AllGuard Weatherproof Shield
Outdoor storage and trailering
$139.99
Lifetime WarrantyStorage
Off the trailer, a jet ski still needs something under its hull. Here is what the support makers and Sea-Doo, Yamaha and Kawasaki publish, and where they say nothing.
A jet ski without a trailer still needs something solid under its hull. In a garage, a shed or a storage space that can mean a dolly, a stand or a rack, and getting the craft onto one raises a question the owner's manuals answer only in the negative: which parts you must never lift it by.
This guide sticks to what the makers publish. The support makers' own product pages give the capacities, bunk spacing and uses below. Sea-Doo, Yamaha and Kawasaki's 2026 manuals list parts you must never lift the craft by. Where neither says anything, the guide says so and points you to your owner's manual or dealer. For the bigger picture of where to keep a craft, start with jet ski storage.
Note
Examples, not recommendations
Products named here are examples from their makers' own pages, read on 2026-10-27 (the Sea-Doo Lift Kit from a June 2024 archived copy), not a ranking or an endorsement. Capacities and features are the makers' figures. Your owner's manual and your dealer have the last word on how your craft should be supported and stored.
Off the trailer, the craft needs support under its hull. The makers' pages below describe two kinds of frame: dollies, which put bunks on casters so the craft can be rolled, and stands, which hold the bunks at a set height for display, service or storage. Blocks or cribbing do without a frame. Here are examples of both frames from the makers' own pages.
| Support (maker's page) | What the maker says it's for | Bunks | Stated capacity |
|---|---|---|---|
| C.E. Smith PWC Dolly (27575) | Moving a jet ski or other small vessel on any hard surface, and into a storage space | Two 4 ft carpeted bunks, set 12, 16 or 20 in apart | 1,000 lb |
| AquaCart AQ-19 cart and service stand | Display, service and storage | 48 in carpeted bunks, 14 to 20 in apart, 19 in bunk height | PWC up to 1,300 lb; 1,800 lb with optional 6 in casters |
| AquaCart AQ-11 low-profile stand | Showroom display; 11.5 in tall | 48 in bunks: 20 in apart for most sit-down craft, 14 in for deep-V hulls, 12 in for newer stand-ups | PWC up to 1,300 lb; 1,800 lb with optional 6 in casters |
| Extreme Max 3005.5592 stand-up PWC dolly | Off-season storage and maintenance of a stand-up PWC | Adjustable-width bunks, 19 in high | 1,300 lb |
| Blocks or cribbing | No blocking plan in the Sea-Doo, Yamaha or Kawasaki manuals cited here | None published | None published |
A dolly suits a craft that has to move. C.E. Smith describes its PWC dolly as a way to move a small vessel such as a jet ski around on any hard surface and into a storage space. Once it's parked, casters that lock keep it there: Extreme Max says two of its stand-up dolly's casters lock in place for stable storage or maintenance work, and AquaCart offers caster brakes on the AQ-19 to restrict unwanted movement.
Height matters for the hand-off from the trailer. AquaCart calls the AQ-19's 19-inch bunk height great for trailers, and Extreme Max says its 19-inch dolly is designed to align with most low-slung PWC trailers, so the craft can move between trailer and dolly. For moving the craft once the trailer is gone, see how to transport a jet ski without a trailer, and for fitting a craft and its support into the space, storing a jet ski in a garage.
Electric or powered PWC dollies come up in searches too, but no maker page with published specs for one was found for this guide, so none is compared here. The checks below, capacity and bunk spacing, would apply to one the same way.

A stand holds the craft at a working height. AquaCart sells the AQ-19 as a showroom cart and service stand, for display, service and storage, while its AQ-11 is a low-profile showroom stand 11.5 inches tall. Both roll on four-way swivel casters.

All three makers let you set the bunks to the hull. C.E. Smith says its bunks adjust to gently support the vessel. Extreme Max says to set the bunk spacing to the width of your stand-up hull for a stable, secure fit. AquaCart builds the AQ-11 in three bunk widths: 20 inches for most sit-down craft, 14 for deep-V hulls and 12 for newer stand-ups such as the SuperJet and SX-R. Kawasaki's 2026 STX 160 manual sets a similar test for trailers: be sure the trailer matches the craft's weight and hull design.
A support's rating has to cover the craft as it will sit, not just its dry weight. Kawasaki lists the 2026 Ultra 310LX at an estimated 996.7 lb dry and 1,137.8 lb curb, and says the curb figure includes all necessary materials and fluids to operate correctly, a full tank of fuel (more than 90 percent capacity) and the tool kit, if supplied. That curb weight is 137.8 lb more than a 1,000 lb rating (1,137.8 minus 1,000), and 162.2 lb under a 1,300 lb one (1,300 minus 1,137.8). Fuel is part of the stored weight if your manual has you store the craft with a full tank, as Yamaha's 2026 owner's manuals do (its 2021 Maintenance Matters guide says 7/8 full). How much does a jet ski weigh? lists dry and curb weights by model.
Getting the craft off its trailer and onto a support is where lifting comes in. None of the three 2026 manuals cited here names a point to lift the whole craft from. They do name parts you must not lift it by, and Yamaha's and Kawasaki's warnings say the craft could fall and cause severe injury.
| Maker and manual | Part | What the manual says |
|---|---|---|
| Sea-Doo, 2026 GTI, GTR and Wake guide | Mooring cleats | Can be used for docking. Never use them to pull or lift the watercraft |
| Sea-Doo, same guide | Front eyelet | Eyelets can be used for mooring, towing and as tie-down points when trailering. Do not use these eyelets to lift the watercraft |
| Sea-Doo, same guide | Molded grab handle | A handhold. Never use it to tow anything or to lift the watercraft |
| Yamaha, 2026 VX manual | Cleat | For a ski rope. Do not use it to lift the watercraft; it is not designed to support the craft's weight |
| Yamaha, same manual | Handgrip, reboarding step, pull-up cleats | Not designed to support the craft's weight; do not use them to lift it |
| Kawasaki, 2026 STX 160LX/160X manual | Handrail | Do not lift the watercraft using the handrail (repeated on an on-craft warning label) |
| Kawasaki, same manual | Multi-mount system | Do not lift the watercraft using it |
The bow and stern eyes are where the manuals point ropes and tie-downs. Describing its front eyelet, Sea-Doo's guide says eyelets can be used for mooring, towing and as tie-down points when trailering. Yamaha's bow eye attaches a rope when transporting, mooring or towing in an emergency, and its stern eyes when transporting or mooring. Kawasaki says to use only the bow and stern eyes when fastening the craft to a trailer. None of the three calls them lifting points, and Sea-Doo warns not to use these eyelets to lift the craft. Their trailer use is covered in how to tie down a jet ski on a trailer.
If the plan is to hoist the craft with a sling, the owner's manuals don't help. A text search of the 2026 Sea-Doo GTI, GTR and Wake guide, the 2026 Yamaha VX manual and the 2026 Kawasaki STX 160 manual finds no instructions for lifting the whole craft with a sling, hoist or crane, and none of them gives lifting points.
Two of the makers' stores have listed lifting gear:
Neither product page's text says where the gear attaches to the hull or how to rig it, and this guide doesn't either.
Important
No lifting instructions here
This guide gives no sling or hoist rigging advice. Sea-Doo, Yamaha and Kawasaki name parts that must not be used to lift the craft, but none of the manuals cited here says where a sling attaches. If the craft has to be lifted, follow the lifting gear maker's instructions and ask your dealer.
Discover Boating describes dry stack storage as a covered facility, sometimes called a boatel, where boats sit on huge racks inside a building and staff fork-lift them off the racks and into the water; to go out before or after business hours, you may need to call ahead. BoatUS's 2021 winterizing guide adds that dry storage racks are designed for typical boat hulls but can't always be adjusted to support unusual designs. If you doubt the support a rack gives, BoatUS suggests consulting a marine surveyor or considering another winter spot, such as a trailer, and it says to check with the yard about its fuel-tank requirements, which are there to prevent fires, whether the rack is indoors or outside.
A lift at the dock is another way to keep the hull up without a trailer; jet ski lifts and docks covers lift types and ratings.
A home rack that holds the craft on bunks raises the same questions as a stand: the maker's stated capacity against the craft's weight with fuel, and bunks set for your hull.
Racks that tilt the craft or stand it on end are a different case. All nine of Yamaha's 2026 U.S. owner's manuals carry the same warning: “Always place the watercraft upright in a horizontal position when storing it, otherwise fuel could leak out into the engine or engine compartment, which could create a fire hazard.” Under “Tilting the Watercraft,” Kawasaki's 2026 STX 160 manual says tilting the craft onto its starboard side can let water in the exhaust system run into the engine, and to always tilt it onto its port side if it is necessary to inspect the bottom. The storage section of Sea-Doo's 2026 GTI, GTR and Wake guide gives no storage position. Before you consider any rack that tilts or upends the craft, read the storage section of your own manual and ask your dealer.
This guide gives no construction plans, dimensions or load figures for a homemade stand or rack. None of the Sea-Doo, Yamaha or Kawasaki manuals cited here publishes them, and a homemade support comes with no maker's rating.
What a published source does offer is general principles for hulls stored ashore. BoatUS's 2021 winterizing guide, written for boats in general rather than jet skis, says:
For a jet ski, ask your dealer how your hull should be supported before you build or block anything.

The storage prep itself, from flushing and fuel to the battery and engine protection, is in how to winterize a jet ski, with make-specific steps for a Sea-Doo, a Yamaha WaveRunner and a Kawasaki. Some of those steps raise one end of the craft to drain it, not to store it that way: Sea-Doo's 2026 guide has you lift the front end to drain the bilge completely through the drain plugs, and Kawasaki's 2026 STX 160 manual has you lift the stern a little so the fuel tank can be drained completely. Plan them with your support in mind, and follow your manual for how.
Then cover it. Kawasaki's 2026 STX 160 manual's storage steps include “Cover the watercraft and store it in a clean, dry place.” For a craft kept indoors on a stand or dolly, the Satin Shield is our indoor cover: 85% polyester and 15% spandex stretch fabric with a sheared fleece interior and elastic front and rear hems. It comes in two sizes, for craft up to 117 in and up to 138 in long, so measure the overall length first with the size guide. If the craft has to sit outside, the Weatherproof Shield is the outdoor cover, made of water-resistant 600D solution-dyed polyester with a PU coating. Both carry a Lifetime warranty, and the full range is in our jet ski covers.
Indoor Cover
AllGuard Satin Shield Indoor Jet Ski Cover
For a craft kept indoors on a stand or dolly: a stretch cover with a sheared fleece interior and elastic front and rear hems. Two sizes, for craft up to 117 in and up to 138 in long.
Color: Black
$129.99
Shop the Satin ShieldYes. Dolly and stand makers sell supports for it: C.E. Smith describes its PWC dolly as a way to move a jet ski into a storage space, and AquaCart sells its AQ-19 stand for display, service and storage. Check the support's stated capacity against the craft's weight with fuel, set the bunks for your hull, and store the craft in the position your owner's manual gives.
Not according to the manuals cited here. Sea-Doo's 2026 guide says never to use the mooring cleats to pull or lift the watercraft and, under its front eyelet, not to use these eyelets to lift it. Yamaha's 2026 VX manual says not to lift by the cleat, which isn't designed to support the craft's weight, and Kawasaki's 2026 STX 160 manual says not to lift by the handrail.
The 2026 Sea-Doo, Yamaha and Kawasaki manuals cited here don't say: none describes lifting the whole craft with a sling or names lifting points. BRP's store has listed a Sea-Doo Lift Kit (archived June 2024) and Yamaha's sells a Deluxe Lift Harness, but neither product page's text says how they attach. Follow the gear maker's instructions and ask your dealer.
Check your owner's manual first. All nine of Yamaha's 2026 U.S. manuals say to always store the watercraft upright in a horizontal position, warning that fuel could otherwise leak into the engine or engine compartment and create a fire hazard. Kawasaki's 2026 STX 160 manual says tilting the craft onto its starboard side can let exhaust water run into the engine.
More than your craft weighs as it will be stored. The makers' ratings in this guide are 1,000 lb (C.E. Smith), 1,300 lb (Extreme Max 3005.5592) and, for AquaCart's AQ-19 and AQ-11, PWC up to 1,300 lb, or 1,800 lb with optional 6-inch casters. Kawasaki lists the 2026 Ultra 310LX at a curb weight of 1,137.8 lb, which includes a full tank of fuel (more than 90 percent capacity); that is more than 1,000 lb. Our weight guide lists other models.
This guide gives no plans or load figures, and none of the PWC manuals cited here publishes them. BoatUS's 2021 general advice for boats stored ashore is to get a blocking plan from the manufacturer if one exists, not to use a cradle built for a different model, and to check after blocking that the stands aren't depressing the hull. Ask your dealer what your hull needs.
Kawasaki's 2026 STX 160 manual's storage steps include “Cover the watercraft and store it in a clean, dry place.” For indoor storage, the Satin Shield is our stretch cover, in two sizes for craft up to 117 in and up to 138 in long; size it by the craft's overall length.
Our covers are sized by overall length, bow to stern. Measure the craft, then match the number in the size guide.
Measure your jet ski bow to stern in a straight line, then enter the length in inches.