Maintenance

How to Get Mold Out of Jet Ski Seats

Mold needs moisture, and moisture is the part you can most likely control. Here is how to clean mold off a vinyl jet ski seat without damaging it, where Sea-Doo, Yamaha, vinyl makers and boating groups disagree, and how to store the seat dry.

By Alex Quinn 17 min read

Gloved hands scrubbing soapy suds into a gray vinyl jet ski seat with a soft-bristle brush

Getting mold out of a jet ski seat takes four things: a gentle wash, the right cleaner for the vinyl, a thorough rinse and complete drying. The hard part is the cleaner. Marine-vinyl makers and boating groups don't agree on bleach, and the jet ski makers don't agree on vinyl protectant, so this guide sets out what each one says, the steps they share, and how to store the seat so mold has less to work with.

Your owner's manual comes first (Sea-Doo calls it the operator's guide). Where it and this guide differ, follow the manual. For the rest of the after-ride routine, see our jet ski maintenance guide.

Key takeaways

  • Start gentle: fresh water, mild soap and a soft brush or cloth, then rinse and dry.
  • Test any stronger cleaner on a hidden spot first.
  • Morbern and Naugahyde allow bleach diluted to 10% (Morbern only on vinyl it specifies as bleach-cleanable); Discover Boating and BoatUS Magazine say to avoid bleach on boat seats.
  • Never mix bleach with ammonia or cleaners that contain it (EPA, CDC).
  • Dry the seat completely before it goes back on the craft (Yamaha) or under a cover (Sea-Doo, Public Storage).

Why mold grows on jet ski seats

A 2002 fact sheet from the Chemical Fabrics & Film Association (CFFA), posted by the marine-vinyl maker Morbern, says mildew needs four things to grow: spores, food, warmth and moisture. Take away any one of them and the problem goes away. Moisture, it says, is the element you can most likely control, and even that is hard: marine upholstery may be dry when someone sits on it, but it is constantly exposed to rain, splashes and wet bathing suits.

The same fact sheet says the stains some of these organisms leave are typically pink, yellow, purple or black, and that a marine seat is more than its vinyl skin: the vinyl is usually attached to a backing fabric over urethane foam. Dirt carried in by wind or rain can work into seams and stitch holes, and growth that starts inside the cushion can stain the vinyl from beneath. Discover Boating makes the same point: once mold gets into the cushion, cleaning the surface may not stop it growing back from the inside.

Sea-Doo's 2026 operator's guide adds a simple rule: don't leave anything wet, such as towels or swimsuits, or anything biological, such as food or leaves, on the seat, because permanent damage can occur.

Before you start: protect yourself and the vinyl

The EPA's guide to mold recommends gloves and goggles without ventilation holes, and says that to limit how much mold you breathe in, you may want to wear an N-95 respirator. With a mild detergent, it says ordinary household rubber gloves will do; with bleach or a strong cleaner, it suggests gloves made of natural rubber, neoprene, nitrile, polyurethane or PVC. Work outdoors, or with the garage door open: the CDC's mold-cleaning tips say to open doors and windows while you work.

The EPA also notes that inhaling or touching mold or mold spores may cause allergic reactions in sensitive people, that molds can cause asthma attacks in people with asthma who are allergic to mold, and that mold exposure can irritate the eyes, skin, nose, throat and lungs. If you have health concerns, it advises talking to a health professional before you start.

Then protect the seat. A 2018 BoatUS Magazine article suggests asking the manufacturer of whatever you're cleaning for advice where possible, reading cleaner labels to make sure they're safe on that surface, and testing any product on a small, inconspicuous area first. The vinyl makers Morbern and Naugahyde give the same spot-test advice.

Important

Never mix bleach and ammonia

The EPA warns never to mix chlorine bleach with cleaning solutions or detergents that contain ammonia, because toxic fumes could be produced. The CDC says not to mix cleaning products at all. Rinse one cleaner off completely before you try another.

How to get mold out of a jet ski seat, step by step

These steps combine what Sea-Doo, Yamaha, Kawasaki, the vinyl makers and Discover Boating publish. Start with the mildest step, and move to a stronger cleaner only if mold is still there: Discover Boating advises against an aftermarket vinyl cleaner until mold or mildew appears that won't gently scrub away.

Removing mold and mildew from a vinyl jet ski seat

  1. Step 1: Set up somewhere airy

    Put the craft on its trailer or a stand, out of the water, outdoors or in a garage with the door open. Put on gloves and eye protection. Keep runoff out of the water: Sea-Doo's 2026 operator's guide asks owners to make sure fuel, oil and cleaning solutions don't drain into waterways.

  2. Step 2: Remove the seat if you can

    Yamaha's 2026 VX and Kawasaki's 2022 STX 160 owner's manuals both begin their cleaning steps by removing the seat, and your manual shows how on your model. With the seat off, you can reach the seams, the edges and the underside.

  3. Step 3: Rinse with fresh water at low pressure

    Rinse the seat with fresh water from a garden hose; Discover Boating's seat-care steps start with a freshwater rinse. Keep the pressure low, especially with the seat off: Sea-Doo says never to use a high-pressure washer on the bilge, and Yamaha's 2026 VX manual warns against high-pressure water on the engine and engine compartment.

    Garden hose with a gentle shower spray rinsing soap off a gray and black jet ski seat
  4. Step 4: Wash with mild soap and warm water

    Naugahyde's 2018 care sheet suggests a solution of 10% mild soap in warm water on a soft, damp cloth; Morbern's 2017 care sheet says most stains come off with warm, soapy water and clear-water rinses. Discover Boating's method is to soak and soap the seat, wait a few minutes for the grime to loosen, wipe gently, and repeat for several rounds rather than scrubbing hard.

  5. Step 5: Work the seams with a soft brush

    For stitching and textured vinyl, use a soft-bristle brush. Sea-Doo suggests a soft brush for stubborn dirt on seats, Morbern a soft brush for stubborn mildew, and Discover Boating warns against stiff, bristly brushes on boat seats.

  6. Step 6: Treat what's left with a vinyl-safe cleaner

    If mold is still visible, use a cleaner made for the job and follow its label: your craft maker's seat cleaner (Sea-Doo's 2026 operator's guide names its XPS All Purpose Cleaner and Degreaser for seat stains, and a 2020 Sea-Doo cleaning page says it treats mold and mildew), a dedicated marine-vinyl cleaner, or diluted bleach, only if your seat's maker or owner's manual approves it. The next section covers where the sources disagree.

  7. Step 7: Rinse repeatedly

    Rinse off every trace of cleaner with clean water. Morbern recommends repeated rinsing with clear water after any cleaning, and Naugahyde says to wipe away any remaining bleach with a water-dampened cloth. Don't leave a cleaner to dry on the vinyl.

  8. Step 8: Dry it completely

    Wipe the seat dry, then let it air-dry. Yamaha's 2021 maintenance guide says to stand a removed seat on end against a wall so water drains from the foam, and to make sure the seat and engine are completely air dry before the seat goes back on.

    Removed jet ski seat standing on end against a garage wall to drain and dry

Tip

Scuffs aren't mold

Sea-Doo's operator's guides suggest trying a white eraser on marks such as shoe scuffs before you use any cleaning product on the seat.

Bleach, vinegar and other cleaners: what to use

This is where the sources disagree most, so each view below is attributed. If your owner's manual or your seat's maker says something different, follow it.

Bleach. The vinyl makers allow it, diluted, with conditions. The CFFA fact sheet says observed mildew can be removed by washing with a dilute solution of household bleach in water, then rinsing and drying thoroughly. Morbern's care sheet, for its vinyls specified as bleach-cleanable, allows bleach diluted up to a 9:1 ratio (10%) and lists diluted bleach with a soft brush for surface mildew. Naugahyde's care sheet uses 10% household bleach in 90% water for the most difficult stains. The boating groups disagree. Discover Boating calls bleach "a big no-no" on boat seats: it says caustic cleaners strip the vinyl's remaining anti-microbial, anti-fungal and anti-stain properties, make it brittle and damage the stitching. BoatUS Magazine says products containing bleach break down vinyl and stitching over time. And the EPA, writing about mold in homes, says bleach isn't recommended as a routine part of mold cleanup, and that killing mold isn't enough: dead mold may still cause allergic reactions in some people, so it has to be removed.

If you can't confirm how your seat's vinyl is rated, the cautious order is: soap and water first, then your craft maker's seat cleaner or a marine-vinyl cleaner, and diluted bleach only if the seat's maker approves it, after a spot test, rinsed off thoroughly.

What the sources in this guide say about common seat cleaners. Where your owner's manual differs, follow the manual.
Cleaner or toolWhat the sources saySource
Mild soap and warm waterThe starting point for routine cleaning and most stains, applied with a soft cloth and rinsed with clear water.Morbern, Naugahyde, Discover Boating
Liquid dish soapYamaha's 2021 Maintenance Matters guide: don't use it to wash the craft, because it can strip off important protectants.Yamaha
Your craft maker's seat cleanerSea-Doo's 2026 operator's guide names its XPS All Purpose Cleaner and Degreaser for seat stains; a 2020 Sea-Doo cleaning page says it treats mold and mildew.Sea-Doo
Dedicated marine-vinyl cleanerUse one when mold won't gently scrub away. Morbern publishes a list of cleaners it has tested on its marine vinyls.Discover Boating, Morbern
Diluted household bleachMorbern allows up to 10% on vinyl it specifies as bleach-cleanable, and Naugahyde uses 10% for the most difficult stains, rinsed off; the boating groups say to avoid it on boat seats.CFFA, Morbern, Naugahyde; Discover Boating, BoatUS Magazine
OxiClean powder or a generic equivalentBoatUS Magazine names OxiClean or a generic equivalent: mix as directed, scrub gently with a nylon brush, wait 5 to 10 minutes, then rinse.BoatUS Magazine
Magic EraserBoatUS Magazine suggests trying a Mr. Clean Magic Eraser on tough spots. Test it on a hidden spot first.BoatUS Magazine
Strong detergents, ammonia, acetone, alcohol, solvents, mineral spirits, paint thinners, petroleum productsSea-Doo's operator's guide says never to clean with these. Morbern allows rubbing alcohol or mineral spirits only cautiously, as a last resort on very stubborn stains.Sea-Doo, Morbern
Abrasives, steel wool, citrus cleanersNot recommended on Morbern vinyl.Morbern
Pressure washerSea-Doo warns against one on the bilge and says to use low pressure, such as a garden hose; Yamaha's 2026 VX manual warns against high-pressure water on the engine and engine compartment.Sea-Doo, Yamaha
VinegarNone of the sources in this guide recommends it for seat mold.Not covered

Should you use a vinyl protectant afterward?

The makes disagree here too, and on a jet ski the reason matters. Sea-Doo's 2024 and 2026 operator's guides warn never to apply plastic or vinyl protector to the seat or carpets, because the surface becomes slippery and riders may slip off the watercraft. Yamaha takes the other view: its 2021 Maintenance Matters guide recommends a vinyl dressing after each use to help prevent cracking, and its 2026 VX owner's manual says to wipe vinyl parts such as the seats with a vinyl protectant. Yamaha's own 2022 article on getting a PWC ready for the season goes the other way: it says to avoid common vinyl protectant products, which can make the vinyl slippery. Discover Boating, writing about boat seats in general, also recommends a protectant after using any vinyl cleaner, once the seat is completely dry.

Follow your own manual. If it calls for a protectant, apply it only to a clean, dry seat, as the product label directs, and keep Sea-Doo's slip warning in mind.

When mold stains won't come out

Some stains won't wash out. The CFFA fact sheet describes soil organisms growing in a seat's foam that produce a pink dye. The dye dissolves in the vinyl's plasticizer and migrates to the surface, and the fact sheet says that stain cannot be removed by washing. Discover Boating says much the same of mold that has grown into the cushion: it becomes practically impossible to get rid of.

Don't keep scrubbing harder or reaching for stronger chemicals: Morbern warns that some household cleaners and solvents remove plasticizers from vinyl and make it brittle. The EPA's general advice is that absorbent or porous materials may have to be thrown away if they become moldy, because mold can grow in their empty spaces and crevices. If stains keep returning after a proper clean, ask your dealer or a marine upholstery shop about replacing the seat cover or foam.

How to keep mold off a jet ski seat

Prevention follows from the four things mold needs. The CFFA fact sheet's own list is to keep seats clean, remove any surface growth, use materials treated to resist it, and keep seats covered, if possible, when not in use. Clean and dry are the parts an owner controls every day.

Keeping a jet ski seat mold-free

Where a cover fits in

For a craft stored outside, Sea-Doo's 2024 and 2026 operator's guides say to cover it with an opaque tarpaulin, in part to keep grime and dust off. A cover doesn't dry a seat that is already wet, though, and Kawasaki's 2022 STX 160 manual notes that water can still collect in the footwells of a covered craft left outside. So the order matters: clean, dry, then cover. Sea-Doo's winterizing guide lists the steps in that order: wash, dry thoroughly, then a breathable, fitted cover in a dry, ventilated place. Public Storage's boat-storage advice is the same: allow the boat to dry fully before covering it. Sea-Doo warns that wrapping a craft in plastic or other non-breathable material can cause mold, and its operator's guides say never to store the watercraft in a plastic bag.

Our covers

For outdoor or trailered storage, the Weatherproof Shield has built-in buckles and straps, an elastic hem cord and air vents to aid trailering. For a garage, the Satin Shield is an indoor stretch cover with a fleece interior. Covers are sized by your craft's overall length; see all jet ski covers. If water pools on the cover or moisture builds up under it, see water pooling and moisture under your cover.

Jet ski on its trailer under an open-sided carport, covered by a red and black Weatherproof Shield cover

Trailerable Cover

AllGuard Weatherproof Shield Jet Ski Cover (Trailerable)

For outdoor or trailered storage: built-in buckles and straps, an elastic hem cord and air vents to aid trailering. Seven sizes by overall length.

4 colors: Blue / Black, Gray / Black, Red / Black, Yellow / Black

  • Under 90 inP0
  • Under 102 inP1
  • Under 115 inP2
  • Under 125 inP3
  • Under 135 inP4
  • Under 145 inP5
  • Up to 160 inP6

Lifetime Warranty

Indoor Cover

AllGuard Satin Shield Indoor Jet Ski Cover

For indoor garage storage: a stretch cover with a fleece interior and elastic front and rear hems, for craft up to 138 inches overall.

Color: Black

  • Under 117 inPWC2
  • Up to 138 inPWC3

Lifetime Warranty

The seat steps above fit into a full off-season lay-up: see how to winterize a jet ski, and for where to keep the craft, jet ski winter storage and storing a jet ski in a garage.

Common Questions

Rinse it with fresh water at low pressure, wash it with mild soap and warm water using a soft cloth or soft-bristle brush, and treat any mold that remains with a vinyl-safe cleaner such as your craft maker's seat cleaner. Then rinse repeatedly and let the seat dry completely. Yamaha's 2021 Maintenance Matters guide suggests standing a removed seat on end so the foam drains.

Find your cover size

Covers are sized by your craft's overall length. Measure bow to stern, then match it in the size guide.

Open the size guide

Sources

  1. Doo It Right: Clean and Protect (opens in a new tab)Sea-Doo (BRP) · 2020-05-22
  2. 2026 GTI, GTR and WAKE Series Operator's Guide (Watercraft Care; Storage) (opens in a new tab)BRP · 2026
  3. Spark Series 2024 Operator's Guide (Watercraft Care) (opens in a new tab)BRP · 2024
  4. How to Winterize Your PWC (Personal Watercraft) (opens in a new tab)Sea-Doo (BRP) · 2026-06-09
  5. How Do You Store a Boat for Winter and Every Season? (opens in a new tab)Public Storage · 2026-09-04
  6. Maintenance Matters: A Simple Guide for the Longevity of Your WaveRunner (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2021
  7. Getting Your PWC Ready for the Season (opens in a new tab)Yamaha WaveRunners (Yamaha Motor Corporation, U.S.A.) · 2022-03-16
  8. JET SKI STX 160 Owner's Manual, JT1500R/S/T (2022): End of the Day Checklist, Storage (opens in a new tab)Kawasaki Motors Corp., U.S.A. · viewed online 2026-10-27
  9. Mold and Mildew: An Overview / Marine Upholstery (CFFA fact sheet) (opens in a new tab)Chemical Fabrics & Film Association (hosted by Morbern) · undated; PDF created 2002-05-20; accessed 2026-10-27
  10. Care and Cleaning of Morbern Vinyl Coated Fabrics (opens in a new tab)Morbern · 2017
  11. Approved Cleaners (marine) (opens in a new tab)Morbern · 2025-03
  12. Care and Cleaning Instructions: Naugahyde Vinyl Coated Fabrics (opens in a new tab)Uniroyal Engineered Products (Naugahyde) · 2018-02 (PDF date); accessed 2026-10-27
  13. Cleaning Boat Seats: How to Clean Boat Seats Step-by-Step (opens in a new tab)Discover Boating (NMMA) · accessed 2026-10-27
  14. Boat Cleaning Tips (opens in a new tab)BoatUS Magazine (Stacey Nedrow-Wigmore) · 2018-10
  15. A Brief Guide to Mold, Moisture and Your Home (opens in a new tab)US Environmental Protection Agency · updated 2026-02-18
  16. 8 Tips to Clean Mold (opens in a new tab)Centers for Disease Control and Prevention · reviewed 2024-03-29; read from the web.archive.org copy of 2026-10-02 (the live page returned HTTP 403)
  17. 2026 WaveRunner VX-C/VX/VX Deluxe/VX Cruiser/VX Limited Owner's/Operator's Manual, U.S.A. Edition (LIT-18626-15-77): Cleaning the watercraft (p. 101) (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2026 model year; captured 2026-10-27, page image viewed 2026-10-29

Find Your Size

Measure your jet ski bow to stern in a straight line, then enter the length in inches.

  1. Under 90 inP0
  2. Under 102 inP1
  3. Under 115 inP2
  4. Under 125 inP3
  5. Under 135 inP4
  6. Under 145 inP5
  7. Up to 160 inP6
Full Size Guide

In inches. Decimals are fine.

Covers for Your Jet Ski

All Covers