Trailering

How to Tie Down a Jet Ski on a Trailer

The Sea-Doo, Yamaha and Kawasaki manuals cited here all point tie-downs at the bow and stern eyes, and BoatUS and EZ Loader both warn against relying on the winch strap alone. Here's the full setup, step by step.

By Alex Quinn 15 min read

To tie down a jet ski on a trailer, secure it at both ends. At the bow, the winch strap pulls the craft snug and a safety chain or second strap backs it up on the bow eye. At the stern, transom straps run from the stern eyes down to the trailer. The winch strap is never the whole job: the BoatUS Foundation says winches are designed for loading and unloading, not to hold a boat on the trailer going down the road, and EZ Loader's 2006 trailer manual says not to depend on the winch line, strap or cable alone.

Several of the sources here describe that two-ended setup. Sea-Doo's 2026 GTI and 2024 Spark operator's guides say to tie the craft to both front and rear (bow/stern) eyelets, and BoatUS, Discover Boating and EZ Loader all describe securing a boat at the bow and at the stern. Below: where Sea-Doo, Yamaha and Kawasaki say to attach straps and where not to, the strap types and who recommends each, the bow and stern setups, a step-by-step routine and a checklist. For the rest of the trip, from hitching up to launching, see our guide to how to trailer a jet ski.

Note

Your owner's manual has the final say

Tie-down points and cautions differ by make and model. The manuals quoted here cover specific models and years: Sea-Doo's 2026 GTI, GTR and Wake and 2024 Spark operator's guides, Yamaha's 2026 VX owner's manual and Kawasaki's 2022 STX 160 owner's manual. The trailer manual quoted is EZ Loader's 2006 owner's manual for its boat trailers. Where this guide and your manual differ, follow your manual, and follow your trailer maker's instructions for its tie-down points.

Where to attach tie-downs on a jet ski

In the manuals cited here, the three craft makers agree on the attachment points: the eyes or eyelets at the bow and the stern. Each also says where tie-downs must not go. Here is what each manual says.

From each maker's operator's or owner's manual, read 2026-10-27. Your model's manual may differ.
MakerManual citedTie down toKeep tie-downs offPadding
Sea-Doo2026 GTI, GTR and Wake guide, pp. 35 and 137; 2024 Spark guide, p. 31Front and rear (bow/stern) eyelets, plus additional tie-downs if necessaryThe seat (don't route straps over it) and the grab handleWrap ropes or tie-downs with rags or similar protectors where they touch the body
Yamaha2026 VX owner's manual, p. 75The bow eye and the stern eyesEvery other part of the craftWrap ropes or tie-downs with towels or rags where they touch the body
Kawasaki2022 STX 160 owner's manual, pp. 119-120The bow and stern eyes onlyThe handrail: tie-downs there can damage the handrail and/or hullNot covered on these pages

The eyes have more than one job, and the manuals say which fittings do which. Describing the front eyelet, Sea-Doo's 2026 guide says eyelets can be used for mooring, towing and as tie-down points when trailering, but warns not to use them to lift the watercraft. Its mooring cleats can be used for docking, and Sea-Doo warns never to use them to pull or lift the craft; the molded grab handle isn't for towing anything or lifting the craft either. Yamaha's 2026 VX manual uses the bow eye for transporting, mooring or towing in an emergency and the stern eyes for transporting or mooring, and warns not to use the cleat to lift the watercraft.

Kawasaki's manual states the goal: fasten the watercraft securely to prevent movement between the craft and the trailer, on a trailer that matches the craft's weight and hull design. For trailer sizes and capacities, see jet ski trailer size and dimensions.

Types of jet ski trailer straps

Jet ski trailer straps come in a handful of types, and each does a different job. Here is what each one is for and which source recommends it.

Compiled from the sources named in each row, read 2026-10-27. BoatUS and Discover Boating write about trailer boats in general; EZ Loader's 2006 manual covers its boat trailers.
Strap or chainWhere it goesWhat it doesWho recommends it
Winch strapFrom the trailer winch to the bow eyePulls the craft onto the trailer and snug against the bow stopSea-Doo and EZ Loader use it for loading; BoatUS says it is not a tie-down
Bow safety chain or second bow strapFrom the bow eye down to the trailerBacks up the winch strap at the bowEZ Loader (bow safety chain), BoatUS (bow chain and hook), BoatUS Foundation (a separate line from the bow eye)
Transom strapsFrom each stern eye down to the trailer's rear tie-down pointsHold the stern down so the craft doesn't bounce on the trailerSea-Doo, Discover Boating, BoatUS, EZ Loader
Gunwale strapAt the stern, which BoatUS says is secured 'by gunwale or transom straps'; it doesn't say how the strap runsAn alternative or addition to transom straps, in BoatUS's advice for boatsBoatUS, for boats in general; see the jet ski caution below
Trailer safety chainsCrossed under the tongue, from the trailer to the tow vehicleHelp keep the tongue off the road if the coupler comes off the ballEZ Loader, BoatUS Foundation, Discover Boating
Tie-down gear on concrete: a blue winch strap, a galvanized chain with a snap hook, ratchet and cam-buckle straps, and two folded towels

Gunwale and over-the-top straps

BoatUS, writing about trailer boats in general, says tie-downs secure a boat at the bow and at either the gunwale or the transom, preferably both. Discover Boating's trailer tips add that a boat's beam may also need additional straps. The jet ski makers are more specific about their craft. Sea-Doo's 2026 GTI and 2024 Spark operator's guides allow additional tie-downs if necessary, but say not to route ropes or tie-downs over the seat or attach them to the grab handle, so those parts aren't permanently damaged. Yamaha's 2026 VX manual says not to attach ropes or tie-downs to any part of the craft other than the bow eye and stern eyes, or the craft may be damaged. Before you run any strap across a jet ski, check what your own manual allows.

Ratchet or cam buckle?

BoatUS says ratchet or cam-style straps of adequate size can secure a boat on its trailer very securely and keep it from bouncing and suffering chafe damage. It adds that the right gunwale or transom strap length depends on the boat's width and transom height. None of the Sea-Doo, Yamaha or Kawasaki manual pages cited here names a buckle type.

The difference is how the strap is tightened. US Cargo Control, a tie-down supplier, explains it in a 2012 blog post about cargo in general: a ratchet strap is tightened by a ratcheting mechanism that gives more leverage, which it suggests for heavy loads, while a cam buckle strap is pulled tight by hand and locked with a thumb release, which it suggests for lighter or more delicate cargo because hand tightening makes over-tightening damage less likely. Whichever you use, BoatUS warns that tie-downs must not cross sharp edges, because any force will cut the strap.

The bow: winch strap and safety chain

The jet ski trailer winch strap does the loading. EZ Loader's 2006 trailer manual, written for boats, says to set the winch height so the strap is level with the bow eye when the boat rests on the trailer, with the bow stop roller or V-block just above the eye. The winch then pulls the bow eye straight into the underside of the bow stop, without lifting or pulling down the bow.

Winching has its own hazards. EZ Loader says to lock the winch before winding the strap in, to keep at least three turns of strap on the drum and never let it all the way out, and, if the handle slips out of your hand, to let it spin rather than try to stop it. The BoatUS Foundation says to keep everyone out of the direct line of the winch cable, because if it breaks the whiplash can seriously injure someone.

Once the craft is snug, back up the winch. EZ Loader says the bow safety chain supplied on most of its models should be attached to the bow eye after the winch firmly pulls the boat against the bow stop. BoatUS says not to rely on winch gears, the winch strap or electric winch brakes, and always to use a bow chain and hook as an added safety measure; the BoatUS Foundation suggests a separate line from the bow eye down to the trailer. Discover Boating's ramp-etiquette advice is not to pull up the ramp before the bow strap and safety chains are secure.

Check the gear itself, too. The BoatUS Foundation says that, in general, a winch should be rated to pull at least half the combined weight of the boat, motor and gear; our guide to how much a jet ski weighs has the craft weights. It also warns that even slight wear on the strap can significantly reduce its weight-carrying ability. EZ Loader says to replace a frayed, cut or torn winch line right away and to keep it from rubbing against anything sharp, and Yamaha's 2021 Maintenance Matters guide says to replace a winch cable at any sign of cuts, abrasion or chafing.

Side view of a jet ski bow on its trailer: a blue winch strap runs level from the winch to the bow eye, with a galvanized chain on the same eye

Transom straps: why the winch strap isn't enough

The winch strap is for loading, and the sources are blunt about it. The BoatUS Foundation says winches are designed for one thing, loading and unloading, and are not designed to hold a boat on the trailer going down the road. BoatUS says winch straps, rope and cable are not tie-down devices at all. EZ Loader says not to depend on the winch line, strap or cable alone to hold the boat secure.

The stern needs its own straps. BoatUS says a heavy strap should always anchor the boat's stern to the trailer; without one, the boat will bounce against or off the trailer. EZ Loader says to tie the stern down securely, in both a downward and a forward direction, with approved tie-downs on the rear tie-down points provided on the trailer. Discover Boating's towing advice is to secure the boat at both the bow eye and with tie-downs at the transom, and Sea-Doo's inspection page says to make sure both the winch strap and the transom straps are secure and tight.

On a jet ski, the transom straps go on the stern eyes: Yamaha's 2026 VX and Kawasaki's 2022 STX 160 manuals name the stern eyes, and Sea-Doo's 2026 GTI and 2024 Spark guides say to tie to both front and rear (bow/stern) eyelets. Pad each strap where it touches the body, as Sea-Doo and Yamaha direct. Then try to rock the craft. EZ Loader says that if the winch line and tie-downs are tight and you can still rock the boat on the trailer, check the bunk or roller settings and the winch adjustment.

Black transom strap hooked into a jet ski's stern eye and run down to the trailer rail, with a ratchet buckle and a towel padding the hull edge

How to strap down a jet ski, step by step

This order follows Sea-Doo's launch-and-load guide and Discover Boating's ramp advice: secure the bow at the ramp, then finish the straps in the parking or staging area, away from the ramp.

Tie down a jet ski after loading

  1. Step 1: Winch the bow snug

    With the craft on the bunks, hook the winch strap to the bow eye and wind it in until the bow eye is snug under the bow stop. Lock the winch before you wind, keep at least three turns of strap on the drum, and keep everyone out of the strap's line (EZ Loader; BoatUS Foundation).

  2. Step 2: Clip on the bow safety chain

    Attach the bow safety chain or a second strap to the bow eye before the tow vehicle pulls up the ramp (EZ Loader; Discover Boating).

  3. Step 3: Pull clear of the ramp

    Drive to the parking or staging area to finish, as Sea-Doo and Discover Boating advise, and unload loose gear there.

  4. Step 4: Strap the stern

    Hook a transom strap to each stern eye and to the trailer's rear tie-down points, pulling down and forward, and check that each buckle is locked (EZ Loader; Discover Boating). Pad the straps where they touch the body, and keep them off the seat, grab handle, handrails and sharp edges (Sea-Doo; Yamaha; Kawasaki; BoatUS).

  5. Step 5: Latch and stow everything

    Make sure the fuel cap, storage compartment covers, boarding platform and seat are latched, and that accessories and cargo are secured or removed (Sea-Doo).

  6. Step 6: Try to rock the craft

    Push on the craft. If the straps are tight and it still rocks on the trailer, EZ Loader says to check the bunk or roller settings and the winch adjustment.

  7. Step 7: Hook up the trailer

    Lock the coupler on the ball and cross the trailer safety chains under the tongue to the tow vehicle (EZ Loader; Discover Boating). EZ Loader's 2006 manual says "most state laws require the crisscrossing of these chains or cables," and Discover Boating suggests stainless snap shackles in place of standard S-hooks.

  8. Step 8: Check again on the road

    BoatUS suggests stopping to look over the rig shortly after you reach speed and checking periodically after that; the BoatUS Foundation says to check the straps and the bow eye whenever you stop.

Tie-down checklist before you tow

Run this list before you leave home and again before the drive back. It gathers the tie-down items from Discover Boating's trailering checklist (content from BoatUS), Sea-Doo's inspection page and Yamaha's 2021 Maintenance Matters pre-launch list, plus the other sources above.

Before you pull out

Trailering with the cover on

Two of the three craft makers mention a cover for the road. Sea-Doo's 2026 GTI and 2024 Spark operator's guides say a Sea-Doo cover can protect the watercraft, particularly when driving on dirt roads, to keep dirt from entering through the air inlet openings. Yamaha's 2021 Maintenance Matters guide says to protect a WaveRunner with a Yamaha storage cover when it isn't in use or when trailering.

Our Weatherproof Shield is a water-resistant cover sold as trailerable. The supplier's spec lists built-in buckles and straps, air vents to aid trailering, an elastic hem cord, a mesh storage bag and an extra strap set, in 600D solution-dyed polyester with a PU coating. Those buckles and straps hold the cover on the craft. They are not tie-downs: the craft still needs its winch strap, bow safety chain and transom straps on its own eyes, as described above. Covers are sized by overall length, and the size guide matches yours to a size. The cover carries a Lifetime warranty. The Satin Shield is our indoor cover (Satin storage bag included), so it isn't the one for the trailer. See all our jet ski covers.

Whether to tow with the cover on at all, and how to keep it in place, have their own guides: can you trailer a jet ski with the cover on and how to keep a cover from blowing off.

Trailerable Cover

AllGuard Weatherproof Shield Jet Ski Cover (Trailerable)

The trailerable cover: built-in buckles and straps hold the cover (not the craft), with air vents to aid trailering, an elastic hem cord and an extra strap set. Sized by length, P0 to P6.

4 colors: Blue / Black, Gray / Black, Red / Black, Yellow / Black

  • Under 90 inP0
  • Under 102 inP1
  • Under 115 inP2
  • Under 125 inP3
  • Under 135 inP4
  • Under 145 inP5
  • Up to 160 inP6

Lifetime Warranty

Jet ski tie-down FAQ

Secure it at both ends. Sea-Doo's 2026 GTI and 2024 Spark operator's guides say to tie the craft to both front and rear (bow/stern) eyelets. At the bow, that means the winch strap plus a safety chain or second strap on the bow eye; at the stern, transom straps from the stern eyes down to the trailer. BoatUS, Discover Boating and EZ Loader all describe securing a boat at the bow and at the stern, not with the winch alone.

Covering the craft for the trip?

The cover goes by your jet ski's overall length. Match the length in the size guide.

Open the size guide

Sources

  1. 2026 GTI, GTR and WAKE Series Operator's Guide: Transporting the Watercraft (p. 35); Mooring Cleats, Front Eyelet and grab handle (p. 137) (opens in a new tab)BRP (Sea-Doo) · 2026-10-27
  2. Spark Series 2024 Operator's Guide: Transporting the Watercraft (p. 31); Front and Rear Eyelets (pp. 73-74) (opens in a new tab)BRP (Sea-Doo) · 2026-10-27
  3. How do you launch & load a personal watercraft? (opens in a new tab)BRP (Sea-Doo) · 2026-10-27
  4. How to inspect your Personal Watercraft (trailer straps) (opens in a new tab)BRP (Sea-Doo) · 2026-10-27
  5. 2026 WaveRunner VX-C/VX/VX DELUXE/VX CRUISER/VX LIMITED Owner's/Operator's Manual, U.S.A. Edition, LIT-18626-15-77: Bow eye, Stern eyes, Cleat (p. 65); Transporting on a trailer (p. 75) (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2026-10-27
  6. Maintenance Matters: A Simple Guide for the Longevity of Your WaveRunner (2021): pre-launch checklist; cables and winches (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2026-10-27
  7. JET SKI STX 160 Owner's Manual, JT1500R/S/T (2022): Transporting (pp. 119-120) (opens in a new tab)Kawasaki Motors Corp., U.S.A. · 2026-10-27
  8. EZ Loader Boat Trailers Owner's Operation Manual (2006; PDF modified 2012): Using Safety Chains (p. 10); Tying Down Your Boat (p. 12); Winch Adjustment and Use (p. 13); Launching and Loading (pp. 16-18) (opens in a new tab)EZ Loader · 2026-10-27
  9. Tie Downs (BoatUS Magazine, July 2012) (opens in a new tab)BoatUS · 2026-10-27
  10. Transportation & Trailering (study guide) (opens in a new tab)BoatUS Foundation · 2026-10-27
  11. Your Ultimate Trailering Checklist (content courtesy of BoatU.S.) (opens in a new tab)Discover Boating (NMMA) · 2026-10-27
  12. How to Tow a Boat (opens in a new tab)Discover Boating (NMMA) · 2026-10-27
  13. Boat Trailer Tips (opens in a new tab)Discover Boating (NMMA) · 2026-10-27
  14. Boat Ramp Etiquette (opens in a new tab)Discover Boating (NMMA) · 2026-10-27
  15. How to Thread Ratchet Straps and Cam Buckle Straps (blog post dated May 30, 2012; general cargo guidance) (opens in a new tab)US Cargo Control · 2026-10-27

Find Your Size

Measure your jet ski bow to stern in a straight line, then enter the length in inches.

  1. Under 90 inP0
  2. Under 102 inP1
  3. Under 115 inP2
  4. Under 125 inP3
  5. Under 135 inP4
  6. Under 145 inP5
  7. Up to 160 inP6
Full Size Guide

In inches. Decimals are fine.

Covers for Your Jet Ski

All Covers