AllGuard Weatherproof Shield
Outdoor storage and trailering
$139.99
Lifetime WarrantyMaintenance
The makers' manuals name a short list of reasons a jet ski battery goes flat: key-off draw, self-discharge, accessories, loose or corroded connections and the charging system. Here is what Yamaha, Sea-Doo, Kawasaki and two battery makers say about each, and how to narrow them down.
If your jet ski battery is flat every time the craft has sat for a while, the makers' own manuals name the suspects. Kawasaki's 2026 STX 160LX/160X and Ultra 310LX owner's manuals say electrical accessories "such as digital clocks and computer memory, also draw current from the battery even when the key is switched off," and that combined with hot temperatures, those key-off draws can take a battery "from fully charged to completely discharged in a matter of days." The same page says batteries continually self-discharge, and faster as temperatures rise.
So a battery that keeps dying doesn't point to a single cause. Between them, the jet ski makers and two battery makers name several: draw from the craft's electronics while it's off, the battery's own self-discharge, accessories or a key or tether left on, loose or corroded connections, a charging system that isn't putting the charge back, and a battery that no longer holds a charge. Below is what each source says about each one, then a sequence for narrowing it down built from those sources' own checks: rule out what was left on, check the connections, charge and test the battery, and take what's left to a dealer.
Note
Your owner's manual has the last word
Yamaha, Sea-Doo and Kawasaki word their battery instructions differently, and none of their 2026 manuals checked for this article gives owners a procedure for testing the charging system. Each instruction below names the document it comes from. Where the manual for your model and year says something different, follow the manual.
The table lists each cause the sources name, in their terms, with the document it comes from. The sections after it take them one at a time.
| Cause | What the source says | Source |
|---|---|---|
| Key-off draw | Electrical accessories such as digital clocks and computer memory draw current from the battery even when the key is switched off. Combined with hot temperatures, a battery can go from fully charged to completely discharged in a matter of days. | Kawasaki 2026 STX 160LX/160X and Ultra 310LX owner's manuals |
| Leaving the battery connected | Leaving it connected lets the electrical components (the clock, for example) discharge the battery and may even over-discharge it. If you won't ride for four weeks or more, disconnect the battery. | Kawasaki 2026 owner's manuals |
| Self-discharge | Batteries continually self-discharge; the rate depends on the type of battery and the temperature, and it rises as temperatures rise. Yuasa's FAQ adds that a battery not in use discharges every day, sometimes by up to 0.5 to 1%, and faster when the climate is warm. | Kawasaki 2026 owner's manuals; Yuasa battery FAQ |
| Occasional or short use | Used regularly, the craft's charging system helps keep the battery fully charged; used only occasionally or for short periods, the battery is more likely to discharge. | Kawasaki 2026 owner's manuals |
| Accessories | The battery tends to discharge more quickly if the craft is equipped with optional electrical accessories (Yamaha). Running accessories while the engine is off drains the battery slowly or quickly depending on which accessory is running (Sea-Doo). | Yamaha 2026 owner's manuals (all nine U.S. editions); BRP 2026 GTI, GTR and WAKE and GTX operator's guides |
| Key, tether or accessory mode left on | Always remove the ignition key after stopping the engine to keep the battery from discharging (Kawasaki). With the engine shut off by the START/STOP button and the tether cord left on, a Sea-Doo's electrical power shuts off after about 60 minutes to prevent battery discharge (BRP). Accessory mode drains power from the battery (Yamaha VX, FX and GP). | Kawasaki 2026 owner's manuals; BRP 2026 operator's guides; Yamaha 2026 owner's manuals |
| Added electronics | More advanced electronic systems, including some of the alarm and tracking systems the article goes on to describe, can draw down your batteries over time. | BoatUS, "From Locks to Lockdown" (January 2013) |
| Loose or corroded connections | Poor terminal connections and a corroded terminal (Yamaha), corroded or loose battery connections or a bad ground (Sea-Doo), and loose battery connections (Kawasaki) are each listed alongside a run-down battery for an engine that won't start. | Yamaha, BRP and Kawasaki 2026 troubleshooting charts |
| The charging system | A red battery lamp that lights while riding indicates a malfunction: turn off unnecessary electrical equipment and have the electrical and charging systems checked (Sea-Doo). Yuasa's FAQ lists a faulty charging system among the reasons a new battery can become unserviceable within a few days or weeks of installation. | BRP 2026 operator's guides; Yuasa battery FAQ |
| Sulfation | Sulfation occurs when a battery is left discharged for an extended time; once the sulfate crystallizes in the cells, the plates are permanently damaged and will not hold a charge. Kawasaki calls it a common cause of battery failure. | Kawasaki 2026 owner's manuals |
Two things work on a parked battery at once, according to Kawasaki's 2026 manuals. One is self-discharge: "Due to their internal composition, batteries continually self discharge." The rate depends on the type of battery and the temperature, and it climbs as temperatures rise. Yuasa's FAQ adds that a battery that isn't in use discharges every day, sometimes by up to 0.5 to 1%, and that the rate increases when the climate is warm.
The other is draw. Kawasaki's manuals say clocks and computer memory pull current from the battery with the key off. Odyssey, which makes AGM batteries, calls these small currents parasitic loads: its 2026 installation, operation and maintenance manual says a battery that appears to be at rest may be supplying a small amount of current to connected equipment such as radios, clocks and security systems, typically tens of milliamps, which over time consume significant amp hours. Its example is a boat with a 20 mA draw, docked for five months with the battery connected: over those 150 days, Odyssey says, the draw consumes more than 70 amp hours (0.02 A × 24 hours × 150 days = 72 amp hours).
Kawasaki's manuals put numbers on both, in two tables on the same page. Here is its current-drain table:
| Discharging current | Days from 100% charged to 50% discharged | Days from 100% charged to 100% discharged |
|---|---|---|
| 7 mA | 60 | 119 |
| 10 mA | 42 | 83 |
| 15 mA | 28 | 56 |
| 20 mA | 21 | 42 |
| 30 mA | 14 | 28 |
The same Kawasaki page names two conditions that make a flat battery more likely. One is heat: as temperatures rise, so does the discharge rate. The other is light use: when the craft is used regularly, its charging system helps keep the battery fully charged, but if it's used only occasionally or for short periods, the battery is more likely to discharge. Yuasa's 2025 motorcycle battery charging guide ties its charging advice to ride length: for riders who ride daily or a few times a week, it calls a monthly charge sufficient with regular long rides, but recommends a weekly or biweekly charge for shorter rides.
Kawasaki is also the maker that ties its disconnect instruction to draw. Leaving the battery connected, its manuals say, lets electrical components such as the clock discharge the battery and may even over-discharge it, and they say that if you won't ride for four weeks or more, you should disconnect the battery from the vehicle. BRP gives different reasons in its 2026 Spark guide: keeping the battery in the vehicle for storage "may lead to contacts degradation/corrosion and case damage if freezing occurs," and the guide says to always remove the battery from the vehicle for storage. Yamaha's 2026 manuals remove the battery if the craft won't be used for more than a month, without giving a reason.
Cold works the other way on Kawasaki's self-discharge table, which runs slowest at 0 °C (32 °F), but it carries its own risk for a battery that's already low. Kawasaki says the fluid in an inadequately charged battery can easily freeze in extremely cold weather, which can crack the case and buckle the plates, while a fully charged battery can withstand sub-zero temperatures with no damage. BRP's 2026 Spark guide says a discharged battery will freeze and crack where freezing conditions are experienced.
A battery left flat can also become one that won't hold a charge. Kawasaki calls sulfation a common cause of battery failure: it occurs when a battery is left in a discharged condition for an extended time, and once the sulfate crystallizes in the cells, the plates are permanently damaged and won't hold a charge. Kawasaki adds that battery failure due to sulfation is not warrantable.
Put together: a battery that's flat after a few weeks parked is a symptom, not a diagnosis. The sources above suggest two possible explanations: key-off draw, which Kawasaki says can take a battery from fully charged to completely discharged in a matter of days when combined with hot temperatures, or a battery that has stopped holding a charge. The checks below tell which: a full charge, a rest-voltage reading and a load test show whether the battery holds a charge. If it does, the cause is elsewhere in the craft, and the makers' troubleshooting sends a cause the owner can't find to a dealer.

Some of the draw is under the owner's control. The makers name three sources of it.
BRP's 2026 GTI, GTR and WAKE guide also describes a safeguard. In its note on accessories mode, it says that when the battery voltage drops below 12.3 V, the LOW BATTERY lamp lights and the electrical system shuts down after 75 seconds; at that point, the battery still has plenty of energy to crank the engine, and running it down to 12.3 V repeatedly won't damage it. On models with post-drive battery management, the system shuts itself down at 12.3 V or less "to ensure enough power remains to start the engine."
A battery can look dead when the trouble is between it and the craft. All three makers' 2026 troubleshooting charts list the connections alongside the battery itself:
Yamaha's 2021 Maintenance Matters guide describes what a bad connection does: loose connections can cause "frustrating intermittent issues or a full-time 'no run' condition," a dirty or corroded connection can impede electricity's ability to travel, and a terminal connection "may be corroded, yet appear clean." Its fix is to remove the terminal connection, clean both sides down to bare, shiny metal, then reinstall and tighten it. It also says to make sure no fuel fumes are present when making, breaking or checking battery connections. Yuasa's FAQ adds two upkeep points: clean the battery terminals to prevent corrosion, and keep the battery top clean, dry and free of dirt.
If you take the battery out to clean it, refit it the way your manual says; all three makers connect the positive cable first. Each maker's refit steps are in how to de-winterize a jet ski.

Yuasa, whose YTX20L-BS is the battery Kawasaki's 2026 STX manual lists for that craft, warns against guessing. Its motorcycle guide to a battery that has gone bad says the first step is to rule out the other potential causes: before you invest in a new battery, inspect the wiring, check whether the terminal connections are loose or corroded, and consider a professional inspection to make sure it isn't the alternator or another mechanical component. The same guide calls a battery tester the surefire way to determine a battery's health, and Yuasa's 2025 motorcycle battery charging guide says to check that the battery cables are securely fastened before assuming the battery is at fault.
The jet ski makers keep the electrical diagnosis with their dealers:
None of the 2026 owner's manuals and operator's guides checked for this article, nine from Yamaha, two from Kawasaki and three from Sea-Doo, gives an owner procedure for testing the charging system or measuring key-off draw.
What an owner can check is the battery itself, against the battery makers' published figures. Odyssey's manual says to take the reading at least four hours after charging, or at least 30 minutes after a discharge; Yuasa's FAQ refers to an open-circuit voltage that has stabilized. Each maker's figures are for its own batteries:
| Source | Battery it covers | Voltage figure | What the source says |
|---|---|---|---|
| Kawasaki 2026 STX 160LX/160X owner's manual | The craft's sealed battery (Yuasa YTX20L-BS) | Below 12.8 V | If you ride infrequently, check the battery voltage weekly with a voltmeter, and charge the battery if it drops below 12.8 V. |
| Yuasa battery FAQ (web page, undated) | Yuasa 12-volt batteries | 12.7 V or higher | One of the signs of a full charge: an open-circuit voltage stabilized at 12.7 V or higher. |
| Yuasa spring battery maintenance guide (web page, 2023) | Yuasa AGM batteries | About 12.8 V when fully charged | An AGM battery's full-charge voltage should read about 12.8 volts; Yuasa says its slightly different electrolyte influences the terminal voltage. |
| Yuasa spring battery maintenance guide (web page, 2023) | Yuasa conventional (flooded) batteries | At least 12.6 V | Checked with a voltmeter, the terminal voltage should read at least 12.6 volts; below that, a boost charge is required. |
| Yuasa battery maintenance and storage guide (web page) | Yuasa batteries in storage | Below 12.4 V | Recharge battery if voltage is below 12.4V. |
| Odyssey installation, operation and maintenance manual (2026) | Odyssey AGM2 batteries | 12.9 V at 100%; 12.6 V at 75%; 12.2 V at 50%; 11.9 V at 25%; 11.5 V at 0% | When stored at 77 °F (25 °C) or below, give a freshening charge at least once every two years or when the reading drops to about 12.2 V (about 50%), whichever comes first. |
A good reading doesn't settle it. Yuasa's spring maintenance guide says a battery may show good terminal voltage and still not be in the best state of health: deteriorated from corrosion or sulfation, it could be seriously short on capacity. It suggests a start test in the vehicle or a capacity test at a service center, and says most battery dealers will perform a simple electronic or electrical resistance test that can tell you the battery's state of health. Yamaha's Maintenance Matters guide points to a load test: if there's any question about a battery's performance, have it load tested, which it says any auto parts store can do, or you can do yourself with the right equipment. Odyssey's manual lists a half-CCA load test and a conductance test, the hand-held type it says auto parts shops generally use, among the ways to tell whether a battery has reached the end of its life or simply needs a full recharge.
Put together, the sources' checks make a sequence. Chargers and the charging steps themselves are covered in how to charge and store a jet ski battery.
Check that the ignition key is out (Kawasaki), the tether cord is off the engine cut-off switch (BRP) and accessory mode is off (Yamaha), and list any accessory or device that has been added. Each is a draw the makers or BoatUS name.
First make sure no fuel fumes are present: Yamaha's Maintenance Matters guide says so for making, breaking or checking battery connections, and in an enclosed area it says to leave the seat off for a few minutes and air out the space. Then look for loose or corroded terminals. Yamaha's chart tightens poor connections and cleans or replaces a corroded terminal; BRP's guides check, clean and tighten loose cables, and refer corroded or loose connections or a bad ground on an engine that won't start to a dealer.
BRP says never to charge or boost the battery while it's installed in the watercraft, and Yamaha's 2026 manuals say a VRLA battery needs a special constant-voltage charger because a conventional charger will damage it. Follow your maker's charging instructions.
Wait as long as the battery's maker says (Odyssey: at least four hours after charging), then compare the reading with that maker's figures in the table above.

A full voltage reading isn't the last word: Yuasa's spring guide says a battery with good terminal voltage can still be seriously short on capacity and suggests a capacity test at a service center, and Yamaha's 2021 guide says any auto parts store can load test a battery.
A battery that tests good off the craft but keeps going flat in it suggests, without proving, a draw or a charging-system fault: Yuasa's FAQ lists both among the possible reasons a new battery fails within days or weeks. None of the makers' manuals checked gives owners a test that tells them apart, so the check that settles it is a dealer's, the route Yamaha, Sea-Doo and Kawasaki give for battery warnings and discharged batteries their owners can't resolve.
How long a jet ski battery lasts, and how that varies by type, is covered in how long do jet ski batteries last? Two points from the sources here bear on a battery that keeps dying:
Chargers, maintainers, disconnecting and the storage steps are covered in how to charge and store a jet ski battery. The makers' instructions point the same way, with different timing:
Between rides, the switch-off habits above apply: key out, tether off, accessory mode off. For the off-season, the full routine is in how to winterize a jet ski, the time frames each maker gives are in how long can a jet ski sit unused?, and the rest of the upkeep is in our jet ski maintenance guide.
A cover is for the craft, not the battery: it doesn't change any of the battery steps above. For a craft that sits outside or on its trailer, ours is the Weatherproof Shield: 600D solution-dyed polyester with a PU coating, water-resistant, with an elastic hem cord, built-in buckles and straps, air vents to aid trailering, an extra strap set and a mesh storage bag. It has a Lifetime warranty (see our warranty page). For a garage, the Satin Shield is an indoor-only stretch cover of 85% polyester and 15% spandex with a sheared fleece interior, with a Satin storage bag included. Both are sized by the craft's overall length: the jet ski cover size guide shows how to measure, and you can browse all our jet ski covers.
Trailerable Cover
AllGuard Weatherproof Shield Jet Ski Cover (Trailerable)
For a craft that sits between rides outside or on its trailer: water-resistant 600D PU-coated polyester, an elastic hem cord, built-in buckles and straps, and air vents to aid trailering.
4 colors: Blue / Black, Gray / Black, Red / Black, Yellow / Black
$139.99
Shop the Weatherproof ShieldKawasaki's 2026 manuals give two reasons a parked battery runs down: batteries continually self-discharge, faster as temperatures rise, and electrical accessories such as clocks and computer memory draw current even with the key off. Kawasaki says to remove the battery and keep it fully charged using a maintenance charger if the craft won't be used for more than two weeks; Yamaha's 2026 manuals remove it if the craft won't be used for more than a month, and BRP's 2026 Spark guide says to always remove it for storage.
Yes, according to Kawasaki's 2026 manuals: clocks and computer memory draw current from the battery even when the key is switched off, and combined with hot temperatures, a battery can go from fully charged to completely discharged in a matter of days. Yamaha's 2026 manuals add that the battery tends to discharge more quickly if the craft has optional electrical accessories.
On a Sea-Doo, BRP's 2026 guides say that if the engine is shut off with the START/STOP button and the tether cord is left on the engine cut-off switch, the electrical power shuts off after about 60 minutes to prevent battery discharge. BRP also says never to leave the tether cord on when you get off the craft. Kawasaki says to always remove the ignition key after stopping the engine to keep the battery from discharging.
It depends on the battery. Kawasaki's 2026 STX manual says that if you ride infrequently, you should check the voltage weekly with a voltmeter and charge the battery if it drops below 12.8 volts. Yuasa's FAQ counts an open-circuit voltage stabilized at 12.7 volts or higher as one sign of a full charge, and Odyssey's 2026 manual puts its AGM2 batteries at 12.9 volts when fully charged and 12.2 volts at half charge. Odyssey takes its readings at rest; the table in this article lists each maker's figures.
Yuasa's battery FAQ lists the reasons a new battery can fail within days or weeks: a faulty charging system, a short circuit, dirty or loose terminals, excessive ignition-off or parasitic drains, a battery too small for the vehicle, or one that was inadequately activated or left too long without its initial charge. Yuasa's guide to a battery that has gone bad adds that before you invest in a new battery, you should inspect the wiring and check for loose or corroded terminal connections. If the condition remains, Yuasa says to contact a qualified technician.
Yes. Kawasaki's 2026 manuals say the fluid in an inadequately charged battery can easily freeze in extremely cold weather, which can crack the case and buckle the plates, while a fully charged battery can withstand sub-zero temperatures with no damage. BRP's 2026 Spark guide says a discharged battery will freeze and crack where freezing conditions are experienced.
The makers differ. Kawasaki's 2026 manuals say a run-down battery should be removed and charged, and that if that isn't practical, a booster battery of the same voltage (12 V) and jumper cables may be used. Yamaha's 2026 manuals also allow a 12-volt booster battery and jumper cables. BRP's 2026 Sea-Doo guides say never to charge or boost the battery while it's installed in the watercraft. Follow your own manual's procedure.
Measure your jet ski bow to stern in a straight line, then enter the length in inches.