is covered in water in a jet ski hull.

The steps below combine those wash steps, with the source of each named. Skip any step your own manual doesn't include.

Wash a jet ski hull and deck

  1. Step 1: Take it out of the water

    Yamaha's 2026 owner's manuals say to take the watercraft out of the water after using it, clean it and store it.

  2. Step 2: Clear the hull at the ramp

    Remove visible plants, animals, mud and debris from the hull, intake grate, jet pump nozzle and trailer before you leave the water body (Sea-Doo).

  3. Step 3: Rinse with fresh water

    Rinse the hull, deck and jet pump with fresh water (Yamaha 2026), plus the water intake and propulsion system (Kawasaki). Avoid spraying with great force near speakers (Kawasaki).

  4. Step 4: Wash with a mild cleaner

    Use a mild detergent (Sea-Doo; Kawasaki) or a mild soap and a soft cloth (Yamaha 2021), and no liquid dish soap or household detergent (Yamaha 2021). Check what your maker says not to use, and keep cleaning solutions out of the waterway (Sea-Doo).

  5. Step 5: Rinse again

    Rinse thoroughly with fresh water (Sea-Doo; Yamaha 2021).

  6. Step 6: Dry it

    Wipe the hull, deck and jet pump with a dry cloth (Yamaha 2026) or a good quality chamois (Yamaha 2021).

  7. Step 7: Protect the metal

    Yamaha's 2026 VX manual says to spray metallic parts of the hull, deck and engine with a rust inhibitor such as Yamalube Silicone Protectant & Lubricant to minimize corrosion. Kawasaki's 2026 STX 160 manual, at storage, says to lightly spray exposed metal parts with a penetrating rust inhibitor such as WD40 or BEL-RAY 6 in 1.

  8. Step 8: Wax when your maker says to

    The makers place waxing at different times, and Kawasaki names none; see the waxing section below.

What not to use on a jet ski

Sea-Doo's 2026 operator's guides give the longest list. In a NOTICE, they say never to clean with XPS S4 Heavy Duty Cleaner (one of BRP's own products), strong detergent, a degreasing agent, ammonia, acetone or other ketones, alcohol, toluene or other aromatic solvents, chlorinated solvents, mineral spirits, paint thinners or petroleum-based products.

Kawasaki's 2026 STX 160 and Ultra 310LX owner's manuals give a reason in their cleaning NOTICE: harsh cleaning solvents may attack the surface or smear the colors. To preserve the finish, Kawasaki says to use only a mild detergent in water. For a semi-gloss finish, the STX 160 manual says always to use a mild neutral detergent and water, warns that the semi-gloss effect may be lost if the finish is excessively rubbed, and says to consult an authorized Kawasaki dealer if in any doubt. The manual doesn't say which models or panels have a semi-gloss finish.

Sea-Doo's 2020 Clean and Protect page names Sea-Doo's finishes as Acrylic and Thermofil, and says the XPS products it lists are safe to use on them. The 2026 manuals' care sections cited here don't name hull materials, so check your own manual for your craft's finish.

Can you use Dawn or dish soap on a jet ski?

Of the makers here, only Yamaha addresses dish soap. Its 2021 Maintenance Matters guide says not to use liquid dish soap or ordinary household detergents when washing your boat, because, in Yamaha's words, they remove waxes and other protective coatings your boat needs; elsewhere the same guide says liquid dish soap can strip off important protectants. Sea-Doo's and Kawasaki's 2026 manuals don't mention dish soap. They call for a mild detergent, and Sea-Doo's never-use list includes strong detergent. None of these sources mentions Dawn by name.

Stains, waterline scum and marine growth

Sea-Doo's 2026 operator's guides say to remove marine organisms from the inside and outside of the hull. Yamaha's 2021 Maintenance Matters guide calls the pre-storage clean perhaps the best time to pull the craft out of the water and clean the hull as necessary, removing any marine growth or barnacles with a thorough washing.

Two makers tie hull wear to time in the water. Yamaha's 2026 owner's manuals say leaving the watercraft in the water for extended periods will accelerate the rate of normal deterioration of the jet pump and hull, and name marine organisms and corrosion among the conditions that can shorten the life of many components. Kawasaki's 2026 STX 160 manual says prolonged immersion will cause the hull paint to bubble and peel. More on that in can you leave a jet ski in the water.

Heavy scum and waterlines

Sea-Doo's 2020 Clean and Protect page says a craft stored in water for long periods can collect heavy scum, algae, waterlines and rust, and describes its XPS Sea-Doo Hull Cleaner for that job. Its steps: follow the product instructions carefully; wear gloves and protective eyewear; if the craft is stored on a trailer or rack, be sure to protect it from the product before cleaning; spray the cleaner directly on the hull; wait 2-4 minutes; scrub the treated area with a brush; then immediately rinse thoroughly with water, ideally with a pressure washer. That pressure-washer line is about rinsing this product off the hull. Sea-Doo's 2026 guides say never to use a high-pressure washer in the bilge.

Sea-Doo's own documents disagree on degreasers. The 2026 guides list a degreasing agent among the products never to clean with, yet name a Sea-Doo cleaner-and-degreaser for stains on the seat and fiberglass on the same page, and the 2020 page suggests a Sea-Doo degreaser for lighter waterline stains. We don't give degreaser advice here: follow the current operator's guide for your model.

If you find damage while you clean, Sea-Doo's 2026 guides say to contact your authorized Sea-Doo dealer for any repairs to body components or the hull. BRP's 2026 winterizing article includes inspecting the hull for scratches or cracks in its final cleaning step.

How to wax a jet ski

Should you wax your jet ski? Sea-Doo and Yamaha both include a wax step, and the Kawasaki 2026 manuals cited here name no wax or polish. None of the sources gives a waxing interval that holds across makers, and they place the job at different times.

From each maker's own documents, read 2026-10-27 to 2026-10-31. No source here gives a cross-maker schedule.
MakerDocumentWax stepWhen
Sea-Doo2026 GTI, GTR and WAKE guide, p. 169; 2026 Spark guide, pp. 132-133Apply a good quality marine wax to the bodyNo timing given
BRP (Sea-Doo web)How to Winterize Your PWC, dated 6/9/26Dry thoroughly and apply a protective coat of wax if desiredAt storage, if desired
Yamaha 20262026 VX owner's manual, p. 103 (same step in all nine 2026 U.S. manuals)Wax the hull with a non-abrasive wax such as Yamalube Professional PolishLong-term storage
Yamaha 2021Maintenance Matters guide, pp. 9 and 22-23'Wash and wax'; where applicable, a coat of sealant or waxPost-operation list; before extended storage
Yamaha 2022Getting Your PWC Ready for the Season, dated 03.16.2022A thorough wash and wax in the fall; a wash n' wax product to freshen upFall, then again at season prep
Kawasaki2026 STX 160 and Ultra 310LX owner's manualsNo wax or polish namedAt storage: wash, dry thoroughly, rust inhibitor on exposed metal
A hand applying wax with a microfiber pad to the glossy upper side of a jet ski hull

Sea-Doo's 2020 Clean and Protect page goes further, with its own XPS products. It describes XPS Wash and Wax as a one-step foaming formula that cleans and finishes with a protective wax coating, and gives the mix: 30 mL (1 oz.) of cleaner for every 4 L (1 gal.), scrubbed on with a car wash mitt or soft brush, then rinsed with water and dried thoroughly. For a separate coat, it describes XPS Marine Spray Wax with Polymer as a sealant that, Sea-Doo says, protects the surface and prevents algae, rust and other water contaminants from finding a home on the hull and deck. The page also suggests XPS Spray Wax on high-gloss surfaces, for protection from the elements that it says includes UV rays.

Sea-Doo's spray-wax steps (2020)

  1. Make sure the craft has been properly cleaned first: Sea-Doo says you don't want to seal in any stains or grime.
  2. Spray directly on the surfaces.
  3. Allow it to dry for a few seconds.
  4. Wipe with a clean, dry microfiber cloth.

Sea-Doo's 2020 page adds that the product can be applied in direct sunlight, but not to hot surfaces. Yamaha's 2026 storage step, by contrast, says to clean the craft first and names no application method for its wax.

Wax and non-skid surfaces

None of the PWC makers' documents here gives a step for waxing footwells or traction mats. Discover Boating, writing about boats in general, says molded-in non-skid fiberglass can't be treated like other fiberglass parts: applying wax would make it slippery, defeating the purpose of a non-skid surface. Sea-Doo's 2020 spray-wax description mentions the deck, so check your manual before you wax anything you stand on.

How to clean a jet ski engine bay

Sea-Doo, Yamaha and Discover Boating rule out high pressure, Kawasaki says to cover the air intake hole and not spray electrical equipment, and the sources differ on when to rinse. Here is each source's trigger, pressure rule and routine.

From each source's own document, read 2026-10-27 to 2026-10-31. Discover Boating writes for personal watercraft in general.
SourceWhen to rinseWater pressureBefore and after
Sea-DooAfter foul water and particularly salt water (2026 guides, p. 168)Low pressure only, such as a garden hose; never a high-pressure washerLet the engine cool first
Yamaha 2026Part of its cleaning steps (2026 VX manual, p. 101)A small amount of water; no high-pressure waterSeats off (SuperJet: hood); drain, wipe dry, air dry completely before refitting
Yamaha 2021If salt build-up is a problem or the engine contacted salt water (Maintenance Matters, p. 8)Hose on low pressure, not a spray attachment; not around the air intakeEngine and seat completely air dry before the seat goes back
KawasakiWhen used at sea (2026 STX 160 manual, pp. 142-143)Cover the air intake hole; don't spray electrical equipmentSeats and engine cover off; drain screws if water has accumulated; wipe dry
Discover BoatingAfter salt-water use (all PWC, undated page)Garden hose; never a pressure washerEngine cool; bilge plug out; water-displacing lubricant; seat off to dry
A forearm holding a garden hose with a gentle trickle rinsing the stern of a jet ski on its trailer, the seat set aside

Sea-Doo's 2026 operator's guides give the reason for their low-pressure rule: high pressure can cause damage to electrical or mechanical systems.

Yamaha's 2026 VX owner's manual makes the rinse part of its "Cleaning the watercraft" steps. Its NOTICE gives the reason for the no-high-pressure rule: severe engine damage could result. In its order, the outside wash and the rust inhibitor on metal parts come before the compartment air-dries completely and the seats go back. The VX steps also say to rustproof the internal engine components if the craft will be stored for a week or more; that procedure is in how to winterize a jet ski.

Yamaha's 2021 Maintenance Matters guide sets a condition: if salt build-up has become a problem, or the engine has been in direct contact with salt water, it says it's okay to gently rinse portions of the engine with clean, fresh water, using a hose on low pressure (not a spray attachment) and not rinsing around the air intake area. It adds rinsing out the inside of the seat. The guide then has you spray the entire dry engine with a protectant (Yamashield for salt-water environments, silicone spray for fresh water), including the electrical connections. Its post-operation list separately says to rinse the engine compartment with fresh water and Yamaclean Pro-Wash Spray, and says Salt-Away, a third-party product, will greatly reduce the corrosive effects from salt exposure.

Kawasaki's 2026 STX 160 owner's manual puts the rinse in its end-of-the-day checklist, and its NOTICE gives the reason for covering the air intake hole and not spraying electrical equipment: water can enter the engine through the air box and cause severe engine damage and shorts in electrical equipment. When the craft is ready for storage, Kawasaki says to remove the seats to aid air circulation and prevent condensation from forming.

Discover Boating, writing for personal watercraft in general, explains the salt-water case: a salty mist can enter the engine compartment through the ventilation system and cause corrosion on the throttle linkage, electrical connections and other components. It rules out a pressure washer because, it says, too much pressure can force water past seals on electrical connectors.

The jet pump

Sea-Doo's 2026 guides, in their storage chapter, say to remove the tether cord from the engine cut-off switch before cleaning the jet pump area, to prevent unexpected engine starting, and that the engine must not be running. Then rinse the jet pump by spraying water through its inlet and outlet openings, and spray an anti-corrosive product, such as XPS Anti-corrosive lubricant or equivalent, on the propulsion system parts. Yamaha's 2026 manuals wash the jet pump down with the hull and deck, and Kawasaki's 2026 STX 160 manual includes the water intake and propulsion system in its fresh-water wash. Flushing is its own job, and what gets flushed differs by maker: see how to flush a jet ski.

Cleaning the seat

Sea-Doo's 2026 operator's guides suggest trying a white eraser on marks before applying a cleaning product to the seat, and say not to leave anything wet, like towels or swimsuits, or anything biological, such as food or leaves, on the seats, warning that permanent damage can occur. The makers' documents disagree about vinyl protectant on seats, and Yamaha's own documents differ, so we leave that to our guide on how to clean jet ski seats and remove mold.

Faded plastic: what the makers say

Yamaha's 2021 Maintenance Matters guide says WaveRunners are susceptible to damage from exposure to sun, rain, snow and dust, and lists plastic discoloring and hardening and painted or treated surfaces fading among the things routine precautions must guard against. Sea-Doo's 2026 operator's guides say never to leave the watercraft stored in direct sunlight.

For prevention, Sea-Doo's 2020 Clean and Protect page suggests one of its XPS products on non-painted textured surfaces, such as a Sea-Doo Spark, to prevent any potential color fading from the sun's rays, and says it can also be used on soft plastic parts like bumpers. It says to allow one to two hours for it to dry.

How do you make jet ski plastic look new again? None of the maker documents cited here gives a method for restoring faded, chalky or oxidized plastic, paint or gel coat; their advice is preventive. For keeping an outdoor craft out of the weather, see storing a jet ski outside.

Cover it once it's clean and dry

Two makers' storage steps stress drying. Kawasaki's 2026 STX 160 manual says to wash the exterior and dry it thoroughly, and Yamaha's 2021 Maintenance Matters guide says to make sure any item or area is bone-dry before closing it up or sealing it off.

Our Weatherproof Shield is a water-resistant cover sold as trailerable: 600D solution-dyed polyester with a PU coating, an elastic hem cord, built-in buckles and straps, and air vents to aid trailering, with a mesh storage bag and an extra strap set. The Satin Shield is our indoor cover, 85% polyester and 15% spandex with a sheared fleece interior (Satin storage bag included). Covers are sized by overall length, and the size guide matches yours to a size. The Weatherproof Shield carries a Lifetime warranty. See all our jet ski covers. To wash the cover itself, see how to clean and care for your cover.

Red-and-black Weatherproof Shield cover draped loosely over a jet ski on its trailer in a freshly washed driveway

Trailerable Cover

AllGuard Weatherproof Shield Jet Ski Cover (Trailerable)

For the clean, dry craft: a water-resistant, trailerable cover with air vents to aid trailering, an elastic hem cord and built-in buckles and straps. Sized by overall length.

4 colors: Blue / Black, Gray / Black, Red / Black, Yellow / Black

  • Under 90 inP0
  • Under 102 inP1
  • Under 115 inP2
  • Under 125 inP3
  • Under 135 inP4
  • Under 145 inP5
  • Up to 160 inP6

Lifetime Warranty

Jet ski cleaning checklist

Use this list when you clean the craft. It gathers the items above from the Sea-Doo, Yamaha and Kawasaki documents and Discover Boating; your own manual decides which ones apply.

Before you call it clean

Jet ski cleaning FAQ

Rinse the hull, deck and jet pump with fresh water, wash with a mild detergent or soap where your maker names one, rinse again and dry it. Sea-Doo's 2026 operator's guides say to use a soap and water solution with only mild detergent and rinse thoroughly with fresh water. Yamaha's 2026 owner's manuals wash the hull, deck and jet pump with fresh water and wipe them with a dry cloth. Kawasaki's 2026 STX 160 manual washes the hull, deck, water intake and propulsion system with fresh water. Rinse the engine bay only as your manual directs, at low pressure.

Clean, dry and ready to cover?

Covers go by your jet ski's overall length. Match yours in the size guide.

Open the size guide

Sources

  1. 2026 GTI, GTR and WAKE Series Operator's Guide: Clean, Drain and Dry (p. 44); Watercraft Care (pp. 168-169); Cleaning the Jet Pump (p. 170) (opens in a new tab)BRP (Sea-Doo) · 2026-10-31
  2. 2026 Spark Series Operator's Guide: Watercraft Care (pp. 132-133) (opens in a new tab)BRP (Sea-Doo) · 2026-10-31
  3. Doo It Right: Clean and Protect (web page dated 5/22/20) (opens in a new tab)BRP (Sea-Doo) · 2026-10-31
  4. How to Winterize Your PWC (Personal Watercraft) (web article dated 6/9/26): Final Cleaning and Storage (opens in a new tab)BRP (Sea-Doo) · 2026-10-27
  5. 2026 WaveRunner VX-C/VX/VX DELUXE/VX CRUISER/VX LIMITED Owner's/Operator's Manual, U.S.A. Edition, LIT-18626-15-77: Post-operation care (p. 100); Cleaning the watercraft (p. 101); Long-term storage (p. 103) (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2026-10-30
  6. 2026 WaveRunner SUPERJET Owner's/Operator's Manual, U.S.A. Edition, LIT-18626-15-71: Cleaning the watercraft (p. 64) (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2026-10-31
  7. Maintenance Matters: A Simple Guide for the Longevity of Your WaveRunner (2021): corrosion and rinsing (pp. 8-9); external appearance (pp. 12-13); protect against the elements (pp. 20-21); storage (pp. 22-23) (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2026-10-27
  8. Getting Your PWC Ready for the Season (web article dated 03.16.2022) (opens in a new tab)Yamaha WaveRunners (Yamaha Motor Corporation, U.S.A.) · 2026-10-27
  9. JET SKI STX 160LX / STX 160X Owner's Manual, JN1500F/H (2026): End of the Day Checklist (pp. 142-143); Cleaning (p. 152) (opens in a new tab)Kawasaki Motors Corp., U.S.A. · 2026-10-30
  10. JET SKI Ultra 310LX / 310LX-S Owner's Manual, JV1500A/B (2026): Cleaning (p. 159) (opens in a new tab)Kawasaki Motors Corp., U.S.A. · 2026-10-30
  11. How to Flush a Jet Ski, WaveRunner or Personal Watercraft (PWC): Rinsing Your Engine Bay (undated page) (opens in a new tab)Discover Boating (NMMA) · 2026-10-27
  12. How to Clean a Boat: Cleaning Boat Fiberglass (undated page; boats in general) (opens in a new tab)Discover Boating (NMMA) · 2026-10-31

Find Your Size

Measure your jet ski bow to stern in a straight line, then enter the length in inches.

  1. Under 90 inP0
  2. Under 102 inP1
  3. Under 115 inP2
  4. Under 125 inP3
  5. Under 135 inP4
  6. Under 145 inP5
  7. Up to 160 inP6
Full Size Guide

In inches. Decimals are fine.

Covers for Your Jet Ski

All Covers