Storage

Can You Leave a Jet Ski in the Water?

Not for long. Kawasaki, Sea-Doo and Yamaha say to take it out of the water every day or after each use. What their manuals say, what floating at a dock risks, salt vs fresh water, and the out-of-water options.

By Alex Quinn 13 min read

Generic white personal watercraft floating beside a weathered wooden lake dock at dusk, tied with two lines and fenders, mist on the water

Not for long, according to the companies that build them. Kawasaki's 2026 STX 160 owner's manual says to take the craft out of the water at the end of each day's use and not to leave it in overnight. Yamaha's 2026 VX manual says to take it out of the water after using it. Sea-Doo's 2026 operator's guide says to remove it from the water every day and never to leave it in the water for storage.

So once the riding is done, the makers want the hull out of the water. That can mean a lift, a drive-on floating dock or the trailer. Below is what each manual says and why, what floating at a dock does to a jet ski, how salt and fresh water differ, what the sources say about how long, and the out-of-water options. For every other place a jet ski can live, start with the jet ski storage guide.

Overnight: what Kawasaki, Yamaha and Sea-Doo say

Kawasaki is the most specific. A notice in the end-of-day checklist of its 2026 STX 160LX and STX 160X owner's manual says Jet Ski watercraft are not designed to be docked in the water for extended periods, and that prolonged immersion will cause the hull paint to bubble and peel, as well as electrolytic erosion of some metal parts in the jet pump. To prevent this, it says, remove the craft from the water at the end of each day's use and do not leave it in the water overnight. The manual repeats the notice in its storage chapter.

Yamaha's 2026 VX owner's manual puts this in the post-operation care section that opens its care and storage chapter: after using the watercraft, always take it out of the water, clean it and store it. Leaving it in the water for extended periods will accelerate the rate of normal deterioration of the jet pump and hull, the manual says, and marine organisms and corrosion are among the conditions that can shorten the life of many watercraft components.

Sea-Doo's 2026 operator's guide for the GTI, GTR and Wake series starts its watercraft care chapter with one line: remove the watercraft from the water every day. A notice on the next page adds that the watercraft should never be left in water for storage. Sea-Doo's 2026 GTX Series guide uses the same wording.

Of the three makers' 2026 manuals cited here, only Kawasaki's uses the word overnight. Yamaha's says after using the craft, and Sea-Doo's says every day.

Wording from each maker's 2026 owner's or operator's guide, read October 2026. Follow the manual for your own model.
Maker (manual)What it saysReason it gives
Kawasaki (2026 STX 160LX/160X owner's manual, pp. 142, 147)Remove the craft from the water at the end of each day's use; do not leave it in overnightHull paint bubbles and peels; electrolytic erosion of some metal parts in the jet pump
Yamaha (2026 VX owner's manual, p. 100)After using the watercraft, always take it out of the waterFaster deterioration of the jet pump and hull; marine organisms and corrosion
Sea-Doo (2026 GTI, GTR and Wake operator's guide, pp. 168-169)Remove the watercraft from the water every day; never leave it in water for storageNo reason given next to the instruction

What happens to a jet ski left in the water

The makers name the damage, and BoatUS's insurance claim files show what happens to boats kept afloat. Here is each risk and who says so.

Marine growth

Yamaha's 2026 VX manual counts marine organisms among the conditions that can shorten the life of many watercraft components, and Sea-Doo's 2026 guide tells owners to remove marine organisms from the inside and outside of the hull when they clean it. Discover Boating says keeping a boat out of the water when it's not in use can help protect it from marine growth, as well as wakes, storms, corrosion and hull damage.

Check the intake as well as the hull. Before each ride, Sea-Doo's guide says to inspect the ride plate and water inlet grate and remove weeds, shells, debris or anything else that could restrict the flow of water and damage the propulsion unit.

Band of green-brown algae, small barnacles and a few dark mussels along the waterline of a white personal watercraft hull lifted out of the water

Corrosion and hull blistering

Kawasaki names two kinds of damage from prolonged immersion: hull paint that bubbles and peels, and electrolytic erosion of some metal parts in the jet pump. For boats in general, BoatUS's winterizing guide says a hull that gets the chance to dry out for several months each winter is less likely to develop blisters than a hull that remains in the water. Yamaha's 2021 Maintenance Matters guide says corrosion attacks a WaveRunner inside and out, every day, and that even riders in fresh water have corrosion-mitigation duties to attend to.

Swamping and sinking

Sea-Doo's 2026 guide says that because combustion engines need air to operate, the watercraft cannot be totally watertight. Sea-Doo's owner page on water in the hull adds that rainwater can seep in through a seat left ajar during storage, and that its onboard bailer system uses the suction of the jet pump to pull water out of the hull as you ride. Yamaha's 2026 VX manual warns that if the stern drain plugs aren't tightened securely before launching, water may flood the engine compartment and cause the watercraft to submerge.

BoatUS's claim files show where boats go down. Its April 2014 analysis of a year of sinking claims found that boats sink at the dock more than twice as often as they sink underway, and that the gradual failure of a part below the waterline is the single most common reason boats sink at the dock. Most of the swamping cases involved trailerable boats left tied to a dock with the stern open to the fetch. BoatUS's winterizing guide adds that owners who don't regularly visit boats kept in the water become vulnerable to the slow failure of a small underwater fitting, and that boats stored in the water are much more vulnerable to damage from the rise and fall in water level, high winds and torrential rains that come with strong winter storms. Those findings are about boats in general; none of the three jet ski makers' manuals cited here gives a sinking figure.

Electrical

Kawasaki puts part of the damage down to electrolytic erosion of metal parts in the jet pump. Discover Boating's PWC maintenance guide says the sacrificial anodes protect the pump system from galvanic corrosion, and to replace them if they're more than 50 percent worn. Yamaha's 2021 guide lists electrical connections and exposed metal components among the places corrosion can happen. Two more points, one for the dock and one for a craft that sits unused:

  • Dock power. BoatUS warns that an electric cable drooping into the water can electrocute anyone swimming or falling into the water close to the dock, which is known as Electric Shock Drowning.
  • The battery. Kawasaki's 2026 manual says that if the craft won't be used for more than two weeks, remove the battery and keep it fully charged with a maintenance charger.

Theft

The National Insurance Crime Bureau (NICB) says personal watercraft were the most stolen type of watercraft in 2021, with 1,292 thefts, and had the lowest recovery rate, 37 percent. Its advice is "Dock It and Lock It": a watercraft properly docked and locked with a steel cable and trailer hitch lock can help prevent theft, NICB says. BoatUS's winterizing guide says boats in gated or patrolled facilities are much less likely to be stolen. On a Sea-Doo, the D.E.S.S. key carries a radio-frequency chip with a code paired to the craft, and Sea-Doo says it acts as a means to prevent theft or unauthorized use when the craft is unattended. More in how to protect a jet ski from theft.

Salt water vs fresh water

Kawasaki and Sea-Doo add steps for salt water. Yamaha's 2021 Maintenance Matters guide asks for the same fresh-water flush after every ride, fresh or salt, and moves the exterior rinse and protectant spray from periodic to every ride in salt water. None of the three treats fresh water as exempt: Kawasaki still wants the craft out of fresh water after each use, and Yamaha's 2021 guide says all water, fresh or salt, contains contaminants that eventually build up in the cooling passages. Here is what each maker asks for after a ride:

Post-ride steps from each maker's guide, read October 2026. Yamaha's 2021 guide says to flush after every use, fresh or salt.
MakerAfter a ride in fresh waterAfter a ride in salt water
Kawasaki (2026 STX 160 manual, p. 142)Remove the craft from the water after each use, then purge the exhaustFlush the cooling system with fresh water after each use; after use at sea, rinse the engine compartment with fresh water
Sea-Doo (2026 GTI, GTR and Wake guide, pp. 161, 168)Remove the watercraft from the water every day; flush the exhaust when it won't be used again that day (p. 161)Flush the exhaust system daily (in foul water too); rinse the bilge area with fresh water
Yamaha (2026 VX manual, p. 100; 2021 Maintenance Matters guide)2026 VX manual: take it out of the water and flush the cooling passages. 2021 guide: flush after every use; exterior rinse and protectant spray periodically2026 VX manual: the same steps. 2021 guide: the same flush, plus the exterior rinse and protectant spray after every use; it calls salt water naturally corrosive

Sea-Doo is blunt about skipping the salt-water care: its 2026 guide says that failing to rinse the watercraft, flush the exhaust system and apply anticorrosion treatment after use in salt water will result in damage to the watercraft and its components, and that flushing with fresh water is essential to neutralize the corroding effects of salt. Yamaha's 2021 guide calls salt water naturally corrosive. Discover Boating explains why the engine bay needs a rinse too: in salt water, a salty mist can enter the engine compartment through the ventilation system and corrode the throttle linkage, electrical connections and other components. Its flushing guide applies the flush to fresh water that's silty or sandy as well.

Fresh water and winter. For boats, Discover Boating says year-round storage in the water is usually considered acceptable in temperate areas with mild winters, or with the boat completely winterized in its slip and an agitator (ice eater) keeping the water around it from freezing. If the marina loses power and the agitator stops working, it says, the hull could become frozen in place and ice damage can occur. The jet ski makers' every-day rule comes with no seasonal exception; winter plans for a jet ski are in jet ski winter storage.

The equipment. Salt water affects the lift as well as the craft. Discover Boating says saltwater boaters should choose a lift with corrosion-resistant materials and stainless steel fasteners, and some PWC lift warranties cover fresh-water use only: Hewitt's says so, and so does Sunstream's for its Dock Jock lifts.

How long can you leave a jet ski in the water?

None of the sources behind this guide gives a number of days a jet ski can safely float: not the 2026 owner's manuals from Kawasaki, Yamaha or Sea-Doo, not BoatUS, and not Discover Boating. Here is what they do say:

  • Kawasaki: out of the water at the end of each day's use, and not in the water overnight.
  • Sea-Doo: out of the water every day, and never left in the water for storage.
  • Yamaha: out of the water after using it. The manual says extended periods in the water speed up wear, without putting a number on extended.
  • BoatUS, for boats: its claim files suggest a boat is less likely to sustain damage, in the short and the long run, if left for long periods on land rather than in the water.

So the makers' limits run out with the day's riding, and none of the sources here publishes a safe number of days.

Note

Kawasaki's week counts are about idle time

Kawasaki's 2026 STX manual (p. 143) does give time spans, for a craft that sits unused: if it won't be used for more than a week, lubricate the internal engine components to help prevent corrosion; for more than two weeks, remove the battery and keep it fully charged with a maintenance charger. These are not limits for time in the water: the same checklist opens by saying to take the craft out at the end of each day's use.

How to keep a jet ski at a dock between rides

If you're looking up how to store a jet ski in the water, the makers' answer is that storage happens out of it. Tying up for a lunch stop or between rides is different, and Sea-Doo's docking guide and BoatUS cover how to do it.

Tying up for the day

Better options: a lift or a drive-on floating dock

Both keep the hull out of the water at the waterfront, which is what the manuals ask for.

A lift. BoatUS's winterizing guide says storage on lifts can be the best of both worlds, with most of the advantages of storage ashore while you can still use the boat when the weather is good. Lifts have limits: BoatUS's lift article says high winds may dislodge a boat from its bunks and that straps around the boat will help keep it in place, and it pictures a lift that collapsed after one of its wire cables rusted through. Magnum says no portion of its RotoMag lift, which swings the craft over the pier, is permanently in the water, so there's no threat of marine growth on the lift.

A drive-on floating dock. These ports are floating platforms you drive the craft onto. EZ Dock says its ports let owners store their craft out of the water, and Jet Dock calls its drive-on system a way of parking a jet ski out of the water. A floating lift stays in the water itself, and Discover Boating notes that its components can be exposed to marine growth and may require occasional cleaning. ShoreMaster, which sells floating lifts, calls them the ideal solution for deep lakes, fluctuating rivers or saltwater marinas.

Empty light-gray floating drive-on port tied alongside a wooden dock, with two rows of black rollers in its cradle, on a calm lake

The trailer. Sea-Doo's owner page on water in the hull suggests storing the craft on its trailer with the drain plugs loose and the bow slightly elevated, so rainwater doesn't collect inside. Yamaha's 2026 VX manual says to store it upright in a horizontal position, so follow the manual for your own model.

For the choice between a lift and a port (water depth, the bottom, changing water levels, capacity and permits), see storing a jet ski on a lift or dock. Published marina and storage rates are in jet ski storage cost.

Covering a jet ski once it's out of the water

On a lift or a port, or on a trailer parked outside, the craft sits outdoors in sun, rain and wind. BoatUS's winterizing guide says a cover is even more important for a boat stored on a lift, and Sea-Doo counts covering a stored craft to ward off rainwater among the steps that go a long way toward eliminating water intrusion. Fit the cover once the hull is out of the water. A craft that's still floating is a different case: get it out of the water first.

For a jet ski out of the water, whether on its trailer or on a lift or drive-on port, use an outdoor cover such as our Weatherproof Shield: water-resistant 600D solution-dyed polyester with a PU coating, an elastic hem cord, built-in buckles and straps, and air vents to aid trailering. It comes in seven sizes by overall length, so measure bow to stern and match the number in the size guide, or browse all jet ski covers. It carries a Lifetime warranty; see the warranty page. Parking, drainage and locks for a craft kept outdoors are in is it okay to store a jet ski outside?

Jet ski raised clear of a river on a galvanized lift beside a wooden dock, under a gray and black AllGuard Weatherproof Shield cover

Trailerable Cover

AllGuard Weatherproof Shield Jet Ski Cover (Trailerable)

Outdoor cover for a jet ski out of the water, on a trailer, lift or port: water-resistant 600D PU-coated polyester, elastic hem cord, built-in straps and buckles. Seven sizes by overall length.

4 colors: Blue / Black, Gray / Black, Red / Black, Yellow / Black

  • Under 90 inP0
  • Under 102 inP1
  • Under 115 inP2
  • Under 125 inP3
  • Under 135 inP4
  • Under 145 inP5
  • Up to 160 inP6

Lifetime Warranty

Size the cover to the craft

Measure overall length, bow to stern, then match the number in the size guide.

Open the size guide

Leaving a jet ski in the water: FAQ

Kawasaki says no: its 2026 STX 160 manual says to remove the craft from the water at the end of each day's use and not to leave it in overnight. Yamaha's 2026 VX manual says to take it out after using it, and Sea-Doo's 2026 GTI, GTR and Wake guide says to remove it from the water every day.

Sources

  1. JET SKI STX 160LX / STX 160X Owner's Manual (2026): End of the Day Checklist (pp. 142-143); Transporting and Storage (p. 147) (opens in a new tab)Kawasaki Motors Corp., U.S.A. · 2026 manual; read 2026-10-27
  2. 2026 WaveRunner VX Owner's/Operator's Manual, U.S.A. Edition (LIT-18626-15-77): Post-operation care (p. 100); drain plugs (pp. 74, 83) (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2026 manual; read 2026-10-27
  3. GTI, GTR and Wake Series Operator's Guide 2026: Jet Pump Water Intake (p. 38); watertightness (p. 123); Flushing (p. 161); Watercraft Care (pp. 168-169) (opens in a new tab)BRP (Sea-Doo) · 2026 guide; read 2026-10-27
  4. GTX Series Operator's Guide 2026: Watercraft Care (pp. 151-152) (opens in a new tab)BRP (Sea-Doo) · 2026 guide; read 2026-10-27
  5. Yamaha WaveRunners 2021 Maintenance Matters Guide (Corrosion Prevention; flushing) (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2021
  6. What do I do if water gets in the Sea-Doo? (opens in a new tab)BRP (Sea-Doo) · retrieved 2026-10-27
  7. How to Dock a Personal Watercraft (opens in a new tab)BRP (Sea-Doo) · retrieved 2026-10-27
  8. What is a personal watercraft Learning Key? (opens in a new tab)BRP (Sea-Doo) · retrieved 2026-10-27
  9. Keeping Your Boat Afloat (analysis of a year of sinking claims) (opens in a new tab)BoatUS · 2014-04
  10. The Boater's Guide to Winterizing (opens in a new tab)BoatUS · 2021-09 (PDF date); retrieved 2026-10-27
  11. Give Your Boat A Lift (opens in a new tab)BoatUS · 2021-09
  12. How to Choose the Right Boat Lift (opens in a new tab)Discover Boating (NMMA) · retrieved 2026-10-27
  13. How to Flush a Jet Ski, WaveRunner or Personal Watercraft (PWC) (opens in a new tab)Discover Boating (NMMA) · retrieved 2026-10-27
  14. Personal Watercraft (PWC), WaveRunner & Jet Ski Maintenance Guide (opens in a new tab)Discover Boating (NMMA) · retrieved 2026-10-27
  15. Boat Storage Guide: Indoor Boat Storage, Dry Storage & Outdoor (opens in a new tab)Discover Boating (NMMA) · retrieved 2026-10-27
  16. Watercraft Thefts May Be Down In 2021, But Owners Should Stay Vigilant. Dock It and Lock It! (opens in a new tab)National Insurance Crime Bureau (NICB) · 2022-08-29
  17. Floating Boat Lifts (opens in a new tab)ShoreMaster · retrieved 2026-10-27
  18. RotoMag Rotating PWC Lift (opens in a new tab)Magnum Lift · retrieved 2026-10-27
  19. 1200# PWC Lift-96"X102" (warranty text) (opens in a new tab)Hewitt · retrieved 2026-10-27
  20. Sunstream FAQ's (warranty) (opens in a new tab)Sunstream Boat Lifts · retrieved 2026-10-27
  21. PWC Ports (opens in a new tab)EZ Dock · retrieved 2026-10-27
  22. Jet Ski Lift: Floating Jet Ski Docks & PWC Lifts (opens in a new tab)Jet Dock · retrieved 2026-10-27

Find Your Size

Measure your jet ski bow to stern in a straight line, then enter the length in inches.

  1. Under 90 inP0
  2. Under 102 inP1
  3. Under 115 inP2
  4. Under 125 inP3
  5. Under 135 inP4
  6. Under 145 inP5
  7. Up to 160 inP6
Full Size Guide

In inches. Decimals are fine.

Covers for Your Jet Ski

All Covers