Trailering

How to Tow a Jet Ski: Loading, Trailering, Launching

Seat the craft on the bunks, secure it at bow and stern, check the rig before and during the trip, then launch and load at the ramp without holding up the line. Each step names the maker or group behind it.

By Alex Quinn 21 min read

Jet ski on a galvanized single trailer outside a lakeside cabin among pines, under a blue and black AllGuard Weatherproof Shield cover

Towing a jet ski comes down to four jobs: seating the craft properly on its trailer, securing it for the road, checking the rig before and during the drive, and launching and loading at the ramp. This guide takes them in that order, using what the craft makers (Sea-Doo, Yamaha and Kawasaki), the trailer maker EZ Loader (its boat-trailer owner's manual is a 2006 document, revised 2012), the BoatUS Foundation and Discover Boating (the National Marine Manufacturers Association's consumer site) publish. EZ Loader, the BoatUS Foundation and Discover Boating write about boat trailers in general, not jet skis in particular. Where their instructions differ, each one is named.

Still choosing the rig? Start with the jet ski trailer buying guide and jet ski trailer size and dimensions.

Note

Your manuals have the final word

Each step below names the manual or group it comes from. Your craft's owner's manual and your trailer's owner's manual have the final word for your rig, and your state's rules settle the legal points, such as trailer brakes and towing speed.

What you need before you tow a jet ski

Three ratings have to line up: the trailer's, the hitch's and the tow vehicle's.

The trailer. Kawasaki's 2022 STX 160 owner's manual says to make sure the trailer matches the craft's weight and hull design. EZ Loader's 2006 trailer owner's manual says the total weight of the trailer, the craft, its fuel and its gear must not exceed the trailer's GVWR (gross vehicle weight rating), which EZ Loader prints on the VIN decal at the left front of its trailers. For weights by model, see how much a jet ski weighs: its worked example, a Sea-Doo GTI 130 with a full tank on a Karavan steel single trailer, comes to about 1,068 lb before gear.

The hitch and ball. EZ Loader says the correct ball size and capacity are marked on the coupler, and that the hitch ball and hitch ratings must be the same as or more than the trailer's GVWR.

The tow vehicle. Sea-Doo's 2026 GTI, GTR and WAKE operator's guide tells owners to respect the tow vehicle's maximum weight capacity and tongue weight capacity as its manufacturer recommends, and to check the towing laws where they live, especially on the brake system, tow vehicle weight and mirrors. Discover Boating adds that the vehicle owner's manual gives the gross combined weight rating (GCWR): the limit for the vehicle, the loaded trailer, and the people and gear in the vehicle.

How to seat a jet ski on the trailer bunks

EZ Loader names two basic ways a trailer supports the hull, bunks or rollers, and describes bunks as long supports, usually wood or aluminum, with a carpet or plastic-like surface. A winch stand with a bow stop holds the front. How the hull sits on them matters for every mile of the trip.

  • Support the whole hull. Sea-Doo's 2026 operator's guide says to adjust the span and width of the bunks to support the hull along its full length, and not to let the bunk ends run past the end of the craft. Yamaha's 2021 Maintenance Matters guide says the bunks or rollers should keep proper contact with the bottom of the hull, to prevent hooks or rockers forming in its surface over time.
  • Level side to side. EZ Loader says the bunks should carry the weight evenly; if one side of the craft sits higher than the other, adjust the bunks to the same height.
  • Balanced front to back. Sea-Doo says to position the trailer wheels so the craft's center of gravity sits slightly ahead of them. EZ Loader and the BoatUS Foundation, writing about boat trailers in general, both put 5 to 10 percent of the loaded total on the hitch ball, with the tongue level. For the 1,068 lb GTI rig above, that's about 53 to 107 lb (our arithmetic: 1,068 x 0.05 and x 0.10). EZ Loader says a bathroom scale under the coupler can check it on lighter loads.
  • Bow eye under the bow stop. EZ Loader says to set the winch height so the strap runs level with the bow eye when the craft rests on the trailer, with the bow stop roller or vee block just above the eye. The winch should pull the bow eye straight in, without lifting or pulling down the bow.
  • Carried upright. Sea-Doo's guide says to carry the watercraft in its normal operating position.

EZ Loader gives a quick test: if the winch strap and tie-downs are tight and you can still rock the craft on the trailer, check the bunk and winch settings. The BoatUS Foundation explains why the balance matters: too much weight on the ball makes the tow vehicle hard to steer, and too little makes the trailer prone to fishtailing.

Empty galvanized single jet ski trailer on a driveway, with two gray carpeted bunks, a winch stand with a bow stop, and a tongue jack

Securing the jet ski for the road

All three craft makers' manuals cited here tie the craft down at its bow and stern eyes. Sea-Doo's 2026 operator's guide says to tie the watercraft to both the bow and stern eyelets so it's firmly secured, and to add tie-downs if necessary. Yamaha's 2026 VX owner's manual and Kawasaki's 2022 STX 160 owner's manual both say to fasten the craft to the trailer only by the bow eye and stern eyes.

  • Protect the finish. Sea-Doo and Yamaha both say to wrap ropes or tie-downs with rags or towels where they touch the body. Sea-Doo adds: don't route them over the seat or attach them to the grab handle.
  • Latch everything. Sea-Doo says to make sure the fuel cap, front storage cover, glove box, boarding platform and seat are latched, and to secure or remove accessories and cargo so nothing falls onto the road.
  • Don't trust the winch alone. The BoatUS Foundation says winches are made for loading and unloading, not for holding the boat on the trailer on the road, and recommends a separate line from the bow eye down to the trailer. EZ Loader says to attach the bow safety chain once the winch has pulled the craft against the bow stop, and to tie the stern down in both a downward and forward direction at the trailer's rear tie-down points.

Strap types, transom straps and a tie-down checklist are in how to tie down a jet ski on a trailer.

Drain plugs: the makers differ. Sea-Doo's operator's guide says to unscrew the drain plugs whenever the craft is on the trailer, so bilge water can drain out and condensation is reduced. Yamaha's 2026 VX manual describes draining the bilge on land with the stern drain plugs out and the bow raised, then reinstalling the plugs. All three manuals say the plugs must be secure before the craft goes back in the water, so follow your own manual and make the plugs part of your launch routine.

The cover. Yamaha's 2021 Maintenance Matters guide says to protect a WaveRunner with a Yamaha storage cover when it's not in use or when trailering, and Sea-Doo's operator's guide says a Sea-Doo cover can keep dirt from entering the air inlet openings, particularly on dirt roads. Our Weatherproof Shield is sold as a trailerable cover. Its supplier spec lists built-in buckles and straps, air vents to aid trailering, an elastic hem cord and an extra strap set, in water-resistant 600D solution-dyed polyester with a PU coating. The Satin Shield is an indoor cover, not one for the road.

Whether to tow with a cover on, and how to keep it in place, have their own guides: can you trailer a jet ski with the cover on and how to keep a cover from blowing off. Our jet ski covers are sized by overall length, and the size guide matches yours to a size.

Trailerable Cover

AllGuard Weatherproof Shield Jet Ski Cover (Trailerable)

Sold as a trailerable cover: built-in buckles and straps, air vents to aid trailering, an elastic hem cord and an extra strap set.

4 colors: Blue / Black, Gray / Black, Red / Black, Yellow / Black

  • Under 90 inP0
  • Under 102 inP1
  • Under 115 inP2
  • Under 125 inP3
  • Under 135 inP4
  • Under 145 inP5
  • Up to 160 inP6

Lifetime Warranty

Pre-trip checks for long-distance towing

Run the same list before every trip, and again before the drive home. Each item names who recommends it.

Before you pull out

Between trips, the bearings, lights, tires and winch strap need regular care: see jet ski trailer maintenance.

Checks en route and towing speed

On a long tow, every fuel stop is a check stop. The BoatUS Foundation says to make a habit of checking the wheel hubs each time you stop for gas: if one hub feels hotter than the other, or both feel abnormally hot, have the bearings inspected before you go on. Discover Boating calls excessive hub heat the main warning sign that the bearings are losing grease and overheating, or that a brake pad is engaged.

At the same stops, the BoatUS Foundation says to check the straps, the bow eye, the lug nuts and the nuts and bolts on the trailer frame, and in rain to check the cover for pooling water, which can affect weight distribution. Discover Boating adds a check of the trailer lights now and then during the trip.

Hand resting on the center of a trailer wheel at a roadside stop to feel for heat, a covered jet ski above the fender

Driving. The BoatUS Foundation's advice is to slow down, swing wider at corners, leave more room to the vehicle ahead and use lower gears rather than the brakes on downhills. EZ Loader suggests at least 4 seconds of following distance, or 5 in bad weather. If the trailer starts to sway, EZ Loader says to let off the gas, not to brake or turn the wheel to fight it, and to steer straight ahead just enough to stay in your lane; it notes that sway happens most often at higher speeds.

How fast. There's no single towing speed limit across the US. EZ Loader says to observe the posted limits at a minimum, and the BoatUS Foundation notes that some states have separate speed limits for cars pulling trailers. Two examples, from each state's own code:

Examples only, not a full list: towing speed limits vary by state. Lower posted limits still apply, and state codes change, so check your own state's vehicle code or DMV before a long trip.
StateTowing speed capWhat the law saysSource, date
California55 mphVehicle Code 22406(b): no one may drive a passenger vehicle or bus drawing any other vehicle on a highway faster than 55 mph. The DMV driver's handbook gives the same 55 mph for vehicles towing trailers.California Vehicle Code (archived copy, 2026-10-02) and DMV Driver's Handbook, read 2026-10-27
Washington60 mph (vehicles in combination)RCW 46.61.410(2): the limit for "vehicles over ten thousand pounds gross weight and vehicles in combination except auto stages" shall not exceed 60 mph and may be set lower; under (3), "trucks" on speed signs means those vehicles. The statute doesn't define "vehicles in combination"; check with Washington's DOL or State Patrol whether your rig counts.Revised Code of Washington, read 2026-10-27

Launching a jet ski at the ramp

Ramp time is shared time. Sea-Doo's launch-and-load guide says the main mistake new or inconsiderate ramp users make is arriving unprepared and holding up the lane, so most of the work happens before you reach the water. Sea-Doo starts at home: its launch-and-load page suggests briefly starting the craft on the trailer to check the battery and that it runs smoothly, checking the fuel, removing the cover, and packing life vests and dock lines. Its 2026 operator's guide, in its instructions for a craft out of the water, says never to run the engine without supplying water to the exhaust system, and never for longer than 2 minutes. The other makers set limits too: Yamaha's 2026 VX manual says not to run the engine over 4000 r/min on land, nor for more than 15 seconds without supplying water, or the engine could overheat, and Kawasaki's 2022 manual says not to run it with the craft out of the water for more than 15 seconds at a time; Kawasaki's 2026 STX 160 manual's flushing procedure, with a garden hose connected, has the engine idle for several minutes with the water running. Where the web tips and the manual differ, follow your owner's manual before running the engine out of the water.

Launch a jet ski in six steps

  1. Step 1: Prep the craft in the staging area

    Pull into a designated pre-launch area, or out of the way of ramp traffic (Sea-Doo). Remove the transom tie-downs, install the drain plugs, attach the safety lanyard and tie longer dock lines to the craft's tie-down points (Sea-Doo; Kawasaki says to attach a bow line). Kawasaki also says to ventilate the engine compartment for several minutes after transporting, with the storage lid open and the seats removed.

  2. Step 2: Prep the trailer and check the ramp

    Discover Boating and the BoatUS Foundation list unplugging the trailer lights as a staging step; EZ Loader notes that unplugging also disables electric trailer brakes, if the trailer has them. Keep the winch strap and bow safety chain hooked up until the trailer is at the water (EZ Loader). Kawasaki's manual says to check the ramp's surface, slope and width for both the trailer and the tow vehicle before launching, and on a first visit Discover Boating suggests parking out of the way to look over the ramp and dock and check the water depth.

  3. Step 3: Back down when it's your turn

    Wait your turn, then back into an open lane (Kawasaki, Sea-Doo). Sea-Doo says to back down until the craft's transom is in the water. Discover Boating's rule of thumb on most ramps is to stop when the front of the fender reaches the water, keeping the tow vehicle's rear wheels out of it, and EZ Loader notes that bunk trailers need more depth than roller trailers, enough for the craft to float. To steer the trailer in reverse, the BoatUS Foundation says to push the bottom of the steering wheel the way you want the trailer to go. If the hubs have no bearing protectors, it says it's best to keep them out of the water, and if you must dunk them, to let them cool first so cold water isn't drawn inside.

  4. Step 4: Secure the tow vehicle

    Sea-Doo says to put the tow vehicle in Park with the emergency brake on. The BoatUS Foundation adds a tire stop and leaving the engine running, and Discover Boating suggests wheel chocks.

  5. Step 5: Release the winch strap

    Sea-Doo says to unhook the winch strap from the bow eye so the craft can float off the bunks; Kawasaki says to unlock the winch and push the craft slowly off the trailer. EZ Loader warns that on slick plastic-covered bunks the craft can start to slide as soon as the strap is released, and Yamaha's 2026 VX manual says someone should make sure waves don't push the craft into the trailer. Keep hold of the dock line.

  6. Step 6: Clear the ramp

    A crew member walks the craft to the dock on its line while the driver parks the rig (Sea-Doo). Kawasaki's manual puts it plainly: move the craft to a docking or loading area, park the tow vehicle and don't block the ramp. Start the engine only in water deep enough for your make (next section).

Minimum water depth to start a jet ski

Each of the three makers' manuals sets a minimum depth for starting and running the engine. Sea-Doo's 2026 guide says keeping that depth stops sand, pebbles and rocks being drawn up into the jet pump. Yamaha's 2026 VX manual says shallower water can let pebbles or sand be sucked into the jet intake, damaging the impeller and overheating the engine; Kawasaki's says sand or debris from the bottom can damage the pump and impeller and possibly clog cooling lines.

From each maker's manual for the models named. Check the figure in your own manual.
MakerMinimum depthHow it's measuredDocument
Sea-Doo90 cm (3 ft)Under the lowest rear portion of the hull, with all passengers aboard, before starting the engine2026 GTI, GTR and WAKE Operator's Guide
Yamaha60 cm (2 ft)From the bottom of the watercraft; never run the engine in shallower water2026 VX Owner's/Operator's Manual
Kawasaki0.8 m (2.6 ft)Water depth when starting the engine or riding2022 STX 160 Owner's Manual

The three figures aren't measured the same way, so they don't compare directly: Sea-Doo's is under the hull with everyone aboard, Yamaha's from the bottom of the craft. Sea-Doo notes that the hull sits lower in the water with all passengers aboard. Coming in to a beach, Sea-Doo says to shut the engine off before the water under the lowest rear of the hull gets shallower than 90 cm (3 ft), then pull the craft in.

How to load a jet ski on a trailer

Loading is launching in reverse, and the same ramp manners apply. In Sea-Doo's guide, the tow vehicle driver is dropped off at the dock while the riders wait with the craft somewhere out of the way; Discover Boating suggests tying up at a courtesy dock away from the launch lane.

Load a jet ski in five steps

  1. Step 1: Back the trailer in, not as deep

    When it's your turn, back down an empty lane and secure the vehicle (Sea-Doo). For bunk boat trailers, EZ Loader says you probably won't need to go as deep as for launching: back in until the rear of the bunks is in the water, and the boat will center itself on the bunks about a third to half of the way onto the trailer. Discover Boating also warns against submerging the trailer too deeply, and the BoatUS Foundation says to make sure the trailer lights are unplugged before you back down.

  2. Step 2: Bring the craft onto the bunks

    Guide the craft onto the bunks. In its general boat-trailering advice, the BoatUS Foundation suggests lining a boat up with the trailer using its bow and stern lines, and advises against driving it onto the trailer under power, saying that erodes the ramp, can draw debris into the engine and can cause an accident. It isn't written for jet skis, so check what your craft's manual says, and mind the minimum depths above.

  3. Step 3: Hook the winch strap to the bow eye

    Unlock the winch, unwind enough strap to reach the bow eye and clip it on, keeping at least three turns of strap on the drum (EZ Loader). Lock the winch before cranking, then wind the craft in until the bow is pulled firmly against the bow stop. The BoatUS Foundation says to keep everyone out of the strap's direct line, because a strap or cable that breaks can whip back.

  4. Step 4: Chain the bow, then pull out

    With the winch locked, connect the bow safety chain before you drive up the ramp (EZ Loader). Discover Boating's ramp etiquette guide lists pulling up the ramp before the bow strap and safety chains are secure as a don't. Once the riders are clear, drive to a parking space or post-launch area (Sea-Doo).

  5. Step 5: Finish away from the ramp

    Away from the ramp, Sea-Doo's guide says to remove the dock lines, loosen the drain plugs, unload loose gear and attach the transom tie-downs. Reconnect the trailer lights (BoatUS Foundation), then run the pre-trip checklist again before the drive home (Discover Boating).

Clean, drain and dry before you leave. Sea-Doo's 2026 operator's guide says to remove any visible plants, animals, mud and debris from the craft (including the hull, intake grate and jet pump nozzle) and from the trailer before leaving the water body, drain all water from the craft, and let everything dry completely (5 days or more, checking local laws) before visiting another body of water. Discover Boating's ramp-etiquette guide lists Clean, Drain, Dry as a step too; check your state's and local rules.

With the craft strapped down, the cover can go back on for the drive home.

Moving a jet ski without a trailer

The transport sections of the Sea-Doo, Yamaha and Kawasaki manuals cited here are written for trailers, and Sea-Doo's 2026 guide says to carry the craft in its normal operating position. Truck beds, ramps and dollies have their own guide: how to transport a jet ski without a trailer.

If "tow" means pulling a jet ski on the water, for example after a breakdown, that's a different job with its own steps: how to tow a jet ski behind a boat.

Size the cover by length

The same bow-to-stern length that sizes a trailer sizes the cover. Find yours in the size guide.

Open the size guide

How to tow a jet ski: FAQ

There's no single US number: towing speed limits vary by state. Stay within the posted limit and any lower limit your state sets. Two examples: California's Vehicle Code section 22406 holds a passenger vehicle drawing another vehicle to 55 mph on a highway, and Washington's RCW 46.61.410 caps "vehicles in combination" at 60 mph. EZ Loader's boat-trailer manual (2006, revised 2012) notes that trailer sway happens most often at higher speeds, and the BoatUS Foundation's advice is to slow down. Check your own state's rules before a long trip.

Sources

  1. 2026 GTI, GTR and WAKE Series Operator's Guide: Transporting the Watercraft (pp. 35-36), Pre-Ride Inspection and Clean, Drain, Dry (pp. 37-44), Boarding from Shallow Water (p. 114), Starting (p. 117), Beaching (p. 125), Bilge Drain Plugs (p. 139), Flushing (pp. 155-156, 162) (opens in a new tab)BRP (Sea-Doo) · MY2026 guide (PDF dated 2025); read 2026-10-27
  2. How do you launch & load a personal watercraft? (opens in a new tab)BRP (Sea-Doo) · 2026-10-27
  3. Sea-Doo GTI: specifications (dry weight, fuel capacity) (opens in a new tab)BRP (Sea-Doo) · 2027 model page; read 2026-10-27
  4. 2026 WaveRunner VX-C/VX/VX DELUXE/VX CRUISER/VX LIMITED Owner's/Operator's Manual, U.S.A. Edition, LIT-18626-15-77: engine on land (pp. 31, 82), Draining the bilge water on land (p. 74), Transporting on a trailer (p. 75), Launching and Starting the engine on water (p. 87) (opens in a new tab)Yamaha Motor Corporation, U.S.A. · MY2026 manual; read 2026-10-27
  5. Maintenance Matters: A Simple Guide for the Longevity of Your WaveRunner (pre-ride checklist; trailer tips; storage cover) (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2021; read 2026-10-27
  6. JET SKI STX 160 Owner's Manual, JT1500R/S/T: Shallow Water (p. 31), Pre-Ride Check: engine out of the water (p. 88), Launching (p. 101), Transporting (opens in a new tab)Kawasaki Motors Corp., U.S.A. · 2022 manual; read 2026-10-27 (online flipbook)
  7. Boat Trailer Owner's Manual (hitching, safety chains, tie-downs, winch, tongue weight, tires, lug nuts, on the road, launching and loading) (opens in a new tab)EZ Loader Adjustable Boat Trailers · 2006 document (PDF created 2006-06-06, modified 2012-03-21), linked from ezloader.com; read 2026-10-27
  8. Single Watercraft Steel Trailer: specifications (GVWR, trailer weight) (opens in a new tab)Karavan Trailers · 2026-10-27
  9. MOVE I Extended 1500: specifications (GVWR) (opens in a new tab)Karavan Trailers · 2026-10-27
  10. Transportation & Trailering (Boating Safety Study Guide) (opens in a new tab)BoatUS Foundation · 2026-10-27
  11. Your Ultimate Trailering Checklist (content courtesy of BoatUS) (opens in a new tab)Discover Boating (NMMA) · 2026-10-27
  12. Boat Trailer Tips (opens in a new tab)Discover Boating (NMMA) · 2026-10-27
  13. How to Tow a Boat: Step-by-Step Guide (opens in a new tab)Discover Boating (NMMA) · 2026-10-27
  14. Boat Ramp Etiquette: Dos and Don'ts for a Smooth Launch (opens in a new tab)Discover Boating (NMMA) · 2026-10-27
  15. California Vehicle Code section 22406 (55 mph for a passenger vehicle drawing any other vehicle) (opens in a new tab)California Legislative Information · web.archive.org copy dated 2026-10-02 (the live leginfo page returned HTTP 403 to automated reads); read 2026-10-27
  16. California Driver's Handbook, Section 8: Safe Driving (Continued) (opens in a new tab)California DMV · 2026-10-27
  17. California Vehicle Code section 21715 (no passenger vehicle may tow more than one vehicle in combination) (opens in a new tab)California Legislative Information · as amended 1983; web.archive.org copy dated 2025-05-17 (the live leginfo page returned HTTP 403 to automated reads); read 2026-10-27
  18. Recreational Vehicles and Trailers Handbook, DL 648 (rev. 11/2011) (opens in a new tab)California DMV · revised 11/2011; read 2026-10-27
  19. RCW 46.61.410: Maximum speed limit for trucks, vehicles in combination (opens in a new tab)Washington State Legislature · 2026-10-27
  20. Transportation Energy Data Book, Edition 41: Table B.9 (a US gallon of gasoline weighs 6.2 lb) (opens in a new tab)Oak Ridge National Laboratory, US Department of Energy · 2025; read 2026-10-27
  21. 2026 Jet Ski STX 160LX/STX 160X Owner's Manual (99814-0205): Flushing the Cooling System (pp. 188-189) (opens in a new tab)Kawasaki Motors Corp., U.S.A. · 2026 model year; read 2026-10-27

Find Your Size

Measure your jet ski bow to stern in a straight line, then enter the length in inches.

  1. Under 90 inP0
  2. Under 102 inP1
  3. Under 115 inP2
  4. Under 125 inP3
  5. Under 135 inP4
  6. Under 145 inP5
  7. Up to 160 inP6
Full Size Guide

In inches. Decimals are fine.

Covers for Your Jet Ski

All Covers