AllGuard Weatherproof Shield
Outdoor storage and trailering
$139.99
Lifetime WarrantyStorage
A lift or drive-on dock keeps a jet ski out of the water between rides. How to pick one for your water, cover the craft on it, and dock, beach and winter it safely.
A lift holds the hull out of the water between rides, and that matters to the manufacturers. Yamaha's 2026 owner's manuals say to take the watercraft out of the water after use, because extended periods in the water speed up wear on the jet pump and hull. Kawasaki's 2022 STX 160 manual says its craft aren't designed to be docked in the water for extended periods. A drive-on floating dock does the same job without any lifting. Tied alongside a dock, the craft is still floating, which is fine for a stop and not for storage.
This guide covers keeping and covering a jet ski on a lift, on a drive-on dock, at a slip or in a boathouse; choosing and siting the equipment; and docking, tying up, beaching and anchoring when you're out riding. For every other place a jet ski can live, start with the jet ski storage guide.
Note
Specs come from the makers
Capacities and dimensions in this guide are quoted from each lift or dock maker's own pages, retrieved in October 2026, and craft weights from Sea-Doo, Yamaha and Kawasaki. Models change, so check the current spec sheet and your owner's manual before you buy or install anything.
On a lift, yes. Discover Boating says keeping a boat out of the water when it's not in use can help protect it from wakes, storms, corrosion, marine growth and hull damage, and a lift does that between rides. BoatUS calls lift storage the best of both worlds: most of the advantages of storage ashore, with the boat ready to use when the weather is good. Discover Boating adds that slip holders with a lift may keep the boat on it through the winter.
A lift still has limits, and BoatUS's claim files show where they are:
A drive-on floating dock, sold as a port or a floating PWC lift, also keeps the craft out of the water: EZ Dock describes its ports as a way to store a jet ski out of the water, and Jet Dock calls its system a way of parking one out of the water. Tied alongside a dock with no lift or port, the craft is floating. Kawasaki says to remove the craft from the water at the end of each day's use and not to leave it in overnight, because prolonged immersion makes hull paint bubble and peel and causes electrolytic erosion of some metal parts in the jet pump. The full answer is in can you leave a jet ski in the water?
A craft on a lift sits outdoors, in the same sun, rain and wind as one parked outside on a trailer. BoatUS says a cover is even more important for a boat stored on a lift.
For a ski kept outdoors, on its trailer or on a lift or drive-on port, use an outdoor cover such as our Weatherproof Shield: water-resistant 600D solution-dyed polyester with a PU coating, an elastic hem cord, built-in buckles and straps, and air vents. It comes in seven sizes by overall length, and the size guide matches your measurement to a size.
Trailerable Cover
AllGuard Weatherproof Shield Jet Ski Cover (Trailerable)
An outdoor cover for a ski kept outside, on its trailer or on a lift: water-resistant 600D PU-coated polyester, elastic hem cord, built-in straps and buckles. Seven sizes by overall length.
4 colors: Blue / Black, Gray / Black, Red / Black, Yellow / Black
$139.99
Shop the Weatherproof ShieldThey do different jobs. A canopy is a fabric roof on a frame above the lift. Hewitt sells its PWC lift canopy for protection from sun, rain and debris, and ShoreMaster's canopy covers have vented ends that let air through to reduce wind uplift. A cover goes on the craft itself, closes around it down to the hem where a canopy leaves the sides open, and travels with it from the lift to the trailer to the garage.
The sources pull different ways. ShoreMaster, which sells canopies, argues in an article about boats that a canopy is a better fit for a boat lift than a boat cover. BoatUS says a cover is even more important on a lift. Neither addresses a jet ski under both, and the two don't conflict: the canopy shades the craft from above, and the cover helps keep wind-blown rain and debris off the seat and deck.
If you add a canopy, follow the makers' rules for it:

The water decides more than the brochure does. Sunstream lists the considerations: water depth, how much the level fluctuates, how much wave activity there is, how portable the setup needs to be, and local restrictions. ShoreMaster says the best choice depends on water depth, dock type, and how often you launch and store the craft.
| Freestanding lift | Drive-on floating port | |
|---|---|---|
| How it holds the craft | On bunks, raised by a crank or a motor | On rollers or wheels; you drive up onto it |
| Bottom | Firm or semi-soft, on adjustable legs (ShoreMaster) | Floats; needs an anchor point (Jet Dock) |
| Changing water level | Vertical lifts suit it; cantilever lifts suit steady shallow water (ShoreMaster) | Moves with the water level (EZ Dock) |
| Water depth | Varies by model; ShoreStation rates its vertical PWC lift to 5 ft 6 in | Enough for the craft's draft on approach (Jet Dock) |
| Waves and storms | Strap the craft down; lifts fare badly in big storms (BoatUS) | Fast, simple operation, especially in calm conditions (ShoreMaster) |
| Effort | Hand crank (Hewitt), or a motor on a 12V deep-cycle battery (ShoreMaster) | No winching, cranking or hoisting (EZ Dock) |
Tides and big level swings favor floating equipment. ShoreMaster, which sells HydroHoist floating lifts, says on its floating-lift page that floating lifts are the best choice for deep lakes, rivers with changing water levels, or saltwater marinas, and that if your dock rises and falls with the water, a floating lift moves with it. Jet Dock says its drive-on docks work in shallow, deep and tide-affected water with proper hardware and installation. A bottom-standing lift has to keep the depth within its range all season, and in cold climates Discover Boating says bottom-standing lifts typically come out of the water for winter.
Here are the main types, each with an example rating from a maker's own spec page.
| Type | How it works | Suits | Example rating |
|---|---|---|---|
| Vertical | The cradle rises straight up inside a frame on legs | Changing water depth (ShoreMaster) | ShoreStation vertical PWC lift: 1,500 lb |
| Cantilever | Arms pivot to swing the cradle up | Steady, shallow water (ShoreMaster) | Hewitt single cantilever PWC lift: up to 1,150 lb |
| Swivel or davit | Mounted on a seawall or piling; swings the craft over the pier or dock | Seawalls and pilings (Magnum, Golden) | Magnum RotoMag: 1,500 lb |
| Floating lift | Floats beside the dock and rises and falls with it | Deep lakes and rivers with changing levels (ShoreMaster) | HydroHoist (ShoreMaster) range: 4,400 to 32,000 lb |
| Drive-on port | A floating platform with rollers; you drive on | Calm water and changing levels | EZ Dock EZ Port 2i: up to 1,700 lb |
Within each type the details vary. ShoreMaster rates all three of its PWC lifts at 1,200 lb. FLOE's PWC lifts handle craft up to 1,600 lb, and Golden Boat Lifts says its PWC lifts raise up to 1,500 lb depending on the model, including a seawall- or piling-mounted model that swivels 180 degrees. Magnum says no part of its RotoMag stays in the water. Lifts are cranked by hand or motorized: ShoreMaster's motorized systems run on a standard 12V marine deep-cycle battery, with solar kits available to keep it charged. Double lifts for two craft exist too: Hewitt's double cantilever lift is rated 1,200 or 1,800 lb in total, and FLOE's V-2602 holds two PWCs at adjustable, staggered heights.
Size a lift by what it will really carry, not the brochure's dry weight. Sunstream says to start from the dry weight and add the engine, fuel, water and any equipment, then choose a model that carries that fully loaded weight; it also warns that published boat specifications are often inaccurate. ShoreMaster says a drive-on port should support the craft's full weight, including fuel and gear, and leave extra capacity in case you move to a larger or heavier craft. ShoreMaster also says fit depends on the craft's length, weight and hull shape, so it advises choosing both the right capacity and the right bunk configuration.
Kawasaki lists the 2027 Ultra 160LX at an estimated 888.6 lb dry weight and 1,029.7 lb curb weight, and says curb weight includes the fluids the craft needs to run and a fuel tank more than 90 percent full. Gear and any water in the hull come on top of that, and BoatUS warns that rain and snow collecting in a boat can push it past a lift's safe working load.
| Model (maker's spec page) | Dry weight | Overall length |
|---|---|---|
| Sea-Doo Spark (2027) | 437 to 441 lb | 111 in (2-up) |
| Yamaha VX (2027) | 719 lb | 132 in |
| Sea-Doo GTI (2027) | 741 lb | 130.7 in |
| Kawasaki STX 160X (2027) | 798.2 lb | 130.3 in |
| Sea-Doo GTX Limited (2027) | 849 lb | 135.8 in |
| Kawasaki Ultra 160LX (2027) | 888.6 lb | 140.9 in |
| Yamaha FX HO (2027) | 908 lb | 139 in |
For more models, see how much does a jet ski weigh?
Tip
Check the lift warranty for your water
Some PWC lift warranties cover fresh-water use only: Hewitt's says so, and so does Sunstream's for its Dock Jock PWC lifts. If the lift will sit in salt or brackish water, read the warranty before you buy. BoatUS also says rinsing a lift with fresh water after every use goes a long way toward preventing corrosion.
Size a drive-on port the way you size a cover: by the craft's measured overall length first, then its loaded weight. Measure bow to stern as described in how to measure a jet ski for a cover, then compare the number with the port's length and the maker's fit list. ShoreMaster says to confirm the craft's weight, dimensions and installation requirements before choosing a port. The makers publish their numbers:
| Port (maker) | Length | Width | Rated load |
|---|---|---|---|
| ShorePort (ShoreMaster) | 138 in | 58 in | 1,150 lb; 1,450 lb with extra flotation |
| HydroPort Epic (ShoreMaster) | 162 in | 70 in | up to 2,000 lb |
| EZ Port 2i (EZ Dock) | 168 in | 58.5 in | up to 1,700 lb |
| EZ Port 260 (EZ Dock) | 156 in | 60 in | not listed on its page |
| Pro Wide Body (Wave Armor) | 150 in | 80 in | 2,250 lb |
| Connect-A-Port XL5 (Connect-A-Dock) | 156 in | 59 in | 1,800 lb maximum flotation |
| Connect-A-Port XL6 (Connect-A-Dock) | 156 in | 72 in | 2,000 lb maximum flotation |
| JetSlide (Candock) | 10 ft | not listed | 1,500 lb |
How the hull meets the port matters too. ShoreMaster's ShorePort carries the craft on three adjustable polyurethane rollers. Connect-A-Dock's wheels adjust to match the hull, and it says its port material is smooth and non-abrasive, reducing the risk of scratching, scuffing or gouging as the craft rolls on and off. Wave Armor's Pro 6 port uses 12 wheels of varied softness and diameter, positioned for hull protection. EZ Dock's EZ Port 260 uses split-entry rollers, and its ports have a raised bow that helps keep riders from overshooting.
To keep hull wear down:

Check the site before you order anything. Most of this list comes from the makers' own selection advice.
Permits are local, and there can be several layers. Sunstream says permitting requirements vary with local restrictions and regulations, and tells owners to contact their local permitting agency. On navigable US waters, the federal layer is the US Army Corps of Engineers: Section 10 of the Rivers and Harbors Act of 1899 requires its authorization for any structure in or over navigable water, and the Corps' Los Angeles District says that applies to all structures, from the smallest floating dock up. In a 2012 release, the Corps' Pittsburgh District reminded boaters that personal docks on navigable rivers need federal and/or state permits, and said the rules may differ by state.
Below that sit the state natural-resources or environmental agency, the town or county, and the marina or homeowner association. Discover Boating says local regulations and homeowner or marina policies may also affect which types of lifts you can install, and Jet Dock tells marina customers to check with the harbormaster. The rules differ: Minnesota's DNR, for example, says no state permit is needed for a dock on shoreline you own if it meets set conditions, one of which is following local government guidelines. Ask before you buy, not after the lift is in.
A jet ski docks differently from a boat. Discover Boating explains why: with no rudder, it relies on thrust from the jet pump to steer, so momentum, wind and current quickly influence its course as soon as you let off the throttle. Sea-Doo's 2026 operator's guide says directional control is reduced when the throttle is released and lost when the engine is off, and recommends practicing with an imaginary dock first.
Yamaha's 2026 VX manual says to release the throttle about 70 m (230 ft) from the dock. Kawasaki says never to approach any object closer than 100 m (328 ft) at high speed, and to throttle down before the stopping area.
Discover Boating says to approach into wind or current where possible, at idle, with short blips of throttle for steering and an escape route in mind. Some craft have no reverse, so watch your speed.
Yamaha's 2026 VX manual has the VX-C stop its engine just before coming alongside, warning that you need throttle to steer; on models with the RiDE lever, it says to approach slowly using the throttle and RiDE lever and stop the engine after coming alongside. On a Sea-Doo, BRP says to maneuver with the iBR lever and throttle, and reminds riders that steering is reversed when backing up.
Discover Boating says to tell passengers to sit tight and not to reach out with a leg or arm to stop the craft.
Use the mooring points your owner's manual names. Sea-Doo's guide says its mooring cleats can be used for docking and its front eyelet for mooring, and never to use the cleats to pull or lift the craft or the eyelets to lift it; Yamaha's manual names the bow eye and stern eyes. Discover Boating says a second line at the stern stops the craft swinging out from the dock.
Hang fenders at the widest part of the hull, and at a floating dock just above the waterline. Leave lines snug but not tight so they absorb waves and wakes, and in tidal water long enough for the craft to rise and fall.

The knot. Discover Boating says the cleat hitch is the only knot you need for a dock cleat, and that it must finish with a locking half-hitch or it will slip. It names nylon as the most popular dock-line material, for its strength and stretch, and says to check lines regularly for chafe and wear.
Leaving it tied up. Treat a tie-up as a stop between rides. BoatUS says chafe can happen even in fair weather in a well-protected slip, because water, wind and tide keep a boat in constant motion. Many of its wake claims come from boats slammed into their own docks by passing wakes, and it says extra fenders and proper dock lines can often prevent that hull damage. At the end of the day, take the craft out of the water, as Kawasaki and Yamaha direct.
All three manufacturers want the engine off before the water gets shallow, because a jet pump draws in whatever is on the bottom. They draw the line at different depths:
| Sea-Doo (2026 GTI guide) | Yamaha (2026 VX manual) | Kawasaki (2022 STX 160 manual) | |
|---|---|---|---|
| Running onto the beach | Not recommended | Stop the engine just before land (VX-C) or once on land (RiDE models), then pull it up | Avoid beaching |
| Engine off before the water is shallower than | 3 ft (90 cm) under the lowest rear part of the hull | 2 ft (60 cm) under the bottom of the craft | 2.6 ft (0.8 m) |
| The risk named | Damage to the impeller, iBR and jet pump | Sand or pebbles in the intake: impeller damage and overheating | Stones and sand scratch the hull and reach the impeller |
Discover Boating says it can be safer to beach anchor: keep the craft in shallow water off the sand rather than on it. It adds that sand in a jet drive can wreak havoc with the engine, and to think about the tide: if it goes out, can you get the craft back in the water, and if it comes in, will it float away? The BoatUS Foundation says to keep a PWC out of water less than two feet deep and away from sea grass and other vegetation, to avoid docking or beaching among reeds, grasses or mangroves, and not to anchor near coral.
Anchoring. The BoatUS Foundation suggests carrying an anchor and extra line on a jet ski. Discover Boating says small mushroom anchors have minimal holding power and should be used only for personal watercraft, small aluminum fishing boats or dinghies. For boats in general, the BoatUS Foundation recommends a scope of 7:1, seven feet of line for every foot of water depth, or 5:1 for a light anchor on a small boat in good weather. Lower the anchor rather than throwing it, and allow for the craft swinging a full circle around it as the wind or current shifts. Sea-Doo's guide makes the owner responsible for anchor lines and anchors being adequate for the craft's use.
Winterize the craft itself first: the engine procedure is in how to winterize a jet ski, and where to keep it through the cold months is in jet ski winter storage. Then decide whether the craft, and the equipment, stay on the water.
The craft. For boats left on a dock lift over winter, BoatUS's checklist says to check the lift's wires, chains and fittings, install dock lines to keep the boat in the slip should the lift drop, secure the boat to the lift against high winds, and strongly consider removing it and storing it ashore. Its winterizing guide says that where strong winter storms hit, or the lift is exposed to fetch from the direction of the prevailing storm winds, the trailer is the better place. A BoatUS claim shows why snow matters: a boat left on its lift through a Midwestern winter filled with snow until the combined weight far exceeded the lift's safe working load, and the lift collapsed.
The equipment. Here the makers disagree, so follow the instructions for your own model:
| Maker | Equipment | Winter guidance |
|---|---|---|
| ShoreMaster | Lifts | Can stay on the water over the off-season with motors covered and power disconnected, citing Brinson Marine Waterfront Manager Chris Jacobs; check for ice, especially after significant snowfall or temperature drops |
| ShoreMaster | ShorePort floating dock | Remove it to prevent ice damage |
| Sunstream | FloatLift | If the boat is off the lift for the off-season, best practice is to take the lift out of the water too |
| FLOE | Lifts | Store on level ground away from any ice movement |
| Jet Dock | Floating docks and PWC lifts | Can usually stay in, even where the water ices up; where ice flows, consider taking it ashore |
| Connect-A-Dock | Connect-A-Port | Remove where water freezes; store flat, wheel side up |
| Discover Boating | Bottom-standing lifts | In cold climates, typically removed for winter |
Jet Dock itself adds that removing and winterizing equipment is typically the best option if you won't use it once cold weather arrives, and ShoreMaster says floating docks can stay in over winter if conditions are mild and there is little or no ice movement. Where a craft stays in a slip, Discover Boating warns that if a marina loses power and its agitator stops, a hull can freeze in place and suffer ice damage. Before winter fully sets in, ShoreMaster suggests a marine-grade lubricant on all of a lift's moving parts, and through the winter it says to check a PWC lift for ice, especially after significant snowfall or temperature drops.
Measure overall length, bow to stern, then match it in the size guide. The Weatherproof Shield comes in seven sizes.
Yes. A lift keeps the hull out of the water, which is what Yamaha and Kawasaki ask for after a day's riding. BoatUS calls lift storage the best of both worlds, but says lifts fare badly in hurricanes and strong nor'easters. Strap the craft down, keep it covered and inspect the lift's cables.
Yes. BoatUS says a cover is even more important for a boat stored on a lift. Use an outdoor, water-resistant cover such as the Weatherproof Shield, and clear pooling water after rain or snow.
It depends on the water. Drive-on floating docks move with changing water levels and need no cranking, but ShoreMaster says they offer fast, simple operation, especially in calm conditions. Freestanding lifts need a firm or semi-soft bottom and a depth within their range; vertical lifts suit changing depths, cantilever lifts steady shallow water.
More than the craft's loaded weight. Kawasaki lists the 2027 Ultra 160LX at an estimated 888.6 lb dry and 1,029.7 lb with fluids and a nearly full tank. Sunstream says to size a lift to the fully loaded weight, and BoatUS says to allow for rain and snow collecting in the boat.
Makers design the contact points to limit it: adjustable polyurethane rollers on ShoreMaster's ShorePort, wheels of varied softness on Wave Armor's Pro 6 port, and a non-abrasive surface on Connect-A-Dock's ports. Set the rollers to your hull, rinse sand and grit off them, approach slowly, and check the underside of the hull regularly.
Often. Rules are local: Sunstream tells owners to contact their local permitting agency. On navigable US waters, the Army Corps of Engineers requires authorization for any structure, down to the smallest floating dock, and states, towns, marinas and homeowner associations can add their own rules.
Use the mooring points in your owner's manual, such as the bow eye and stern eyes or mooring cleats, with a bow line and a second line at the stern so the craft can't swing out. Finish each line on the dock cleat with a cleat hitch, hang fenders at the widest part of the hull, and leave a little slack for waves and tide.
Some can. ShoreMaster, citing Brinson Marine Waterfront Manager Chris Jacobs, says its lifts can stay in over the off-season with motors covered and power disconnected, and to check them for ice, especially after significant snowfall or temperature drops. Sunstream says to take its floating lift out when the boat is off it for the off-season, and Discover Boating says bottom-standing lifts in cold climates typically come out. Follow your lift maker's instructions for your ice conditions.
Measure your jet ski bow to stern in a straight line, then enter the length in inches.