Trailering

Jet Ski Trailer Maintenance: Bearings, Lights, Tires

What to check before each trip, after salt water and once a year, from the trailer and axle makers' own manuals. Where their intervals differ, each maker is named.

By Alex Quinn 25 min read

Jet ski on a galvanized trailer in a driveway under a loose red and black AllGuard Weatherproof Shield cover, a grease gun and rag by the wheel

Jet ski trailer maintenance comes down to six jobs: keeping the wheel bearings greased and sound, keeping the lights working, keeping the tires and spare road-ready, checking the winch strap and bunks, rinsing the trailer after salt water, and servicing the brakes if it has them. This guide takes them in that order, using what the trailer makers say in their own manuals and maintenance pages (EZ Loader, Karavan, Load Rite and Venture), what Dexter says about its own axles, and the guidance of the BoatUS Foundation, BoatUS Magazine and Discover Boating. Most of these sources write about boat trailers in general, not jet ski trailers in particular. Their intervals don't always agree, so each one is named, with the document's date where it has one.

Hitching, loading and the checks at each fuel stop are in how to trailer a jet ski, and choosing a trailer is in the jet ski trailer buying guide.

Note

Know which hubs your trailer has

Hubs aren't all serviced the same way. The makers cited here describe greased hubs with spring-loaded bearing protectors, systems that grease through the axle spindle (Karavan's Sure Lube, Dexter's E-Z Lube), oil-bath hubs (EZ Loader) and sealed bearings: Sea-Doo describes the wheel bearings on its MOVE trailers as sealed and maintenance-free, and Karavan says some of its models have bearings that need no maintenance and whose metal cap must not be removed. Your trailer's own manual has the final word.

Jet ski trailer maintenance schedule

Load Rite's FAQ sorts boat trailer upkeep into three tiers: checks before each use, grease after a warm hub has been under water (or monthly), and a fuller service once a year. The other makers follow a similar pattern but differ in the details.

Each maker's own guidance, condensed; all read 2026-10-27. EZ Loader: boat trailer owner's manual (2006, revised 2012). Karavan: marine owner's manual (PDF dated 2023). Load Rite: FAQ page (no date shown; page metadata says published 2015, modified 2016). Venture: 'Routine Boat Trailer Maintenance' (June 2026), drawn from its owner's manual. Dexter: Trailer & RV Maintenance Schedule (April 2026), for Dexter axles. Winch strap and bunk checks are in their own section below. Follow the manual for your own trailer.
TaskEZ Loader (2006 manual, rev. 2012)Karavan (2023 manual)Load Rite (FAQ)Venture (2026 article)Dexter axles (2026 schedule)
Grease the hubsBefore launching or storage, with a hand-operated grease gun; not when the hub is coldCheck just before launching that the hub is full of greaseAfter each time a warm hub goes under water, or monthly, whichever comes firstEvery 3 months or 1,000 miles, whichever comes first (its summary list says monthly)Not a separate line; see the 12-month repack
Inspect and repack the bearingsInspect the bearings and replace the seals when the season ends or before storageRepack before storage; at least twice in a season if the trailer goes in the water oftenOnce a year: take apart, clean, inspect and repack every wheel bearingOnce a year, whatever the mileage: pull the hub and inspect the bearings and racesEvery 12 months or 12,000 miles: inspect for corrosion or wear; clean and repack
SealsReplace at season's end or before storageFit a new rear seal when the rear bearing comes outReplace the inner seal every time the hub comes offReplace the inner hub seal and cotter pin at every reassemblyEvery 12 months or 12,000 miles: inspect for leakage; replace if removed
Tire pressureBefore each trip, cold, to the pressure on the VIN decalEach time before towing, coldInflate cold to the full rated pressure on the sidewallAt least monthly and before every trip, to the maximum cold pressure on the sidewallEvery use: inflate to the manufacturer's specs
Lug nutsBefore every trip; per its tightening method, re-torque after 50 miles of use, then periodicallyBefore each tow, all bolts and nuts tightBefore each use, and at each fuel stop on longer tripsAfter fitting a wheel: re-torque at 10, 25 and 50 miles, then periodicallyEvery 3 months or 3,000 miles, to the specified torque
Lights and wiringLights before any trip; trace the wiring twice a yearLights working before each tow; coat the metal under the lenses once a yearLights and wiring before each useLights before every trip; plugs and harness once a yearTrailer brake wiring every 12 months or 12,000 miles
Brakes, if fittedTest before each trip; drum brakes inspected and adjusted each season start or every 2,000 miles, whichever comes firstCheck brake operation before each towAdjust drum brakes regularly; bleed the fluid once a yearInspect pads, rotors and calipers once a yearTest every use; adjust every 3 months or 3,000 miles (not needed with Nev-R-Adjust)

Two things line up across the table. Every maker in it calls for a closer look at the bearings at least once a year or at the end of the season. And Karavan, Load Rite and EZ Loader each tie greasing or checks to the hubs going under water.

Wheel bearings and hubs

EZ Loader's 2006 manual says that because its trailers are put in water and other severe conditions, the wheels and their parts need more attention than a car's. Load Rite explains the risk: a hub that's warm from the road and goes straight into the water at launch cools quickly, the grease contracts, and water is drawn in. Karavan warns that warm hubs backed in just after a long tow take on water through condensation, and says to let them cool first. For hubs without bearing protectors, the BoatUS Foundation says it's best to keep them out of the water, and if you must dunk them, to let them cool first or cold water will be drawn inside, displacing the grease and causing the bearings to corrode and fail. Venture's advice if you do launch with hot hubs is to grease them right after, so fresh grease pushes out any water.

To check for play in the bearings, Karavan suggests rocking each wheel once or twice a year, depending on use. EZ Loader's version of the check:

Check a trailer wheel bearing in five steps

  1. Step 1: Secure the trailer

    EZ Loader says to make sure the trailer can't move: attach it to the tow vehicle and block the tires.

  2. Step 2: Raise the wheel

    Jack the wheel clear of the ground. For its own trailers, EZ Loader puts the jack under the axle where the spring mounts on tubular steel trailers; on a torsion axle, under the axle tube as near the tire as possible but not on the torsion arm (or under the main frame rail as close to the axle as possible if it won't fit); and on aluminum I-beam trailers, only under the axle.

  3. Step 3: Rock the wheel

    With your hands on the outside edges of the tire, push on one side and pull on the other. EZ Loader says there should be no noticeable rocking; Karavan says play means the castle nut needs adjusting, per its bearing-adjustment steps.

  4. Step 4: Spin it and listen

    EZ Loader says smooth, silent turning means the bearings are in good order, and a grinding sound means it's time to contact the dealer.

  5. Step 5: Look at the cap, the seal and the fender

    EZ Loader says a film of grease around the seal is normal, but a seal that leaks a lot should be replaced by a dealer. Discover Boating says grease on the inside of a fender means a bad bearing seal to replace before going on the road, and asks whether the dust caps are secure.

Bearing protectors and dust caps

The BoatUS Foundation describes bearing protectors as metal caps with springs that hold grease under pressure, says they keep water out of the hub, and says a trailer without them should have them added. BoatUS Magazine's April 2015 repacking guide tells them apart from a plain dust cap: a dust cap has a small lip you can pry under, a protector has none. If you're adding protectors, it suggests bringing the old dust cap to the parts store, since they come in a few sizes; EZ Loader also says to match the protector to the hub. Adding grease through one:

  • Check the level. EZ Loader says to rock the disc on the protector's face with your fingers: if it moves, it's floating on grease and needs none; if it has bottomed out, add grease. The BoatUS Foundation presses the protector at the edge: if it moves it doesn't need grease, if it's rigid it does. On clear caps with a sight disc, Load Rite says to add grease whenever the disc drops below the marked minimum line.
  • Add it by hand, and stop early. EZ Loader says to use a hand-operated grease gun, never a power-assisted one, to stop when the spring begins to compress, and not to add grease when the hub is cold. BoatUS Magazine (2015) warns that over-greasing pushes grease past the seal lip and leads to seal failure.
  • Use the right grease. Load Rite, Venture and Dexter (for its E-Z Lube axles) each name a lithium complex NLGI #2 grease, and Load Rite says the type matters more than the brand. Karavan says not to mix greases with different thickeners.

Spindle systems work differently. On Karavan's Sure Lube, the grease fitting sits under a rubber dust cap, and you add grease until it shows by the castle nut; Karavan says small silver filings in the old grease can mean a bad bearing, to be replaced immediately. Dexter says its E-Z Lube is designed to allow immersion in water, and that E-Z Lube axles still follow the inspection procedures in its service manual.

Topping up isn't the whole job. EZ Loader says bearing protectors are not a replacement for proper bearing maintenance, and Load Rite says the only way to get rid of contaminated grease is to pull the hub, clean and inspect it, and repack the bearings.

Gloved hand pressing a grease gun hose onto the fitting at the center of a chrome bearing protector on a galvanized trailer wheel

How often to repack the bearings

A repack, as BoatUS Magazine's April 2015 guide walks through it, means pulling the hub, cleaning out the old grease, inspecting the bearings and races, packing fresh grease and fitting a new seal. Load Rite calls for it once a year, and Venture calls for a full hub disassembly and bearing service once a year, regardless of mileage; Dexter lists clean and repack every 12 months or 12,000 miles for its axles; and BoatUS Magazine (2015) says the grease should be changed at least once per season, and more often if you trailer long distances or often. Karavan's 2023 manual says no single mileage fits every owner: it says to check the grease once a year, repack before storage or whenever the grease looks contaminated, and repack at least twice in a season if the trailer goes in the water often (its towing checklist says at least twice a year and before storing).

Once the hub is apart, Load Rite says rust, bluing or pitting on a bearing cone or race means immediate replacement, and BoatUS Magazine (2015) says never to replace bearings without their races, because they're matched. The BoatUS Foundation adds that with most hubs the seals must be replaced whenever they're removed for packing, and that even with protectors it's a good idea to carry spare bearings on a long trip.

Trailer lights and wiring

EZ Loader, Karavan, Load Rite and Venture all check the lights before each trip or each use; Discover Boating has someone stand behind the trailer while you work the lights and turn signals. The deeper checks are about corrosion and the connector:

  • Trace the wiring. EZ Loader says to trace it twice a year, from the tow vehicle to the taillights, for bare wires, cracked insulation and corroded terminals. The BoatUS Foundation also says twice a year, and says exposed wire should be secured every 18 inches to prevent chafing.
  • Protect the contacts. EZ Loader puts grease or petroleum jelly on plug contacts and bulb bases. Venture unplugs each light once a year, sands any oxidation off the plugs with emery cloth and dips them in dielectric grease. Karavan takes the lenses off once a year and coats the metal parts, for example with petroleum jelly.
  • Check the ground. EZ Loader says the white ground wire must be connected to the trailer frame; Karavan says to secure it to both the trailer and the tow vehicle, and that a poor ground makes the taillights blink.
  • Keep the plug out of the water. EZ Loader says to disconnect the light harness before submerging the trailer, even with submersible lights, and notes that unplugging also disables electric brakes. The BoatUS Foundation says not to let the connector plug get dunked, even with sealed lights. Karavan says a bulb lit under water burns out, so disconnect before backing in unless the tail lights are built for immersion.
  • Carry spares; don't bag the lights. The BoatUS Foundation suggests carrying spare bulbs and fuses. For storage, EZ Loader says not to put plastic bags around the light fixtures, because condensation will cause corrosion.

EZ Loader says LED lights require no maintenance; Venture says a failed LED unit gets replaced, not repaired, but the harness and grounds still need checking. Both EZ Loader and Karavan print the same four-wire color code:

The four-wire color code as each manual prints it, read 2026-10-27. EZ Loader also lists a blue wire for underwater lights on custom trailers. Check the wiring diagram for your own trailer.
Wire colorEZ Loader (2006 manual)Karavan (2023 manual)
WhiteGroundGround
BrownTail lights, rear marker light, front and rear side lightsTaillights, rear marker lights, front and rear side lights
YellowLeft stop and turnLeft stop and turn
GreenRight stop and turnRight stop and turn
Hands dabbing grease onto the pins of a trailer tail light's wiring plug, beside an open tub of grease on a galvanized trailer frame

Tires, lug nuts and the spare

Pressure. There's no single jet ski trailer tire pressure: the number comes from your trailer and your tire. Load Rite says trailer tires designated ST are designed to be inflated cold to the full rated pressure on the tire sidewall, and Venture says trailer tires should be inflated to the maximum cold pressure listed on the sidewall. EZ Loader's 2006 manual points to the recommended pressure on the VIN decal at the left front of its trailers. BoatUS Magazine (2012) notes that boat trailer tires typically need higher pressure than tow-vehicle tires. Measure cold: EZ Loader means before driving, or after the trailer has stood at least 3 hours, because even short distances warm the tires. Check the spare too (EZ Loader, BoatUS Magazine).

Wear and age. The BoatUS Foundation says trailer tires sometimes need replacing long before the tread wears out, and that spider-web cracks on the sidewall mean the tire is rotten. EZ Loader links small sidewall cracks to age or to sitting in intense sunlight. BoatUS Magazine (2013) dates a tire by the last four digits of the DOT code on the sidewall: week, then year, so 1209 is the 12th week of 2009 (on some brands it's on the inside sidewall). None of the sources read for this guide gives a set number of years after which to replace a trailer tire; the condition checks they do give are below.

Tire checks before each trip (EZ Loader)

EZ Loader says that if any of these turn up, don't use the trailer until the problem is fixed. BoatUS Magazine reads the wear: center wear means too much pressure, wear on the outside edges too little; Venture adds that wear on one edge only suggests misalignment or a bent axle. For a trailer that sits, the BoatUS Foundation says tires deteriorate in sunlight and suggests storing them indoors during long idle spells, and BoatUS Magazine (2012) suggests tire covers and parking on concrete or plywood rather than grass.

Replacing a tire. EZ Loader says to use only the size and type on the trailer's VIN label, and that the load capacities of all the tires together should meet or exceed the trailer's GVWR. Load Rite says never to use a tire without the ST designation on its trailers, and the BoatUS Foundation says never to mix bias-ply and radial tires. The sidewall gives the size: in EZ Loader's example, ST205/75R14C is a special trailer tire 205 mm wide, with a 75 percent aspect ratio, radial, for a 14-inch wheel, load range C.

Lug nuts and the spare. Load Rite tightens lug nuts in a crisscross star pattern. Torque values differ by maker and wheel (Karavan's manual lists them by wheel size and material), so use the figure for your trailer. The BoatUS Foundation urges carrying a spare and says a U-bolt can attach it directly to the frame; it warns that a typical car jack won't work on a trailer, so carry a scissors jack large enough for the load. EZ Loader suggests a small hydraulic jack, and Yamaha's 2021 Maintenance Matters guide says to keep the spare aired up and checked regularly.

Winch strap and bunks

The winch strap. EZ Loader's 2006 manual says to check the winch line, strap or cable for fraying, cuts or tears, to replace it immediately if it's damaged, and to keep it from rubbing against anything sharp. The BoatUS Foundation says to check it frequently, because even a slight amount of wear can significantly reduce the strap's weight-carrying ability. Venture inspects the strap before every trip for fraying, cuts or worn stitching and replaces it at the first sign of damage. For the winch itself, EZ Loader says to keep it clean and lubricated with heavy grease on the gears, Venture greases the gears every six months, and the BoatUS Foundation checks for loose mounting bolts. The BoatUS Foundation also says winches are made for loading and unloading, not for holding the craft on the trailer on the road; road straps are covered in how to tie down a jet ski on a trailer.

The bunks. Yamaha's 2021 guide says to tighten anything loose, replace anything sagging or rotted, and keep the bunks in proper contact with the hull to prevent hooks or rockers forming in it; its checklist includes inspecting the bunks for damaged boards or torn carpet. Discover Boating looks for excessive wear on the bunk carpeting, which is easier with the craft off the trailer. Venture's routine: check the carpet for trapped sand or gravel before loading (it calls grit between carpet and hull the leading cause of hull scratches); once a year, inspect the carpet for tears or exposed wood and replace it with marine-grade carpet only, since it says indoor-outdoor carpet holds water and speeds up wood rot; and once a year, replace cracked or rotted boards. If the bunks have plastic covers instead of carpet, EZ Loader warns they're very slippery, so the craft may start to slide as soon as the winch strap tension is released. Setting the bunks to the hull is covered in how to trailer a jet ski.

Gloved hand brushing sand off the gray carpet of a trailer bunk, with a galvanized bunk bracket bolted below

Rinsing the trailer after salt water

The sources here that cover rinsing all call for a rinse after salt water (EZ Loader, Venture and Yamaha specify fresh water), and the BoatUS Foundation and Venture say a galvanized frame still needs it (Venture adds aluminum). The BoatUS Foundation says that to prevent rust, even a trailer with a galvanized frame should be rinsed thoroughly when it has been dunked in saltwater. Venture rinses the entire frame with fresh water after every launch and says neither galvanized steel nor aluminum is maintenance-free: aluminum won't rust, but it oxidizes into a white, chalky buildup, and Venture says never to use ammonia or trisodium phosphate on it. EZ Loader's 2006 manual calls washing with soap and rinsing with fresh water after every use one of the best maintenance procedures for its trailers. Frame choices are compared in the jet ski trailer buying guide.

After a saltwater launch

Trailer brakes, if fitted

Whether a trailer must have brakes is set state by state. Load Rite says brake laws vary by state and to check with the DMV where the trailer will be registered (it recommends brakes on all axles where available), and Karavan's manual says trailer laws covering brakes vary from state to state. If your trailer has brakes:

  • Keep them dry. EZ Loader says brakes last longer if they don't get wet, and that after they've been submerged you should run the trailer for ten minutes before applying them. The BoatUS Foundation says surge brakes are frequently wrecked by dunking, and that newer models have flushing devices that offer some protection.
  • Test them. EZ Loader tests the brakes before each trip and after the wheel bearings have been lubricated, and warns that grease or oil on the brakes can stop them working correctly. For its axles, Dexter also checks the breakaway system's battery charge and switch at every use.
  • Adjust drums. EZ Loader says drum-style brakes are not self-adjusting, and Load Rite says the drum brakes used on its trailers don't self-adjust. EZ Loader adjusts them after the first 1,000 miles, then at the start of each season or every 2,000 miles, whichever comes first, inspecting the wheel bearings and seals at the same time. EZ Loader says its own disc brakes need no adjustment, and Load Rite says disc brakes require none.
  • Pads and fluid. Load Rite says the serviceable limit for brake shoes or pads is commonly considered 3/32 inch from the top of the rivet to the pad surface, and Venture says pads should be replaced when the friction material reaches 3/32 inch or less. Load Rite bleeds the fluid once a year with fresh DOT 3 from an unopened container; Venture renews it after the first year, then every one to two years.
  • End of season. EZ Loader says trailer brake makers recommend removing the drums for inspection when the season is over, and that drum-brake trailers should get a rust inhibitor at least once a year.

EZ Loader adds that only a qualified mechanic trained in braking systems should attempt brake adjustment, repair and replacement.

The axle and suspension

Load Rite and EZ Loader both list torsion axle suspension on their PWC trailer pages. Venture calls torsion axles essentially maintenance-free, with no serviceable internal parts; what needs watching is the outside. If the torsion arms look bent, sagging or uneven, Venture says the axle needs replacing, and a trailer that gradually sits lower or unevenly is a sign the arms are losing elasticity.

Leaf springs need more. Venture inspects the hangers, shackles and equalizer hardware every six months for cracks or excessive rust, checks the axle alignment every 12 months, and coats the spring assembly with grease once a year. For trailers on Dexter axles, Dexter's schedule greases the suspension's wet bolts and equalizers every 3 months or 3,000 miles, inspects the suspension parts every 6 months or 6,000 miles, and checks the springs for loss of arch and the hanger welds every 12 months or 12,000 miles. Load Rite's annual list adds a visual inspection of the frame and axles for rust, damage and fractures, and a check of every fastener.

Jet ski trailer accessories and parts

Trailer makers' parts stores and option lists name the parts that most of the jobs above involve. The table lists the categories as the makers name them on their own pages; it's a guide to what to ask for, not a recommendation of any brand or product. When ordering parts, Load Rite asks for the trailer's model and VIN, because parts can vary by model year even when model numbers match.

Category names as published on each maker's page, read 2026-10-27. Listed to show what each part is called, not as endorsements. Match any part to your trailer's model and VIN.
CategoryWhat it's for, per the sourcesWhere the makers name it
Dust caps, grease caps and bearing protectorsCaps on the end of the hub; a bearing protector holds grease under spring pressure (BoatUS Foundation). Match the size to the hub (EZ Loader)Load Rite store: 'Spindles, Grease Caps & Spindle Components'
Bearings, seals and racesReplaced as needed at a repackLoad Rite store: 'Bearings, Seals & Races'
Bunk brackets, boards and carpetHold and cover the long supports the hull rests on (EZ Loader: usually wood or aluminum, carpeted or plastic-covered)Load Rite store: 'Bunk Brackets', 'Bunk Boards', 'Bunk Carpet & Plastic Bunk Covers'. Yacht Club option: poly bunk wrap
GuidesAttach to the sides of the trailer to help keep the hull centered when loading or launching (EZ Loader)Load Rite store: 'Side Guides'. Yacht Club option: PVC load guides
Lights and wiringTail and marker lights, the harness and its connectorsLoad Rite store: 'Taillight Assemblies', 'Marker Lights & Clearance Lights', 'Wire Harness & Light Hardware/Connectors'
Spare tire and carrierA U-bolt can attach the spare to the frame (BoatUS Foundation)Load Rite store: 'Spare Tire Carriers'. Yacht Club options: U-bolt and side-mount carriers, spare tire
Winch partsStraps, cables, handles and bow stopsLoad Rite store: 'Winches, Cables, Winch Straps, Winch Handles', 'Bow Stops, End Caps, End Bells'
Axles and hubsComplete spring or torsion axles, hubs and drumsLoad Rite store: 'Axle Assemblies & Weldments - Spring & Torsion', 'Hubs, Rotors, Drums'

A cover for the craft on the trailer

Yamaha's 2021 Maintenance Matters guide says to protect a WaveRunner with a Yamaha storage cover when it's not in use or when trailering. Our Weatherproof Shield is sold as a trailerable jet ski cover, with air vents to aid trailering, built-in buckles and straps and an elastic hem cord. It's made of 600D solution-dyed polyester with a PU coating, it's water-resistant, and it comes with a mesh storage bag, an extra strap set and a Lifetime warranty (warranty details). Its buckles and straps hold the cover; they aren't tie-downs for the craft. The Satin Shield is an indoor cover (Satin storage bag included), not a trailering cover.

Size the cover by your craft's overall length with the jet ski cover size guide, or browse all jet ski covers. Before towing with it on, read can you trailer a jet ski with the cover on, and for where to keep the craft between trips, see jet ski storage.

Trailerable Cover

AllGuard Weatherproof Shield Jet Ski Cover (Trailerable)

Sold as trailerable: air vents to aid trailering, built-in buckles and straps, an elastic hem cord and an extra strap set. Water-resistant 600D polyester with PU coating.

4 colors: Blue / Black, Gray / Black, Red / Black, Yellow / Black

  • Under 90 inP0
  • Under 102 inP1
  • Under 115 inP2
  • Under 125 inP3
  • Under 135 inP4
  • Under 145 inP5
  • Up to 160 inP6

Lifetime Warranty

Find the cover size for your craft

Covers go by overall length. Match your jet ski's length in the size guide.

Open the size guide

Jet ski trailer maintenance FAQ

It depends on the hub and the maker. Load Rite says to add grease each time a warm hub has been under water, or monthly, whichever comes first; Venture's 2026 article says every 3 months or 1,000 miles; EZ Loader's manual (2006, revised 2012) says before launching or storage, never when the hub is cold. Sea-Doo describes the sealed bearings on its MOVE trailers as maintenance-free. Follow your trailer's manual.

Sources

  1. Boat Trailer Owner's Manual: Trailer Lights (p. 12), Winch (pp. 12-13), Trailer Maintenance and Storage (p. 20), Brake Operation and Maintenance (pp. 21-24), Jack Placement (p. 24), Wheel, Tire and Hub Care (pp. 25-27), Tire Information (pp. 28-31) (opens in a new tab)EZ Loader Adjustable Boat Trailers · 2006 document (PDF created 2006-06-06, modified 2012-03-21), linked from ezloader.com; read 2026-10-27
  2. Owner's Manual: Marine (Karavan watercraft trailers): Hubs, Bearings, Races and Seals; Sure Lube; Bearing Repacking; Lighting and Wiring; Towing Your Trailer (opens in a new tab)Karavan Trailers · PDF created 2023-09-29 (no print date on the pages), linked from karavantrailers.com; read 2026-10-27
  3. FAQs: Bearings, Brakes, Tires, Lug Nuts, Maintenance, Parts (opens in a new tab)Load Rite Trailers · no date shown on the page; page metadata: published 2015-11-02, modified 2016-07-08; read 2026-10-27
  4. Routine Boat Trailer Maintenance: What Every Owner Should Know (drawn from the Venture Boat Trailer Owner's Manual) (opens in a new tab)Venture Trailers · published 2026-06-27, updated 2026-07-08; read 2026-10-27
  5. The Ultimate Trailer & RV Maintenance Schedule (LIT-516-01) (opens in a new tab)Dexter Axle Company · 2026.04 edition; read 2026-10-27
  6. E-Z Lube bearing lubrication (LIT-239-00) (opens in a new tab)Dexter Axle Company · 2019.05 edition; read 2026-10-27
  7. Transportation & Trailering (Boating Safety Study Guide), Part II: Trailer Maintenance (opens in a new tab)BoatUS Foundation · page undated; read 2026-10-27
  8. How To Change And Repack Wheel Bearings (John Tiger, BoatUS Magazine) (opens in a new tab)BoatUS · published April 2015; read 2026-10-27
  9. 11 Things To Know About Boat Trailer Tires (Pat Piper, BoatUS Magazine) (opens in a new tab)BoatUS · published June 2012; read 2026-10-27
  10. The Lowdown On Tires (Pat Piper, BoatUS Magazine) (opens in a new tab)BoatUS · published June 2013; read 2026-10-27
  11. Your Ultimate Trailering Checklist (content courtesy of BoatUS) (opens in a new tab)Discover Boating (NMMA) · page undated; read 2026-10-27
  12. Boat Trailer Tips (Steve Tadd and Nicolette Belczak) (opens in a new tab)Discover Boating (NMMA) · page undated; read 2026-10-27
  13. Maintenance Matters: A Simple Guide for the Longevity of Your WaveRunner (pre-ride checklist; trailer tips) (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2021; read 2026-10-27
  14. MOVE Trailers (sealed maintenance-free wheel bearings, carpeted bunks) (opens in a new tab)BRP (Sea-Doo) · 2026-10-27
  15. PWC Trailer Models (steel): adjustable bunks, sealed hubs (opens in a new tab)EZ Loader · 2026-10-27
  16. Single Watercraft Steel Trailer: Sure-Lube Wheel Bearing Grease System, ShortFree Lighting System (opens in a new tab)Karavan Trailers · 2026-10-27
  17. Load Rite Galvanized Single PWC: carpeted adjustable bunks, torsion suspension, LED lighting, greaseable hubs (opens in a new tab)Load Rite Trailers · 2026-10-27
  18. Trailer parts store: category list (Spindles, Grease Caps & Spindle Components; Bearings, Seals & Races; Bunk Brackets; Side Guides; Wire Harness & Light Hardware/Connectors; Spare Tire Carriers; Winches, Cables, Winch Straps, Winch Handles) (opens in a new tab)Load Rite Trailers · 2026-10-27
  19. Steel PWC Trailers: standard features and options (grease zerks on all hubs, carpet bunks, LED lights, PVC load guides, poly bunk wrap, spare tire carriers, spare tire) (opens in a new tab)Yacht Club Trailers · 2026-10-27

Find Your Size

Measure your jet ski bow to stern in a straight line, then enter the length in inches.

  1. Under 90 inP0
  2. Under 102 inP1
  3. Under 115 inP2
  4. Under 125 inP3
  5. Under 135 inP4
  6. Under 145 inP5
  7. Up to 160 inP6
Full Size Guide

In inches. Decimals are fine.

Covers for Your Jet Ski

All Covers