AllGuard Weatherproof Shield
Outdoor storage and trailering
$139.99
Lifetime WarrantyStorage
None of the makers' manuals and guides cited here gives a maximum time a jet ski can sit. What Yamaha, Sea-Doo and Kawasaki do publish are time frames for the fuel, the battery and the engine, and here they are, source by source.
None of the jet ski makers' manuals and guides cited here gives a maximum number of days a craft can sit. What they do give is a time frame for each job. Kawasaki's 2026 owner's manuals call for the full storage procedure whenever the watercraft "will not be in use for more than 30 days." Yamaha's 2026 owner's manuals take the battery out if the craft "will not be used for more than a month." BRP's 2026 Sea-Doo operator's guides say not to run the engine at all once it's in storage. And Yamaha's 2021 Maintenance Matters guide warns that today's gasoline "can begin to break down in a matter of weeks, not months."
So the answer depends on how the craft was put away. Prepared the way your owner's manual describes, a jet ski can sit through an off-season; that's what the makers' storage procedures are for. Left as it was after the last ride, the clock runs faster: on land, the shortest time frames in the makers' documents are a week or two, and in the water, Kawasaki's is a single day. Below are those time frames in each source's own words, then the fuel and battery details, how to start a jet ski that has been sitting, how to prepare one for a longer layoff, and how to clean one that sat in the water.
Note
Your owner's manual has the last word
Yamaha, Sea-Doo and Kawasaki disagree on some storage steps, the fuel tank level most of all. Each maker's instruction below names the document it comes from. Where your manual for your model and year says something different, follow the manual.
The table lists the time frames that appear in the manufacturers' manuals and web guides, BoatUS's winterizing guide and one fuel-stabilizer maker's instructions, roughly shortest first, each in the source's own wording.
What it doesn't have are the day bands some online summaries use, such as 0 to 30, 30 to 90 and 90-plus days. None of the sources cited here groups sitting time that way, and none of them sets a maximum time a craft can sit. Where a source gives a reason for its time frame, the sections after the table include it.
| Time frame (the source's wording) | Source | What the source says |
|---|---|---|
| "Within a week" of buying the gas | Yamaha WaveRunners article "Getting Your PWC Ready for the Season" (2022) | Gas you'll use within a week of buying it doesn't need a stabilizer, per Yamaha's Steve Friedrich; he recommends a continual-use additive such as Yamaha's Engine Med RX at every fill-up instead. |
| "A matter of weeks, not months" | Yamaha Maintenance Matters guide (2021) | How soon today's gasoline can begin to break down. Treat every tank of fuel, not just for extended storage. |
| "A week or more" | Yamaha 2026 VX, SuperJet, JetBlaster and JetBlaster PRO owner's manuals | Rustproof the internal engine components to help prevent corrosion, using the manual's rustproofing procedure. |
| "More than a week" | Kawasaki 2026 STX 160LX/160X and Ultra 310LX owner's manuals | Lubricate the internal engine components to help prevent corrosion. |
| "More than two weeks" | Kawasaki 2026 STX 160LX/160X and Ultra 310LX owner's manuals | Remove the battery and keep it fully charged using a maintenance charger. |
| "Every 2 weeks" above 16 °C (60 °F); "every month" below | BRP 2026 Sea-Doo Spark operator's guide | How often to recharge a battery in storage. The battery must always be stored fully charged. |
| "At least twice a month" | Yamaha Maintenance Matters guide (2021) | For a craft stored outdoors: check and drain the footwells, because even units with factory covers can collect water there. This is a footwell check, not a battery interval. |
| "Even a few weeks" | BoatUS, The Boater's Guide to Winterizing (2021) | Unless you're in Hawaii or the Florida Keys, winterize the engine even for a layup this short, to minimize the chance that a sudden freeze puts it out of commission. |
| "Monthly"; "about once a month"; "at least once a month" | Yamaha Maintenance Matters (2021); Kawasaki 2026 manuals; BoatUS winterizing guide (2021) | Yamaha: check the battery's charge monthly and keep it topped off. Kawasaki: give a stored battery a slow charge of one ampere or less about once a month. BoatUS: for a battery kept aboard and left unplugged, charge it completely at least once a month. |
| "More than a month" | Yamaha 2026 owner's manuals (all nine U.S. editions) | Remove the battery, check it and store it in a cool, dry place. Storing it uncharged can cause permanent battery damage. |
| "30 to 60 days" | Kawasaki 2026 STX 160LX/160X and Ultra 310LX owner's manuals | Mix a fuel stabilizer, such as STA-BIL, with the gasoline in the fuel tank. |
| "30-days or longer" | Gold Eagle, maker of STA-BIL Storage Fuel Stabilizer (product page) | The stabilizer maker's own product claim: use it in any gasoline-powered vehicle or equipment stored this long. It doesn't change your manual's tank-level or draining instructions. |
| "More than 30 days," or "during the winter" | Kawasaki 2026 STX 160LX/160X and Ultra 310LX owner's manuals | Proper storage is essential: the full storage procedure, by a Kawasaki dealer or by you. Kawasaki recommends draining all fuel from the tank and fuel system before storage. |
| "A month or more" | BoatUS, The Boater's Guide to Winterizing (2021) | Winterize the boat, wherever you keep it. |
| "A prolonged period, such as winter storage" | Yamaha 2026 owner's manuals (all nine U.S. editions) | Top off the fuel tank with fresh gasoline and add Yamalube Fuel Stabilizer & Conditioner Plus. The manuals say storage this long requires preventive maintenance to ensure against deterioration. |
| "The storage period" | BRP Sea-Doo operator's guides (all 13 reviewed, dated 2003 to 2027) | Do not run the engine during the storage period. |
| "Long-term storage" | BRP article "How to Winterize Your PWC" (June 9, 2026) | Even without freezing weather: stabilize the fuel, fog the engine and disconnect the battery. |
Fuel gets some of the shortest time frames. Yamaha's 2021 Maintenance Matters guide says today's gasoline can begin to break down in a matter of weeks, not months, and tells owners to treat every tank of fuel, not just for extended storage. The makers say what the stabilizer is for: Kawasaki's 2026 manuals say stabilizer additives inhibit oxidation of the fuel, which minimizes gummy deposits, and BRP's 2026 Sea-Doo guides add one to prevent fuel deterioration and fuel system gumming.
Water is the other concern. Maintenance Matters says water can form in the fuel system during extended storage through natural condensation, and that ethanol fuels can draw water directly from the atmosphere through the tank's vent. BoatUS's winterizing guide, written for boats in general, describes what can follow with E10: if the ethanol absorbs enough moisture over the winter, it can separate from the gasoline and leave a caustic mixture at the bottom of the tank that can damage the engine. BoatUS calls this phase separation and says only emptying the tank prevents it completely; if that isn't practical, it adds stabilizer and fills the tank to 95 percent to allow for expansion.
The makers disagree, so follow your manual:
One stabilizer maker publishes its own numbers. Gold Eagle, which makes STA-BIL, the brand Kawasaki's manuals name as an example, says to use its Storage Fuel Stabilizer in anything you plan to store for 30 days or longer. That is the product maker's claim, not a manufacturer's storage limit, and it doesn't change your manual's tank-level or draining instructions.
Yamaha's 2022 article on getting a PWC ready for the season says fuel that was conditioned properly for storage should be fine. If it wasn't, especially if it contains ethanol, the article says to empty the tank and fill it with fresh fuel. Maintenance Matters is blunt about the alternative: no additive will restore stale fuel, remove water or cure ethanol-related issues. Don't pour old gasoline out; Kawasaki says never to discard it, and to return it to an authorized recycling center.

A battery loses charge as it sits. BRP's 2026 Spark guide says storing it in a cool, dry place reduces self-discharging, and that regularly charging it during storage will prevent cell sulfation. The makers' calendars differ:
Two cautions from the manuals. BRP says never to charge or boost the battery while it's installed in the watercraft. And Yamaha's 2026 manuals say a VRLA (valve-regulated lead-acid) battery needs a special constant-voltage charger, because a conventional charger will damage it.
Chargers, maintainers and the charging steps are covered in how to charge and store a jet ski battery. If the battery is flat every time the craft has sat, start with why does my jet ski battery keep dying?

None of the makers' manuals and guides cited here tells owners to start a stored jet ski now and then, and BRP's guides say not to. Its 2026 Sea-Doo operator's guides carry the notice "Do not run the engine during the storage period." The same notice appears in all 13 Sea-Doo guides, dated 2003 to 2027, reviewed for our Sea-Doo winterizing guide. Yamaha's and Kawasaki's 2026 owner's manuals give no instruction to run the engine while the craft is stored. Their storage procedures protect the engine with a rustproofing or fogging step instead (on some Yamaha models, a dealer does it) and take the battery out.
For shorter breaks, the steps the makers do give are protective ones, not engine runs. If the craft won't be used for more than a week, Kawasaki's 2026 manuals say to lubricate the internal engine components to help prevent corrosion, and Yamaha's 2026 VX, SuperJet and JetBlaster manuals rustproof them if it will be stored for a week or more.
If you do run the engine on land, for a flush or a first start after storage, stay inside your maker's limit. Yamaha's 2026 manuals allow no more than 15 seconds without supplying water. Kawasaki's 2026 STX manual allows no more than 15 seconds at a time out of the water, and never at maximum speed; its flushing procedure, with a garden hose connected, idles the engine for several minutes with the water running. BRP's 2026 guides say never to run the engine without water supplied to the exhaust system, and never for longer than 2 minutes.
Each maker has its own name for bringing a stored craft back. Kawasaki's owner's manuals have a Removal from Storage section, which the 2026 STX 160LX/160X manual introduces as the steps needed to put the watercraft back in service following a storage period. BRP's 2026 Sea-Doo guides call it preseason preparation and say to perform every task in the maintenance schedule's Every Year or 100 Hours table; BRP recommends, but doesn't require, an authorized dealer for it. Yamaha's 2026 manuals have no separate after-storage section, so start with their pre-operation checklist, which they say to run each time the watercraft is used, and Yamaha's 2022 season article.
The sequence below draws on those sources. It's a summary: the full routine, with each maker's battery, oil, spark plug and trailer checks, is in how to de-winterize a jet ski.

Take the cover off and remove the seat. Yamaha's 2026 manuals say to leave the engine compartment open for a few minutes so fuel vapors can escape; Kawasaki's 2026 STX manual opens the front hatch cover, removes the seats and opens the inspection vent hatch for several minutes. If you smell gasoline or find a fuel leak, don't start the engine: Yamaha says not to, and BRP says not to apply electrical power or start it. Run the engine only in a well-ventilated area, never indoors; BRP and Kawasaki both warn that the exhaust contains carbon monoxide.
Kawasaki's Removal from Storage list checks all rubber hoses, and the cooling and bilge hoses, for weathering, cracking or looseness, and Yamaha's 2022 season article says fuel and water lines should be soft and supple. Then handle the fuel the way your maker stored it: Kawasaki's list fills the drained tank and closes the filler cap securely, and Yamaha's season article empties and refills a tank that wasn't conditioned for storage. Yamaha's 2026 pre-operation checklist also has you drain any water that has collected in the water separator.
Charge it outside the craft; BRP says never to charge or boost the battery while it's installed. Clean the terminals, then connect the positive cable first, as Yamaha's, BRP's and Kawasaki's 2026 manuals all specify; Yamaha's and BRP's connect the negative (black) cable after it.
Check the oil level before the first start, as your manual describes; Kawasaki's list says to top up with the specified oil if needed. Kawasaki's list also checks the spark plugs. BRP's 2026 guides replace them every 2 years or 200 hours, and Yamaha's 2026 VX manual has a Yamaha dealer check them at the first 10 hours, then every 100 hours or 12 months.
Kawasaki's list checks that the throttle, steering and reverse don't bind or stick, and that the drain screws in the stern are securely tightened. Yamaha's 2026 VX manual makes sure the jet intake isn't damaged or clogged with weeds or debris, and BRP's guides inspect the ride plate and intake grate and clear anything that could restrict the water flow.
Kawasaki's Removal from Storage list runs the engine for 15 seconds and checks for fuel, oil and exhaust leaks, any of which must be repaired. For a longer run on land, connect a garden hose to your maker's flush fitting: all three makers start the engine first and then turn the water on, and turn the water off before stopping the engine. Then confirm that the engine stops with the stop switch and with the lanyard or tether, as the Yamaha and BRP pre-ride checks do.
Start the engine on the water only where it's deep enough. Yamaha's 2026 manuals say at least 60 cm (2 ft) from the bottom of the craft, BRP's 2026 guides at least 90 cm (3 ft) under the lowest rear of the hull with everyone aboard, and Kawasaki's 2026 STX manual at least 0.8 m (2.6 ft). If something can't be corrected with the procedures in the manual, Yamaha's 2026 manuals say to have the craft inspected by a Yamaha dealer.
For a long layoff, the makers' answer is the storage procedure, done before the craft sits rather than after. Kawasaki's 2026 manuals say proper storage is essential during the winter, or whenever the watercraft won't be in use for more than 30 days, and give two routes: your Kawasaki dealer, or the steps in the manual. Yamaha's 2026 manuals say storage for long periods, such as winter storage, requires preventive maintenance to ensure against deterioration; they call a dealer service before storage advisable, though the listed procedures can be performed easily by the owner. BoatUS draws its line at a month: if you won't use a boat for a month or more, winterize it, wherever it's kept.
Warm weather doesn't change that. BRP's June 2026 winterizing article tells owners in places like Florida and California to stabilize the fuel, fog the engine and disconnect the battery for long-term storage even without freezing weather. It lists what skipping winterization can cause: corrosion, fuel degradation, battery failure and even freezing damage.
The full procedures are in how to winterize a jet ski, with make-specific versions for Sea-Doo, Yamaha WaveRunner and Kawasaki owners. Where to keep the craft is covered in jet ski winter storage and the main jet ski storage guide.
Kawasaki's 2026 storage steps include covering the watercraft and storing it in a clean, dry place, and Yamaha's 2021 Maintenance Matters guide says to consider a cover when storing outdoors is the only option. Both makers note that a craft stored outside can still collect water in the footwells under a cover. Yamaha says to check and drain them at least twice a month; Kawasaki says to raise the trailer tongue so water can't accumulate there.
For a craft that sits outside or on its trailer, ours is the Weatherproof Shield: 600D solution-dyed polyester with a PU coating, water-resistant, with an elastic hem cord, built-in buckles and straps, air vents to aid trailering, an extra strap set and a mesh storage bag. It has a Lifetime warranty (see our warranty page). For a garage, the Satin Shield is an indoor-only stretch cover of 85% polyester and 15% spandex with a sheared fleece interior, and a satin storage bag is included. Both are sized by the craft's overall length: the jet ski cover size guide shows how to measure, and you can browse all our jet ski covers. A cover doesn't replace the fuel and battery steps above.
Trailerable Cover
AllGuard Weatherproof Shield Jet Ski Cover (Trailerable)
For a jet ski that sits outside or on its trailer: water-resistant 600D PU-coated polyester, an elastic hem cord, built-in buckles and straps, and air vents to aid trailering.
4 colors: Blue / Black, Gray / Black, Red / Black, Yellow / Black
$139.99
Shop the Weatherproof ShieldIn the water, the makers' time frame shrinks to a day. Yamaha's 2026 owner's manuals say that after using the watercraft you should always take it out of the water, clean it and store it, because leaving it in for extended periods accelerates the normal deterioration of the jet pump and hull; marine organisms and corrosion are among the conditions that can shorten the life of many components. Kawasaki's 2026 manuals are more specific: Jet Ski watercraft aren't designed to be docked in the water for extended periods, and prolonged immersion will make the hull paint bubble and peel and cause electrolytic erosion of some metal parts in the jet pump. Kawasaki's fix is to take the craft out at the end of each day's use and not leave it in overnight. Whether, and for how long, to keep one afloat is covered in can you leave a jet ski in the water?
Once it's out, these steps from the Yamaha, BRP and Kawasaki manuals and guides cover the craft itself.
BRP's 2026 guides say to remove the tether cord before cleaning the jet pump area or inspecting the intake grate. Kawasaki says the jet pump contains moving parts that can cause severe injury: stop the engine and pull the lanyard key off the stop button before checking the pump for debris.
BRP's 2026 GTI, GTR and WAKE guide washes the body and hull with a mild soap-and-water solution, rinses thoroughly with fresh water and removes marine organisms from the inside and outside of the hull. Yamaha's 2021 Maintenance Matters guide says to clean the hull as necessary and remove any marine growth or barnacles with a thorough washing. BRP lists products never to clean with, among them strong detergent, degreasing agents, ammonia, acetone and petroleum-based products, and Yamaha's guide warns that liquid dish soap can strip off important protectants.
Inspect the ride plate and intake grate for cracks or damage, and remove weeds, shells or anything else that could restrict the water flow; BRP says to see an authorized Sea-Doo dealer if an obstruction can't be removed. Kawasaki notes that the engine's cooling water comes from the jet pump, so any loss of pump performance may cause overheating. Its 2026 STX 160LX/160X manual cleans the water intake, drive shaft, impeller, jet pump housing, outlet and steering nozzle with the craft tipped onto its port side on a protective pad, and warns never to roll it onto its starboard side, which can let water in the exhaust run into the engine.
BRP's storage steps rinse the jet pump by spraying water through its inlet and outlet openings, with the engine off, then spray an anti-corrosive product on the propulsion parts. Yamaha's 2026 manuals wash down the hull, deck and jet pump with fresh water and then wipe them with a dry cloth.
Flush as your manual describes. Yamaha's 2026 VX manual flushes the cooling water passages to prevent them from clogging with salt, sand or dirt, and Maintenance Matters says all water, fresh or salt, contains contaminants that will eventually build up in those passages. Kawasaki flushes after each use in salt water to help prevent salt deposits and eventual cooling system blockage. BRP warns that skipping rinsing, exhaust flushing and anticorrosion treatment after salt-water use will damage the watercraft and its components.
After use at sea, Kawasaki rinses the engine compartment with fresh water; if water has accumulated there, it removes the drain screws in the stern to let it out, then reinstalls them. Yamaha's 2026 manuals rinse the engine and compartment with only a small amount of water, never high-pressure water, which could cause severe engine damage, and let the compartment air dry completely before the seats, or the SuperJet's hood, go back on.
BRP's 2026 pre-ride table inspects the sacrificial anodes every month, more often in saltwater use, and changes them if necessary; BRP's 2023 summer-prep article replaces an anode worn more than halfway. Look the hull over for the damage Kawasaki attributes to prolonged immersion: bubbling or peeling paint.
BRP's guides ask owners to stop the spread of aquatic invasive species: before leaving the water access, remove any visible plants, animals, mud or debris from the hull, intake grate, jet pump nozzle and trailer; drain and flush all water from the craft, its exhaust and bilge; and let everything dry completely (for 5 days or more, depending on local laws) before visiting another body of water.
Covers are sized by overall length. Measure bow to stern, then match the number in the size guide.
None of the manuals and guides cited here sets a maximum. What they give are time frames: Yamaha says today's gasoline can begin to break down in a matter of weeks; Kawasaki's 2026 manuals protect the engine after more than a week and take the battery out after more than two weeks; and Kawasaki calls for the full storage procedure after more than 30 days, while BoatUS says to winterize for a month or more. Prepared the way your owner's manual describes, a jet ski can sit through an off-season.
None of the jet ski makers' documents cited here gives a limit in months or years. Yamaha's 2026 storage procedure is written for long periods "such as winter storage," and Kawasaki's for the winter or more than 30 days. Kawasaki's 2026 manuals recommend draining the fuel before storage. After any long sit, follow your maker's after-storage steps, replace fuel that wasn't conditioned for storage, and have a dealer inspect anything the manual's procedures can't correct.
The makers' manuals and guides cited here don't call for it. BRP's 2026 Sea-Doo guides say not to run the engine during the storage period, and Yamaha's and Kawasaki's 2026 manuals give no instruction to start a stored craft. Their storage procedures fog or rustproof the engine and take the battery out instead.
Follow your maker's after-storage steps: Kawasaki's 2026 Removal from Storage list, the Every Year or 100 Hours tasks BRP's 2026 preseason preparation calls for, or Yamaha's 2026 pre-operation checklist. In short: air out the engine compartment, check the hoses and fuel, charge the battery and refit it positive first, check the oil and plugs, then run the engine briefly within your maker's out-of-water limit, or on a flush hose with the engine started before the water.
Yamaha's 2022 season article says fuel conditioned properly for storage should be fine. If it wasn't, especially if it contains ethanol, it says to empty the tank and fill it with fresh fuel. Yamaha's 2021 Maintenance Matters guide adds that no additive will restore stale fuel, and Kawasaki says to return drained gasoline to an authorized recycling center.
On your maker's schedule. BRP's 2026 Spark guide recharges every month below 16 °C (60 °F) and every 2 weeks above; Kawasaki gives a stored battery a slow charge of one ampere or less about once a month; Yamaha says to check the charge monthly. Kawasaki's 2026 manuals put the battery on a maintenance charger if the craft won't be used for more than two weeks.
Take it out, stop the engine and pull the lanyard or tether. Wash the hull with a mild soap solution and fresh water and remove any marine growth, clear the intake grate and jet pump of weeds and debris, rinse the pump, flush with fresh water as your manual describes, then dry the engine compartment and check the anodes. Kawasaki warns that prolonged immersion makes hull paint bubble and peel.
Measure your jet ski bow to stern in a straight line, then enter the length in inches.