Trailering

How to Transport a Jet Ski Without a Trailer

No trailer means a carrier rated for the craft, a truck that can take the weight and a load your state allows. Here is what the makers, federal labeling rules and state codes publish.

By Alex Quinn 24 min read

Jet ski under a blue and black AllGuard Weatherproof Shield cover, resting on a four-caster dolly with carpeted bunks in a garage

A jet ski can leave home without a trailer in two ways: in the bed of a pickup truck on a carrier built for the job, or on a wheeled dolly for short moves. Either way the craft is heavy and long, and three questions decide whether a setup works: what the craft weighs against what your truck may carry, what the makers say about lifting it and tying it down, and what your state requires for a load that hangs off the back.

This guide sticks to published sources: the carrier and gear makers' own product pages, the 2026 Sea-Doo, Yamaha and Kawasaki manuals, the federal labeling rules behind your truck's load limit, and state statutes, each with the date it was read. Where they say nothing, the guide says so and points you to your manual, your dealer or your state. For trailering itself, start with how to tow a jet ski.

Note

Examples, not recommendations

Products named here are examples from their makers' own pages, read on 2026-10-27 (the Sea-Doo Lift Kit from a June 2024 archived copy), not a ranking or an endorsement. Ratings, sizes and weights are the makers' figures. Your craft's owner's manual, your truck's owner's manual, the carrier maker and your dealer have the last word on your setup.

Can a jet ski ride in a truck bed?

The craft makers don't say. The transport instructions in the three 2026 manuals cited here are written for trailers. Sea-Doo's “Transporting the Watercraft” section covers the trailer bunks, the trailer wheels and tying the craft down on the trailer; Yamaha's 2026 VX manual titles its section “Transporting on a trailer”; and Kawasaki's 2026 STX 160 manual opens its transporting section with “When transporting the watercraft on a trailer, observe the trailer laws and regulations in your area.” A text search of the 2026 Sea-Doo GTI, GTR and Wake guide, the 2026 Yamaha VX manual and the 2026 Kawasaki STX 160 manual finds no mention of a truck or a pickup.

Equipment for carrying one in a pickup does exist. The one maker this guide found publishing jet ski specs for it is TruckBoss, which sells an aluminum deck that mounts in a pickup bed and FlexxLoader skids for jet skis. TruckBoss describes the FlexxLoader PWC Large as a 139-inch all-aluminum skid for full-size sit-down jet skis: you float the ski onto the skid at the water, secure it with tie-downs, and the deck's integrated winch pulls it up the ramp and onto the deck, where a self-locking track holds it. Here are the pieces as TruckBoss lists them.

From TruckBoss's own product, Our Decks and FAQ pages, read 2026-10-27. Dimensions and weights are TruckBoss's listed figures. One maker's system, shown as an example, not a ranking or an endorsement.
TruckBoss product (maker's page)What TruckBoss says it's forSizeWeight or rating
Expandable deckMounts in a mid- or full-size pickup bed; can carry two large PWCs or two small PWCs, among other loads5, 6, 7 and 8 ft decks for beds from 4 ft 10 in to 8 ft long; sides expand to as much as 102 inRated for 2,000 lb of distributed load; the deck itself weighs 350 lb (5 ft) to 500 lb (8 ft)
FlexxLoader PWC LargeFull-size sit-down jet skis, loaded from the water and winched onto a TruckBoss deck139 in long (listed 139 x 19 x 8 in)95 lb (listed product weight)
FlexxLoader XLSit-down PWCs, with a TruckBoss deck's integrated winch and ramp149 in long (listed 149 x 19 x 8 in)105 lb (listed product weight)
FlexxLoader PWC SmallStand-up jet skis, loaded from the water and winched onto a TruckBoss deckListed 110 x 16 x 8 in74 lb (listed product weight)
FlexxLoader RampOne of TruckBoss's ramps; its FAQ says its ramps load sleds, bikes or a fully loaded FlexxLoaderNot given with the ratingRated for 1,500 lb (680 kg)
FlexxLoader Buggy SystemTurns a FlexxLoader into a beach launch cart for sand, grass or uneven terrainListed 46 x 14 x 20 in75 lb (listed weight)

TruckBoss adds a caution about length. Its FAQ says that on a standard or short-bed truck, hauling a FlexxLoader with a PWC will likely need its Flip Extension “to safely support the full length of your setup.” Length comes up again under the state overhang rules below.

Other gear turns up in searches, such as overhead bed racks and powered in-bed lifts, but this guide found no maker page for one that publishes jet ski specs, so none is compared here. The checks below apply to any of them: the maker's rated capacity, the weight against your truck's payload, and the overhang.

Lifting and tie-down points: what the manuals say

Without a skid that's winched up from the water, getting a craft into a bed means lifting it, and the manuals answer that only in the negative. A text search of the 2026 Sea-Doo GTI, GTR and Wake guide, the 2026 Yamaha VX manual and the 2026 Kawasaki STX 160 manual finds no instructions for lifting the whole craft with a sling, hoist or crane, and none of them names a lifting point. They do name parts you must never lift it by, and Yamaha's and Kawasaki's warnings say the craft could fall and cause severe injury.

From each manual's equipment, general information and safety sections, read 2026-10-27. Yamaha's pull-up cleats are on the VX Cruiser and VX Limited.
Maker and manualPartWhat the manual says
Sea-Doo, 2026 GTI, GTR and Wake guideMooring cleatsCan be used for docking. Never use them to pull or lift the watercraft
Sea-Doo, same guideFront eyeletEyelets can be used for mooring, towing and as tie-down points when trailering. Do not use these eyelets to lift the watercraft
Sea-Doo, same guideMolded grab handleA handhold. Never use it to tow anything or to lift the watercraft
Yamaha, 2026 VX manualCleatFor a ski rope. Do not use it to lift the watercraft; it is not designed to support the craft's weight
Yamaha, same manualHandgrip, reboarding step, pull-up cleatsNot designed to support the craft's weight; do not use them to lift it
Kawasaki, 2026 STX 160LX/160X manualHandrailDo not lift the watercraft using the handrail (repeated on an on-craft warning label)
Kawasaki, same manualMulti-mount systemDo not lift the watercraft using it

Two of the makers' stores have listed lifting gear. BRP's U.S. store page for the Sea-Doo Lift Kit, as archived in June 2024, describes nylon webbing and vinyl-coated steel lift plates that hoist a Sea-Doo out of the water, with a lifting capacity of 1,200 lb (544 kg). Yamaha's store says the two zinc D-rings on its Deluxe Lift Harness connect to a davit or other suitable lifting mechanism, and rates the harness up to 1,000 lb. Neither product page's text says where the gear attaches to the hull or how to rig it, and this guide doesn't either.

Important

No lifting instructions here

This guide gives no sling, hoist or rigging advice. Sea-Doo, Yamaha and Kawasaki name parts that must not be used to lift the craft, but none of the manuals cited here says where a sling attaches. If the craft has to be lifted, follow the lifting gear maker's instructions and ask your dealer.

For tying down, the manuals point to the bow and stern eyes, in trailer terms. Describing its front eyelet, Sea-Doo's 2026 guide says eyelets can be used for mooring, towing and as tie-down points when trailering, and its transport section says to tie the watercraft to both front and rear (bow/stern) eyelets so that it is firmly secured on the trailer. Yamaha's 2026 VX manual says the bow eye is used to attach a rope when transporting, mooring or towing in an emergency, and the stern eyes when transporting or mooring; on a trailer, it says not to attach ropes or tie-downs to any other part of the craft. Kawasaki's 2026 STX 160 manual says to securely fasten the watercraft to prevent movement between the craft and trailer, to use only the bow and stern eyes when fastening it to the trailer, and not to use the handrail to attach tie-downs, as that can damage the handrail and/or hull.

None of them covers a truck bed. On a carrier, follow the carrier maker's instructions: TruckBoss's FlexxLoader pages say to secure the ski on the skid with tie-downs before winching it up. Strap types, padding and a tie-down checklist are in how to tie down a jet ski on a trailer.

Two hands checking the steel ratchet buckle of a black tie-down strap above two coiled straps on a workbench

Jet ski weight vs your truck's payload

The number that decides whether a truck can carry a jet ski is printed on the truck, not the craft. Start with the craft. Spec pages give its weight one of two ways: Sea-Doo and Yamaha publish a dry weight, without fuel, and Kawasaki also publishes a curb weight, which by its own footnote includes all necessary materials and fluids to operate correctly, a full tank of fuel (more than 90 percent capacity) and the tool kit, if supplied. To a dry weight, add the fuel: the Transportation Energy Data Book, published by Oak Ridge National Laboratory for the US Department of Energy, gives the weight of a US gallon of gasoline as 6.2 lb. How much does a jet ski weigh? lists more models.

Weights and tank sizes from each maker's spec page, read 2026-10-27, as tabled in our jet ski weight guide. Fuel at 6.2 lb per US gallon (Transportation Energy Data Book, Edition 41), rounded to the nearest pound; our arithmetic.
Craft (maker's spec page)Published weightFull tank at 6.2 lb per gallonCraft with fuel
Yamaha SuperJet375 lb dry5 gal: 31 lb406 lb
Sea-Doo Spark for 2 (60 hp), 2027437 lb dry7.9 gal: 49 lb486 lb
Sea-Doo GTI (130 hp), 2027741 lb dry18.5 gal: 115 lb856 lb
Kawasaki Ultra 310LX, 2026996.7 lb estimated dry; 1,137.8 lb curbIncluded in the curb weight1,137.8 lb (curb)

Then find your truck's limit. Under the federal tire-labeling standard, FMVSS No. 110, a vehicle with a gross vehicle weight rating of 10,000 lb or less carries a placard on the driver's side B-pillar, the door pillar behind the driver's door; where it can't go there, the standard lists other spots, such as the rear edge of the driver's door. The placard states the vehicle's capacity weight as “The combined weight of occupants and cargo should never exceed XXX kilograms or XXX pounds.” For vehicles made on or after September 1, 2005, federal rules also require the owner's manual to explain load limits, including the adverse safety consequences of overloading on handling, stopping and tires, and to print a set of steps for using the placard figure, summarized here.

Check a load against your truck's placard

  1. Step 1: Find the figure

    Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle's placard.

  2. Step 2: Subtract the people

    Determine the combined weight of the driver and passengers who will ride in the truck, and subtract it from that figure. The result is the available cargo and luggage load capacity.

  3. Step 3: Weigh the cargo against it

    Determine the combined weight of the cargo. That weight may not safely exceed the available capacity from the previous step.

  4. Step 4: Allow for a trailer

    If the truck will also tow a trailer, load from the trailer is transferred to the truck; the federal steps say to consult the owner's manual for how much that reduces the available cargo capacity.

In a pickup carrying a jet ski, the cargo is more than the craft. TruckBoss lists its deck's own weight and says optional accessories “will add to the total system weight”, so count the carrier, its winch and anything else in the bed. Here is the cargo side for three example setups, from the published weights above.

Our arithmetic from the craft table above and TruckBoss's listed deck and skid weights, read 2026-10-27, before the winch, other accessories, people and gear. Weights only, not a fitment check: whether a skid suits a given craft, deck and bed is a question for TruckBoss.
Example setupCraft with fuelTruckBoss deckFlexxLoader skidTotal in the bed
Yamaha SuperJet, 6 ft deck, PWC Small406 lb400 lb74 lb880 lb
Sea-Doo GTI (130 hp), 8 ft deck, PWC Large856 lb500 lb95 lb1,451 lb
Kawasaki Ultra 310LX, 8 ft deck, XL1,137.8 lb500 lb105 lb1,742.8 lb

Set the last column, plus the winch, accessories and gear, against what the placard leaves after the people aboard. TruckBoss rates the deck itself for 2,000 lb of distributed load, but its FAQ is plain about which limit counts: “the limiting factor isn't the deck—it's your truck.” TruckBoss adds that your vehicle's payload capacity ultimately determines how much weight you can safely carry.

Overhang, flags and load laws by state

A full-size jet ski is long next to a pickup bed. TruckBoss sizes its decks for beds from 4 ft 10 in to 8 ft (96 in) long. Sea-Doo lists the 2027 GTI at 130.7 in long, and Kawasaki the 2026 Ultra 310LX at 140.9 in. On a carrier, the load is as long as the carrier or the craft, whichever reaches farther: TruckBoss lists its PWC Large skid alone at 139 in.

Whatever extends past the back counts under your state's projecting-load rules. As a rough guide, if the craft rests fully in the bed with its bow at the front, the part past the end of the bed is the craft's length minus the bed's length: a 130.7 in craft would extend about 34.7 in past a 96 in bed, and about 56.7 in past a 74 in (6 ft 2 in) bed. Measure your own loaded truck the way your state measures: Illinois and Virginia, and the lamp rules in Florida and Washington, measure past the bed or body; California measures from the taillamps.

Examples only, not a full list: projecting-load and load-securing rules vary by state, and codes change. Each row is the state's own code, read on 2026-10-27. Check your own state's vehicle code or DMV before you load.
State and lawWhat it saysSource, as of
California Vehicle Code 24604A load that extends to the rear 4 ft or more beyond the rear of the vehicle, as measured from the taillamps: during darkness, two red lights at the extreme end of the load, visible from at least 500 ft to the sides and rear; at any other time, a solid red or fluorescent orange flag or cloth at least 18 in square, and two flags or cloths if the projecting load is wider than 2 ftCalifornia Legislative Information; amended 2015, effective 2016; read 2026-10-27
California Vehicle Code 35410The load on a motor vehicle alone may not extend to the rear beyond the last point of support by more than two-thirds of the vehicle's wheelbaseCalifornia Legislative Information; enacted 1959; read 2026-10-27
Florida Statutes 316.228A load that extends to the rear 4 ft or more beyond the bed or body: at the times lamps are required, two red lamps and two red reflectors at the rear and a red lamp on each side; at all other times, red flags at least 18 in square marking the extremities of a load more than 4 ft beyond the rear. A violation is a noncriminal traffic infractionThe Florida Senate, 2025 Florida Statutes; read 2026-10-27
Florida Statutes 316.520A vehicle may not be driven or moved on any highway unless it is constructed or loaded so as to prevent any of its load from dropping, shifting, leaking, blowing or otherwise escapingThe Florida Senate, 2025 Florida Statutes (last amended 2020); read 2026-10-27
Illinois, 625 ILCS 5/12-204A load that extends to the rear 4 ft or more beyond the bed or body: at the times lighting is required, a red light or lantern visible from at least 500 ft to the sides and rear; at any other time, a red flag or cloth at least 12 in squareIllinois General Assembly (Source: P.A. 77-37); read 2026-10-27
Virginia Code 46.2-1121On a vehicle other than a commercial motor vehicle, a load more than 4 ft beyond the rear of the bed or body: a red flag at least 12 in long and 12 in wide at the end of the load, clearly visible from the rear at all times; between sunset and sunrise, a red light visible in clear weather from at least 500 ft to the sides and rearVirginia Legislative Information System (last amended 2022); read 2026-10-27
Washington RCW 46.37.140A load more than 4 in beyond the sides or more than 4 ft beyond the rear: red or orange fluorescent warning flags at least 18 in square marking its extremities. A load 4 ft or more beyond the bed or body: at the times lamps are required, two red lamps, two red reflectors and a red lamp on each sideWashington State Legislature (last amended 2014); read 2026-10-27
Washington RCW 46.61.655No one may operate a vehicle with any load on a public highway unless the load is securely fastened to prevent it from becoming loose, detached or in any manner a hazard to other users of the highway. Failing to secure a load is an infraction; failing to secure it with criminal negligence is a misdemeanor if that causes damage to another's property, and a gross misdemeanor if it causes substantial bodily harm to anotherWashington State Legislature (last amended 2005); read 2026-10-27

Even across these five states the details differ. The flag must be at least 12 in square in Illinois (625 ILCS 5/12-204) and, for a vehicle other than a commercial motor vehicle, Virginia (Code 46.2-1121), and at least 18 in square in California (Vehicle Code 24604), Florida (Statutes 316.228) and Washington (RCW 46.37.140); California measures from the taillamps (Vehicle Code 24604); and California also limits how far a load may reach behind its last point of support (Vehicle Code 35410). None of these sections mentions jet skis or says whether one may ride in a pickup. They set what a projecting load must carry, how far it may reach and that it must be secured. Your own state's vehicle code or DMV has the rule that applies to you.

Square red cloth flag on a wooden dowel beside two coiled ratchet straps and a coil of bungee cord on a workbench

DIY jet ski truck bed ramps

This guide gives no plans, dimensions or load ratings for a homemade ramp. None of the three craft manuals cited here publishes any, and a homemade ramp comes with no rating for a load that, for the two full-size craft in the weight table above, comes to 856 to 1,137.8 lb with fuel before any cart or carrier.

Ramps sold for loading pickups carry their maker's rating and conditions, and the conditions matter as much as the number. TruckBoss rates its FlexxLoader Ramp at 1,500 lb (680 kg), as part of its own deck and skid system. A general-purpose loading ramp can rule a jet ski out entirely: Harbor Freight's manual for its item 60397 loading ramps says they are for use with 2-wheeled dirt bikes and 4-wheeled ATVs only, lists a capacity of 1,000 lb combined and 500 lb individually (static conditions) and a 42 in maximum tailgate height, and says to use the ramps as intended only, connect safety chains and not exceed the tailgate's weight capacity.

So read a ramp maker's intended uses before its rating. If no ramp maker rates a product for your load and setup, ask the carrier maker or your dealer rather than improvising one.

Dollies for short moves

For moving a craft around a garage, a yard or a short stretch of hard ground, a wheeled dolly does without a truck at all. C.E. Smith, for example, describes its PWC dolly as a way to move a small vessel such as a jet ski around on any hard surface. Dolly makers' capacities, bunk spacing and the weight checks are compared in how to store a jet ski without a trailer, so they aren't repeated here; the one to remember is to check a dolly's stated capacity against the craft's weight with fuel, not its dry weight.

For getting a craft from a truck to the water across a beach, TruckBoss sells a Buggy System that turns a FlexxLoader into a beach launch cart, which it says can cross sand, grass or uneven terrain. If the move involves a trailer you already own, how to tow a jet ski covers moving the trailer by hand.

White jet ski on a four-caster dolly with carpeted bunks, rolled out onto a concrete driveway at an open garage

When a trailer is the only safe option

No maker says outright that a jet ski can't ride in a truck. What the sources do give are limits, and when a truck-bed setup can't meet one of them, a trailer is the option left:

  • Weight. The craft with fuel, the carrier and the gear add up to more than your truck's placard leaves after the people aboard. Under the federal load-limit steps, that weight may not safely exceed the available cargo capacity.
  • Support. No carrier maker rates a product for your craft and bed. Sea-Doo's 2026 guide, writing about trailers, says the bunks should be adjusted to support the hull throughout its full length, and TruckBoss says a FlexxLoader with a PWC on a standard or short-bed truck will likely need its Flip Extension to support the full length of the setup.
  • Length. The load would reach farther back than your state allows, as with California's limit of two-thirds of the wheelbase behind the last point of support, or you can't fit the flags and lights your state requires.
  • Position. Sea-Doo's guide, in the same trailer section, says to carry the watercraft in its normal operating position. If a setup would carry it at an angle, ask your dealer whether that is acceptable for your model.
  • Lifting. Getting the craft into the bed would mean lifting it without gear rated for its weight, and the manuals cited here name no lifting points.

Beyond those checks the evidence is thin, so treat the rest as a working assumption. The three manuals cited here describe transport only on a trailer, and this guide found one carrier maker publishing jet ski specs. That suggests, but doesn't prove, that a trailer is the setup the craft makers have in mind. The check that settles it for your craft is to ask your dealer whether the maker approves the truck-bed setup you plan to use. It's worth asking: Yamaha's limited warranty, printed in its 2026 VX manual, lists “damage due to improper transportation” among its general exclusions.

For the trailer route, see how to tow a jet ski, the jet ski trailer buying guide and how much a jet ski weighs with its trailer.

Truck-bed transport checklist

Run this list before you leave and again before the drive home. Each item names who says it, where a source does.

Before and after the drive

Covering a jet ski on the move

Two of the craft makers mention a cover for the road, both in trailer terms. Sea-Doo's 2026 guide says a Sea-Doo cover can protect the watercraft, particularly when driving on dirt roads, to prevent dirt entry through the air inlet openings. Yamaha's 2021 Maintenance Matters guide says to protect a WaveRunner with a Yamaha storage cover when it isn't in use or when trailering.

Our Weatherproof Shield is sold as a trailerable cover. The supplier's spec lists air vents to aid trailering, built-in buckles and straps, an elastic hem cord, a mesh storage bag and an extra strap set, in 600D solution-dyed polyester with a PU coating. The cover is water-resistant. Trailering is the use that spec covers; it says nothing about an open truck bed, so this guide doesn't suggest the cover for one. Its buckles and straps hold the cover on the craft, not the craft on a carrier. The Satin Shield is an indoor cover (Satin storage bag included), not one for the road.

Covers are sized by overall length, bow to stern, and the size guide matches yours to a size. The cover carries a Lifetime warranty. See all our jet ski covers.

Trailerable Cover

AllGuard Weatherproof Shield Jet Ski Cover (Trailerable)

Sold as a trailerable cover: air vents to aid trailering, built-in buckles and straps and an elastic hem cord, in water-resistant 600D solution-dyed polyester with a PU coating.

4 colors: Blue / Black, Gray / Black, Red / Black, Yellow / Black

  • Under 90 inP0
  • Under 102 inP1
  • Under 115 inP2
  • Under 125 inP3
  • Under 135 inP4
  • Under 145 inP5
  • Up to 160 inP6

Lifetime Warranty

Transporting a jet ski without a trailer: FAQ

The craft makers don't say: the transport sections of the 2026 Sea-Doo, Yamaha and Kawasaki manuals cited here are written for trailers, and none mentions a truck or pickup. Carriers for it are sold; TruckBoss, for example, sells a pickup deck with FlexxLoader skids for sit-down and stand-up jet skis. Check the load against your truck's placard and your state's overhang rules, and ask your dealer first.

Measure before you cover it

Our covers are sized by overall length, bow to stern. Measure the craft, then match the number in the size guide.

Open the size guide

Sources

  1. 2026 GTI, GTR and WAKE Series Operator's Guide: Transporting the Watercraft (pp. 35-36); Mooring Cleats, Front Eyelet and grab handle (p. 137) (opens in a new tab)BRP (Sea-Doo) · 2026 edition, read 2026-10-27
  2. 2026 WaveRunner VX-C/VX/VX Deluxe/VX Cruiser/VX Limited Owner's/Operator's Manual, LIT-18626-15-77: Equipment (pp. 64-66), Transporting on a trailer (p. 75), Limited warranty (p. 119) (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2026 edition, read 2026-10-27
  3. JET SKI STX 160LX / STX 160X Owner's Manual, JN1500F/H (2026): General information (pp. 104, 106), Transporting (pp. 145-146) (opens in a new tab)Kawasaki Motors Corp., U.S.A. · 2026 edition, read 2026-10-27
  4. Our Decks (specifications and bed lengths) (opens in a new tab)TruckBoss Decks · read 2026-10-27
  5. FAQs (weight rating, ramp ratings, deck weights, Flip Extension) (opens in a new tab)TruckBoss Decks · read 2026-10-27
  6. FlexxLoader PWC Large: Sit-Down Jet Ski Loading Ramp for Pickup Trucks (SKU 5201) (opens in a new tab)TruckBoss Decks · read 2026-10-27
  7. FlexxLoader XL: Sit-Down Jet Ski Loading Ramp for Pickup Trucks (SKU 5201XL) (opens in a new tab)TruckBoss Decks · read 2026-10-27
  8. FlexxLoader PWC Small: Stand-Up Jet Ski Ramp for Trucks (SKU 5202) (opens in a new tab)TruckBoss Decks · read 2026-10-27
  9. FlexxLoader Buggy System (SKU FLBS25) (opens in a new tab)TruckBoss Decks · read 2026-10-27
  10. Lift Kit, SKU 295100758 (opens in a new tab)BRP (Sea-Doo official store) · Wayback Machine copy of 2024-06-24 (the live page blocks automated reads)
  11. Yamaha Deluxe Lift Harness, MWV-LFTHR-ES-10 (opens in a new tab)Yamaha Motor Corporation, U.S.A. · read 2026-10-27
  12. 49 CFR 571.110, FMVSS No. 110: S2 Application and S4.3 Placard (opens in a new tab)National Highway Traffic Safety Administration (eCFR) · eCFR up to date as of 2026-10-23; read 2026-10-27
  13. 49 CFR 575.6(a)(4)-(5): owner's manual load-limit information and Steps for Determining Correct Load Limit (opens in a new tab)National Highway Traffic Safety Administration (eCFR) · eCFR up to date as of 2026-10-23; read 2026-10-27
  14. SuperJet: specifications (opens in a new tab)Yamaha Motor Corporation, U.S.A. · read 2026-10-27
  15. 2027 Sea-Doo Spark: specifications (opens in a new tab)BRP (Sea-Doo) · read 2026-10-27
  16. 2027 Sea-Doo GTI: specifications (opens in a new tab)BRP (Sea-Doo) · read 2026-10-27
  17. 2026 Jet Ski Ultra 310LX: specifications (opens in a new tab)Kawasaki Motors Corp., U.S.A. · read 2026-10-27
  18. Transportation Energy Data Book, Edition 41: Table B.9 (gasoline weight) (opens in a new tab)Oak Ridge National Laboratory, US Department of Energy · 2025; read 2026-10-27
  19. California Vehicle Code section 24604 (opens in a new tab)California Legislative Information · amended by Stats. 2015, ch. 451, effective 2016-01-01; read 2026-10-27
  20. California Vehicle Code section 35410 (opens in a new tab)California Legislative Information · enacted by Stats. 1959, ch. 3; read 2026-10-27
  21. Florida Statutes 316.228, Lamps or flags on projecting load (opens in a new tab)The Florida Senate · 2025 Florida Statutes; read 2026-10-27
  22. Florida Statutes 316.520, Loads on vehicles (opens in a new tab)The Florida Senate · 2025 Florida Statutes (history to ch. 2020-135); read 2026-10-27
  23. 625 ILCS 5/12-204, Lamp or flag on projecting load (opens in a new tab)Illinois General Assembly · Source: P.A. 77-37; read 2026-10-27
  24. Code of Virginia 46.2-1121, Flag or light at end of load (opens in a new tab)Virginia Legislative Information System · history to 2022, c. 50; read 2026-10-27
  25. RCW 46.37.140, Lamps and flags on projecting load (opens in a new tab)Washington State Legislature · history to 2014 c 154; read 2026-10-27
  26. RCW 46.61.655, Dropping load, other materials: Covering (opens in a new tab)Washington State Legislature · history to 2005 c 431; read 2026-10-27
  27. Owner's Manual & Safety Instructions, item 60397 (loading ramps) (opens in a new tab)Harbor Freight Tools · copyright 2022; read 2026-10-27
  28. Maintenance Matters: A Simple Guide for the Longevity of Your WaveRunner (2021) (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2021; read 2026-10-27
  29. Personal Watercraft (PWC) Dolly, part 27575 (opens in a new tab)C.E. Smith Company · read 2026-10-27

Find Your Size

Measure your jet ski bow to stern in a straight line, then enter the length in inches.

  1. Under 90 inP0
  2. Under 102 inP1
  3. Under 115 inP2
  4. Under 125 inP3
  5. Under 135 inP4
  6. Under 145 inP5
  7. Up to 160 inP6
Full Size Guide

In inches. Decimals are fine.

Covers for Your Jet Ski

All Covers