AllGuard Weatherproof Shield
Outdoor storage and trailering
$139.99
Lifetime WarrantySizing
Covers are sized by overall length, so one straight-line measurement picks your size. Here's how to take it, what to count, and what to do near a size line.
Every jet ski cover on this site is sized by one number: your craft's overall length, measured bow to stern in a straight line. Measure once, carefully, and choosing a size takes seconds.
You'll need a tape measure long enough to span the craft (a 16 ft tape covers every size we make) and a pen. A helper makes it easier.
Measure overall length: a straight, level line from the farthest point at the front of the bow to the farthest point at the back, often the edge of the swim platform or rear bumper. Include anything that stays on the craft under the cover, and never run the tape over the seat or handlebars. Then match the number to a size on the jet ski cover size guide.
Put the craft on its trailer or a flat floor with the bow pointing straight ahead. Fold up any reboarding step or ladder the way it sits in storage.
Front: the tip of the bow or front bumper. Back: whatever sticks out farthest at the stern. That's often the swim platform or rear bumper, but it can be a tow hook or a mounted accessory.
Hold a level or a straight board upright against each end point and put a piece of masking tape on the floor directly below it. This keeps the curve of the hull out of your number.

Run the tape straight between the two marks. If you can't mark the ground beside a trailer, pull the tape tight along the side of the hull instead, kept level and straight.

Note the reading without rounding down. If your tape reads centimeters, divide by 2.54: 332 cm is about 130.7 in.
If the two readings differ, use the longer one. Near a size line, take a third reading.
The cover has to reach past both ends of everything under it. Count whatever will be on the craft when the cover goes on:
Tall add-ons such as a tow tower or a high rack change more than length. Read will the cover fit with accessories installed? or contact us with your measurements.
Each size is labeled with the lengths it fits, and the top number is the maximum. A craft that measures even a little over a line takes the next size up. For example, 130 in falls in P4 - 125 to 135 in.
Enter your measured overall length in inches.
| Overall Length | Size | Cover | Shop |
|---|---|---|---|
| Under 90 in | P0 | Weatherproof Shield Trailerable | Shop P0 in the Weatherproof Shield |
| Under 102 in | P11 seater | Weatherproof Shield Trailerable | Shop P1 in the Weatherproof Shield |
| Under 115 in | P21–2 seater | Weatherproof Shield Trailerable | Shop P2 in the Weatherproof Shield |
| Under 125 in | P32 seater | Weatherproof Shield Trailerable | Shop P3 in the Weatherproof Shield |
| Under 135 in | P43 seater | Weatherproof Shield Trailerable | Shop P4 in the Weatherproof Shield |
| Under 145 in | P53 seater+ | Weatherproof Shield Trailerable | Shop P5 in the Weatherproof Shield |
| Up to 160 in | P63 seater+ | Weatherproof Shield Trailerable | Shop P6 in the Weatherproof Shield |
| Under 117 in | PWC22–3 seater | Satin Shield Indoor | Shop PWC2 in the Satin Shield |
| Up to 138 in | PWC33–4 seater | Satin Shield Indoor | Shop PWC3 in the Satin Shield |
Measure bow to stern in a straight line. Within 1 in of a size line? Measure again before you order.
Tip
Size by length, not by type
A stand-up isn't automatically P0. Yamaha lists the 2027 SuperJet at 7 ft 9 in (93 in), which is P1, and Kawasaki lists the 2027 SX-R 160 at 104.5 in, which is P2. Seat count isn't a size either: go by the tape.
Trailerable Cover
AllGuard Weatherproof Shield Jet Ski Cover (Trailerable)
Trailerable cover sized P0 to P6 by overall length, with an elastic hem cord, built-in buckles and straps, and air vents to aid trailering.
4 colors: Blue / Black, Gray / Black, Red / Black, Yellow / Black
$139.99
Shop the Weatherproof ShieldThe Satin Shield indoor cover comes in two sizes: PWC2 - 2-3 Seater, up to 117 in, and PWC3 - 3-4 Seater, up to 138 in. Choose by your measured length, not the seat count in the name.
If your craft measures more than 138 in, choose the Weatherproof Shield instead; its sizes run to 160 in. Near the 117 in line, measure carefully: Yamaha lists the 2027 JetBlaster at 9 ft 8 in (116 in).

Indoor Cover
AllGuard Satin Shield Indoor Jet Ski Cover
Indoor stretch cover (85% polyester, 15% spandex) with a sheared fleece interior and elastic front and rear hems. Two sizes: up to 117 in and up to 138 in.
Color: Black
$129.99
Shop the Satin ShieldIf your number lands within 1 in of a size line, measure again before you order. Published lengths can vary by model year and trim, so your own tape measure is the final check.
More on this in my jet ski is between two cover sizes.
The published length is a good starting point, especially when you're nowhere near a size line. Use the exact model year and trim.
Two cautions. Lengths can change between generations of the same model name: Sea-Doo's 2017 GTX Limited spec sheet lists 139.2 in, while the 2027 GTX Limited page lists 135.8 in. And feet-and-inches figures give whole inches only, so treat them as approximate near a line. For some older model years, such as the 2004 and 2005 Kawasaki STX-15F, we couldn't find a manufacturer spec page that names the year; for those, measure.
Our make pages list sourced lengths by model: Sea-Doo jet ski covers, Yamaha WaveRunner covers and Kawasaki jet ski covers. Published lengths for popular models:
Lengths are the manufacturers' published figures. Your measured length is what counts, and "measure to confirm" marks lengths within 1 in of a size line.
Choose by overall length: measure bow to stern in a straight line, including the swim platform and anything that stays mounted. Weatherproof Shield sizes run from P0 - Up to 90 in to P6 - 145 to 160 in. The Satin Shield indoor cover comes in PWC2 (up to 117 in) and PWC3 (up to 138 in).
It depends on the model. In the manufacturer lengths on this page, current models range from 93 in (Yamaha SuperJet, listed as 7 ft 9 in) to 146.8 in (Sea-Doo FishPro Sport). Check the spec page for your exact model year, or measure.
Width varies by model. Kawasaki lists the 2027 SX-R 160 stand-up at 30.1 in wide, and Sea-Doo lists the 2027 GTI at 49.2 in. You don't need width to choose a cover size; sizes go by length.
Yes. Measure to the farthest point at the back, whether that's the swim platform, the rear bumper, a tow hook or an accessory that stays on under the cover. Sea-Doo's MY24 spec book describes its published length as bumper to bumper.
Size up. Over a line, even slightly, choose the next size up, and exactly on a line, take the larger size: 125 in is P4, not P3. If you're within 1 in under a line, measure again. The Satin Shield isn't offered over 138 in; exactly 138 in is PWC3.
Yes, as a starting point, if you use the exact model year and trim. Measure yourself if you're within 1 in of a size line or have accessories mounted.
Not to choose a size. If your craft carries something unusually tall or wide, such as a tow tower, a tall rack or wide sponsons, contact us with the measurements before you order.
Sizes go by overall length, bow to stern. The size guide has the full chart and how to measure.