Trailering

Can You Trailer a Jet Ski with the Cover On?

You can trailer a jet ski covered if the cover is made for it. What BoatUS, Discover Boating and the watercraft makers say about the risks on the road, and how to protect the finish.

By Alex Quinn 12 min read

Jet ski on its trailer at an empty roadside rest area, under a blue and black AllGuard Weatherproof Shield cover

Yes, you can trailer a jet ski with the cover on, if the cover is made for trailering and every strap is fastened. A loose storage cover is another matter. BoatUS Magazine says universal covers, cut with a generous fit so one model suits many boats, aren't generally suitable for trailering, while semicustom covers designed for specific hull shapes can be when they're properly secured. Yamaha makes the same point about personal watercraft: a cover that doesn't closely follow the craft's contours can be a hassle, or even dangerous, when towing.

Below: which covers can travel, short runs versus highway trips, what can go wrong on the road, how to protect the finish, and what the makers say about speed. For loading, the drive itself and launching, start with how to trailer a jet ski; for matching a trailer to the craft, see jet ski trailer size and dimensions.

Trailering covers vs storage covers

Discover Boating separates storage covers from trailering covers. Storage covers are designed to fit loosely, it says, because they protect boats at a dock or stored on a trailer. Trailering covers have a snug fit designed for traveling and are reinforced in high-wear areas to withstand traveling at high speeds, like on a highway. That is Discover Boating's description of the category, not a rating for any one cover, ours included.

Sea-Doo, Kawasaki and Yamaha all point owners to their own covers for trailering. On its New Zealand site, Sea-Doo describes its FishPro and Spark 2UP covers as weather-resistant trailering covers that protect the watercraft during storage and trailering. Kawasaki lists a vacuum-vented trailering system on its Jet Ski STX 160 cover for the extended deck. Yamaha's 2021 Maintenance Matters guide tells owners to protect a WaveRunner from the elements when not in use or when trailering by using a Yamaha WaveRunner storage cover made to fit the craft.

For boats in general, the BoatUS Foundation says that at highway speeds of 65 mph or more, anything loose on deck will probably be blown away, and suggests that, better yet, you wrap the boat in a snug-fitting cover, which it says protects the upholstery from sunlight and road grit and reduces fuel consumption.

Weatherproof Shield or Satin Shield: which can travel?

Our Weatherproof Shield is sold as a trailerable cover. It's made of water-resistant 600D solution-dyed polyester with a PU coating, in two-tone Blue, Gray, Red or Yellow with black, and it has air vents to aid trailering, built-in buckles and straps, an elastic hem cord and an extra strap set. It comes in seven sizes by overall length: measure bow to stern as described in how to measure a jet ski for a cover, then match the number in the size guide. The Weatherproof Shield has a Lifetime warranty; see the warranty page.

Our other cover, the Satin Shield, is an indoor cover and is not for trailering. It's black stretch fabric, 85% polyester and 15% spandex, with a sheared fleece interior, for a craft stored indoors. Of our two covers, the Weatherproof Shield is the one sold as trailerable. Both are in our jet ski covers collection.

Trailerable Cover

AllGuard Weatherproof Shield Jet Ski Cover (Trailerable)

Sold as trailerable: air vents to aid trailering, built-in buckles and straps, an elastic hem cord and an extra strap set. Water-resistant 600D PU-coated polyester, seven sizes.

4 colors: Blue / Black, Gray / Black, Red / Black, Yellow / Black

  • Under 90 inP0
  • Under 102 inP1
  • Under 115 inP2
  • Under 125 inP3
  • Under 135 inP4
  • Under 145 inP5
  • Up to 160 inP6

Lifetime Warranty

Short trips vs highway speeds

BoatUS Magazine's advice on trailerable covers is about standing up to the rigors of highway speeds. It illustrates the problem with a cheap tarp over a loaded pickup truck, which can quickly turn into a mess, usually shortly after the vehicle reaches cruising speed. The same article says boat covers that don't fit tight enough can allow air to get under the top during towing and cause it to pull free or fail at weak points.

Short trips. Sea-Doo's advice runs both ways. Its 2026 operator's guide, in the section on transporting the watercraft, says a Sea-Doo cover can protect the craft, particularly when driving on dirt roads, to prevent dirt entry through the air inlet openings. Its launch-and-load guide lists removing the cover among the jobs to do at home before you leave, as part of preparing before you reach the ramp so you don't hold up the ramp lane. Neither Sea-Doo page ties its advice to the length of the trip; on dirt roads, the operator's guide gives a reason to keep the cover on.

Highway trips. Use a cover made for trailering, fit it to a clean, dry craft and fasten every strap it has. BoatUS Magazine says it's important to use every strap point along the length of a cover to keep it secure at trailerable speeds, and that failing to, or overlooking a small tear or weak seam, can result in quick and dramatic failure down the road. Before a long trip, BoatUS Magazine suggests a shakedown: a run around the neighborhood and a leg on the highway at freeway speeds, then a check of the whole rig after the first 50 miles or so and at stops along the route.

Jet ski on its trailer at the end of a home driveway, under a gray and black AllGuard Weatherproof Shield cover

The risks: flapping, ballooning, chafing, pooling

Here are four ways a cover can go wrong on the road, and what each source says about them.

  • Flapping. Yamaha says that when a cover doesn't closely follow the craft's contours, wind may work its way under it and cause flapping, which can damage the craft's paint, graphics or gelcoat, or even tear the cover free unexpectedly. On its UK site, Kawasaki describes its Vacu-Hold trailering cover for the Ultra 310 as having no rippling and no whipping, and says it prevents strap damage to hulls.
  • Ballooning. This is air getting under the cover. BoatUS Magazine says covers that don't fit tight enough can allow air under the top during towing and cause it to pull free or fail at weak points. It also says support poles, which hold a cover up so it sheds water in storage, aren't recommended for towing because they often work free and leave the top loose. Kawasaki and Yamaha both describe a vacuum approach: Kawasaki's UK page says its Ultra 310 Vacu-Hold cover has a vacuum vent that creates negative pressure as the covered craft is trailered, keeping the cover tightly in place, and Yamaha says some covers may use vacuum technology to pull the cover tight against the craft, with no tie-downs needed when trailering.
  • Chafing. Rubbing wears both the cover and the finish under it. BoatUS Magazine says a cover for the road should have reinforcement patches on its underside where it's prone to premature wear from the rigors of the road, such as where the fabric touches cleats and windshields. In its winter cover test, the BoatUS Foundation suggests padding corners and sharp edges with pool noodles, old towels or sponges to reduce stress on the fabric and rubbing at wear points on the boat. Classic Accessories, a cover maker, recommends cleaning and drying a vehicle before installing its covers and says dirt, particles or debris left on the vehicle can be abrasive and wear paint and finishes in windy conditions or while trailering. The tie-downs matter too: Sea-Doo's 2026 operator's guide says to wrap ropes or tie-downs with rags or similar protectors where they can touch the watercraft body, and BoatUS Magazine says ratchet or cam straps of adequate size can keep a boat from bouncing on the trailer and suffering chafe damage.
  • Pooling water. On a rainy trip, the BoatUS Foundation says to check the boat's cover for pooling water, which could affect weight distribution and make the car more difficult to handle. Yamaha adds that a universal cover can be hard to fit without excess fabric that puckers or creates a pocket that holds rainwater. More on water under covers in water pooling and moisture under your cover.

For keeping a cover in place once the craft is parked, see keep your cover from blowing off.

How to protect the finish when you trailer covered

Each step comes from the sources above or from our own guidance for the Weatherproof Shield. The trailer tie-downs themselves are covered in how to tie down a jet ski on a trailer.

Trailering covered: five steps that protect the finish

  1. Step 1: Start with a clean, dry craft

    Classic Accessories recommends cleaning and drying a vehicle before you install its covers, and says dirt, particles or debris left on it can be abrasive and wear paint and finishes in windy conditions or while trailering. Rinse the hull and deck and dry them before the cover goes on.

    A hand drying the wet deck of an uncovered white jet ski on its trailer with a light-blue microfiber towel, a folded cover on the driveway
  2. Step 2: Tie the craft down

    A cover is not a tie-down. Sea-Doo's 2026 operator's guide says to tie the watercraft to both the bow and stern eyelets so it is firmly secured on the trailer, not to route ropes or tie-downs over the seat, and to wrap them with rags or similar protectors where they can touch the watercraft body.

  3. Step 3: Pad sharp edges

    In its winter cover test, the BoatUS Foundation suggests padding corners and sharp edges with pool noodles, old towels or sponges to reduce stress on the cover fabric and rubbing at wear points. Look over the craft for any sharp edge or add-on the cover will sit against.

  4. Step 4: Fasten every strap

    BoatUS Magazine says to use every strap point along the length of a cover to keep it secure at trailerable speeds. On the Weatherproof Shield, fasten every built-in buckle and strap before you drive.

  5. Step 5: Check at every stop

    The BoatUS Foundation says to check the trailer's wheel hubs every time you stop for gas and to make sure the straps holding the boat are tight, and in rain to check the cover for pooling water. BoatUS Magazine suggests stopping to look over the rig shortly after you reach speed and then periodically. At each stop, walk around the cover: check every built-in buckle is still fastened, and look for flapping edges, rubbing and standing water.

Note

Questions about trailering with our cover?

We don't publish a maximum trailering speed for the Weatherproof Shield. Fasten every strap, check the cover at each stop, and contact us through the contact page if you have a question about your trip.

How fast can you tow with the cover on?

None of the sources here gives one speed that suits every cover. The statements that do exist are about a maker's own product or about covers in general:

  • Kawasaki says the patented Vacu-Hold trailering system it has selected allows a Jet Ski to be trailered at highway speeds with no hold-down, and supplies J-channel clips for use when trailering behind a vehicle that causes extreme turbulence. That is Kawasaki's statement about its own Vacu-Hold cover, here the Ultra 310 version on its UK site.
  • Classic Accessories describes its StormPro trailerable boat cover as designed for both long-term storage and highway travel.
  • Discover Boating says trailering covers, as a category, are reinforced in high-wear areas to withstand traveling at high speeds, like on a highway.

The law can set a ceiling of its own: the BoatUS Foundation notes that some states have separate speed limits for cars pulling trailers. California, for example, limits any passenger vehicle drawing another vehicle to 55 miles per hour on the highway (Vehicle Code 22406). Check the rules in each state on your route; how to trailer a jet ski covers the drive itself.

Our Weatherproof Shield. It's sold as trailerable, with air vents to aid trailering and built-in buckles and straps. We don't publish a maximum trailering speed for it, so read the cover statements above as being about other makers' covers or about covers in general, not about ours. Fasten every strap, check the cover at each stop, and if you have a question about trailering with it, contact us.

Size the cover before the trip

Measure your jet ski's overall length, bow to stern, and match it in the size guide. The Weatherproof Shield comes in seven sizes.

Open the size guide

Trailering with the cover on: FAQ

Yes, with a cover made for trailering and every strap fastened. BoatUS Magazine says loose universal covers aren't generally suitable for trailering, and Discover Boating says trailering covers have a snug fit designed for traveling. Our Weatherproof Shield is sold as trailerable; our Satin Shield is an indoor cover and is not for trailering.

Sources

  1. Boat Covers That Work (Dan Armitage) (opens in a new tab)BoatUS Magazine · 2015-04
  2. Tips For Towing A Boat Trailer (Dan Armitage) (opens in a new tab)BoatUS Magazine · 2020-04
  3. Tie Downs (opens in a new tab)BoatUS Magazine · 2012-07
  4. Study guide: Transportation & Trailering (opens in a new tab)BoatUS Foundation · retrieved 2026-10-27
  5. Boat Covers for Winter Storage (gear test, 2021-22 winter) (opens in a new tab)BoatUS Foundation · 2022-09 (Foundation Findings #60); retrieved 2026-10-27
  6. Boat Covers: How to Choose the Best Option (Storage Covers vs. Trailering Cover) (opens in a new tab)Discover Boating (NMMA) · retrieved 2026-10-27
  7. How to Choose the Right PWC Cover (opens in a new tab)Yamaha Motor Corporation, USA (Yamaha WaveRunners) · 2023-10-10
  8. Yamaha WaveRunners 2021 Maintenance Matters Guide (Keep it covered) (opens in a new tab)Yamaha Motor Corporation, USA · 2021
  9. GTI, GTR and Wake Series Operator's Guide 2026 (Transporting the watercraft, p. 35) (opens in a new tab)BRP (Sea-Doo) · 2026
  10. How do you launch and load a Sea-Doo? (Before you leave the house) (opens in a new tab)BRP (Sea-Doo) · retrieved 2026-10-27
  11. Sea-Doo covers (FishPro and Spark 2UP covers), New Zealand site (opens in a new tab)BRP (Sea-Doo) · retrieved 2026-10-27
  12. Vacu-Hold Jet Ski Cover (Ultra 310), part 99994-1698 (opens in a new tab)Kawasaki Motors UK · retrieved 2026-10-27
  13. Jet Ski STX 160 Cover - Extended Deck, item 99994-2391 (opens in a new tab)Kawasaki Motors Corp., U.S.A. · retrieved 2026-10-27
  14. StormPro Heavy-Duty Trailerable Boat Cover (product page and FAQ) (opens in a new tab)Classic Accessories · retrieved 2026-10-27
  15. California Vehicle Code section 22406 (opens in a new tab)California Legislature (leginfo) · archived copy of 2026-10-02 (Wayback Machine); the live page returned HTTP 403 on 2026-10-27

Find Your Size

Measure your jet ski bow to stern in a straight line, then enter the length in inches.

  1. Under 90 inP0
  2. Under 102 inP1
  3. Under 115 inP2
  4. Under 125 inP3
  5. Under 135 inP4
  6. Under 145 inP5
  7. Up to 160 inP6
Full Size Guide

In inches. Decimals are fine.

Covers for Your Jet Ski

All Covers