Winterizing

How to Winterize a Yamaha WaveRunner

Yamaha's owner's manuals set out the winter storage routine, and they split on who fogs the engine. Here's the order, the model-by-model differences, and what Yamaha leaves to the dealer.

By Alex Quinn 21 min read

Jet ski on a trailer beside a snowy lake under a yellow and black AllGuard Weatherproof Shield cover

Knowing how to winterize a WaveRunner starts with knowing which Yamaha you own. Yamaha's 2026 owner's manuals share one care-and-storage routine: top off and stabilize the fuel, flush the cooling passages, clean and wax the craft, grease the moving parts, rustproof the engine and store the battery. The biggest difference is who fogs the engine: some give the owner a procedure, while the FX, GP, VX Cruiser HO and VX Limited HO manuals hand it to a Yamaha dealer. This guide follows Yamaha's own documents step by step and names the document behind each step. For how Sea-Doo and Kawasaki compare, see our main guide to winterizing a jet ski.

The Yamaha documents behind this guide

The newest are Yamaha's 2026 U.S. owner's/operator's manuals: nine of them, which together cover every 2026 model listed on Yamaha's manual site. Yamaha posts its U.S.-edition manuals on its official WaveRunner manual site, where you can look yours up by year and product. We also use Yamaha's 2021 Maintenance Matters guide and the Maintenance Matters page on Yamaha's WaveRunner site, which carries the same storage advice.

Yamaha's documents don't always agree with each other, and the storage chapter of the manual for your model and year is the one to follow. If your WaveRunner is older than the manuals named here, look up its manual before you start. Still deciding whether to winterize at all? See whether you need to winterize a jet ski.

Note

Yamaha's first advice: talk to your dealer early

Each 2026 manual says it is advisable to have the watercraft serviced by a Yamaha dealer before storage, then adds that the procedures it lists can be performed easily by the owner. Maintenance Matters has a tip for anyone booking the dealer: "Don't wait to call your dealer about winterization. The threat of the season's first freeze is too late!"

Supplies Yamaha's documents call for

Gather these first. Yamaha names its own Yamalube products in its manuals, and we list them as Yamaha does; your manual has the exact grease, oil and quantities for your model.

What Yamaha's storage steps use

How to winterize a WaveRunner in 9 steps

The order follows the Long-term storage section of Yamaha's 2026 manuals, with the inspection and oil change from Yamaha's 2021 Maintenance Matters guide added at the start. Fuel comes before the flush: the manuals' tip is to top off and stabilize the tank before starting the engine. The battery comes out last, after the steps that run the engine; the manuals cover it in a separate Battery care section.

Winterizing a Yamaha WaveRunner, step by step

  1. Step 1: Look the craft over

    Maintenance Matters puts a visual inspection first: remove the seat, check the bilge for any sign of oil or fuel, and look for anything damaged, missing or out of place. Repair or replace what you find. It also calls the time just before lay-up an excellent moment for routine annual maintenance and any outstanding service issues.

  2. Step 2: Change the engine oil and filter

    Don't wait for spring, Maintenance Matters says: the engine oil has been carrying away debris and potential corrosives from combustion, so replace it and the oil filter before you lay the craft up. Its basic schedule is an oil change every 50 hours or once a year, and for four-stroke WaveRunners it points to Yamalube 4W. The 2026 manuals recommend having a Yamaha dealer change the engine oil and filter, and say to consult a dealer if you do it yourself.

  3. Step 3: Top off and stabilize the fuel

    The 2026 manuals' tip for winter storage: top off the fuel tank with fresh gasoline and add one ounce of Yamalube Fuel Stabilizer & Conditioner Plus to each gallon of fuel in the tank before starting the engine. The 2019 manuals we read give the same tip. Yamaha's 2021 Maintenance Matters guide words it differently: run the storage amount of its Fuel Med RX treatment through the entire fuel system before shutting down, store with the tank 7/8 full, and never plug or cap the fuel tank vent, which allows for expansion and contraction. The 2026 VX manual's refueling steps say to stop filling about 2 in (50 mm) below the top of the tank and not to overfill, as fuel expands when it heats up. Where Yamaha's documents differ, follow the manual for your model and year. If you fill a gas can for the craft, Maintenance Matters says to add the treatment before filling it.

    Gloved hands pouring fuel stabilizer into a red gas can on a garage floor
  4. Step 4: Flush the cooling water passages

    Yamaha describes WaveRunners as raw-water cooled: they use the water they run in as cooling water. The 2026 manuals' flush: put the craft level; remove the seats (what else comes off varies by model, see the table below); connect the garden hose adapter to the hose; take the cap off the flushing hose connector and push and twist the adapter on until it's secure; connect the hose to a tap. Make sure the area around the craft is clear, start the engine, then immediately turn the water fully on so it flows continuously from the jet thrust nozzle. Idle for about 3 minutes, watching the engine; if it stops, turn the water off at once and start again. Then turn the water off, discharge the remaining water by squeezing and releasing the throttle lever quickly for 10 to 15 seconds, stop the engine, and refit the cap and seats. The SuperJet manual has you remove the hood instead and open the water gradually until it flows from the cooling water pilot outlet.

  5. Step 5: Clean, drain and dry it, then wax

    From the 2026 manuals: rinse the engine and engine compartment with a small amount of water, never at high pressure; drain the bilge; wipe the engine and compartment dry; wash the hull, deck and jet pump with fresh water and wipe them down; treat vinyl and rubber parts, such as the seats and compartment seals, with a vinyl protectant; spray metal parts of the hull, deck and engine with a rust inhibitor; and let the engine compartment air-dry completely before the seats (the hood, on the SuperJet) go back on. To drain the bilge on land, remove the stern drain plugs, raise the bow (on a slope, for example), wipe up what's left, check the plugs and their O-rings, and screw them back in until they stop. Then wax the hull with a non-abrasive wax. Maintenance Matters adds: make sure every area is bone-dry before you close it up.

  6. Step 6: Grease the cables and linkages

    Lubricate the points your manual lists with water-resistant grease; the 2026 manuals name Yamalube Marine Grease. Every 2026 manual we read lists the steering cable, and the others vary by model (the table below has each list). The manuals' tips say to disconnect the shift rod, the electric trim rod or, on the SuperJet, the steering cable from its ball joint before lubricating it. Maintenance Matters adds: grease every zerk with the grease your owner's manual stipulates, to help force out any water sitting there.

  7. Step 7: Rustproof the engine, or book the dealer

    Every 2026 manual says to spray the metal parts of the hull and engine with a rust inhibitor such as Yamalube Silicone Protectant & Lubricant. The internal engine is where the models split. The VX-C, VX, VX Deluxe, VX Cruiser, VX Limited, JetBlaster and SuperJet manuals give owners a procedure, and say to rustproof the internal engine components if the craft will be stored for a week or more. The FX, GP, VX Cruiser HO and VX Limited HO manuals say: "Have a Yamaha dealer rustproof the internal engine components." Maintenance Matters says fogging oil coats internal engine parts to help prevent rust and corrosion, and that due to the complexity of some WaveRunner air intake systems, fogging for long-term storage is best performed by a qualified Yamaha technician. Each owner procedure is in the model notes below.

  8. Step 8: Remove and store the battery

    The 2026 manuals say to remove the battery if the craft won't be used for more than a month: disconnect the negative (-) lead, then the positive (+), unhook the battery bands and lift it out. Clean the case with fresh water, clean dirty or corroded terminals with a wire brush, apply water-resistant grease (Yamalube Marine Grease) to the terminals, and store it in a cool, dry place. Yamaha warns that storing a battery uncharged can damage it permanently, and says to check it periodically. The manuals recommend having a Yamaha dealer check the voltage and charge the battery, and note that a VRLA (valve-regulated lead-acid) battery needs a special constant-voltage charger; a conventional charger will damage it. Maintenance Matters adds: charge it fully, have it load tested, check the charge monthly, and if the craft spends the winter outside, bring the battery indoors to a cool, dry place.

    Watercraft battery on a garage workbench with a maintainer clipped to its terminals, a wire brush and a tub of grease
  9. Step 9: Store it upright, sheltered and covered

    The 2026 manuals warn to always store the watercraft upright in a horizontal position; otherwise fuel could leak into the engine or engine compartment and create a fire hazard. Maintenance Matters recommends storing indoors or under a shelter when possible, and considering a cover when outdoors is the only option. For footwell water it suggests raising the bow of a trailered unit that has no footwell drains, and keeping a unit that has them in a horizontal position with the drain holes clear. That bow-up tip differs from the 2026 manuals' warning to store the craft upright in a horizontal position, so follow your manual. Leave the fuel tank vent open, and when you're done, cover the craft as described below.

Important

Three Yamaha warnings for the steps that run the engine

Never supply flushing water while the engine is stopped: Yamaha says the water could flow back through the muffler into the engine and cause severe damage. Don't run the engine above 4,000 r/min on land, or for more than 15 seconds without supplying water, or it could overheat (the SuperJet manual sets the same 15-second limit on land). And the manuals with an owner fogging procedure warn never to spray a flammable rust inhibitor on engine surfaces while the engine is hot.

Model notes: VX, FX, GP, JetBlaster, SuperJet

The 2026 manuals share the steps above but differ in places. The table covers three: what you take off before flushing, which points you grease, and who fogs the engine. Here is what each one says.

From Yamaha's 2026 U.S. owner's/operator's manuals for each model, and its 2019 and 2020 SuperJet manuals for the last row. "Yamaha dealer" means the manual says: "Have a Yamaha dealer rustproof the internal engine components."
Internal engine rustproofing (fogging)Before flushingGrease points listed
VX-C, VX, VX Deluxe, VX Cruiser, VX Limited (2026)Owner: fogging oil into the intake opening under the air filter case cover for 3 seconds, then idle 15 secondsRemove the seatsSteering cable (nozzle end); shift rod and ball joint on all but the VX-C
VX Cruiser HO, VX Limited HO (2026)Yamaha dealerRemove the seats and seat storage compartmentSteering cable (nozzle end); shift rod and ball joint
FX HO, FX Cruiser HO, FX SVHO, FX Cruiser SVHO, FX Limited SVHO (2026)Yamaha dealerRemove the seats and removable watertight storage compartment; open the stern storage compartmentSteering cable, electric trim rod and ball joint; shift rod and ball joint
GP HO, GP SVHO (2026)Yamaha dealerRemove the seats and seat storage compartmentSteering cable, electric trim rod and ball joint; shift rod and ball joint
JetBlaster, JetBlaster DLX, JetBlaster LTD (2026)Owner: same intake-opening method as the VX, after removing the seat and fire extinguisher holderRemove the seat and seat storage compartmentSteering cable (nozzle end); shift rod and ball joint on the DLX and LTD
JetBlaster PRO (2026)Owner: same intake-opening method as the VX, after removing the seat and fire extinguisher holderRemove the seat and seat storage compartmentSteering cable, electric trim rod and ball joint; shift rod and ball joint
SuperJet (2026)Owner: at fast idle, spray into the air intake duct through the breather hose joint until the engine stalls, 15 seconds at mostRemove the hood; open the water graduallyThrottle cable; steering cable ball joints and inner wire
SuperJet, two-stroke (2019 and 2020)Owner: at fast idle, spray through the hole in the silencer cover until the engine stalls, 15 seconds at mostRemove the hood; open the water graduallySteering cable points; see the manual for the full list

VX and JetBlaster: the owner fogging procedure

The 2026 VX-C/VX/VX Deluxe/VX Cruiser/VX Limited manual's steps: remove the seats; remove the plastic tie that holds the fuel hose to the holder on the starboard side of the air filter case; release the hooks on the port side and remove the air filter case cover; spray a rust inhibitor such as Yamalube Stor-Rite Engine Fogging Oil into the intake opening for 3 seconds; refit the cover and its hooks and fasten the fuel hose back to the holder using the plastic tie. Then, with the area clear and well ventilated, start the engine, let it idle for 15 seconds, stop it, and refit the seats. The 2026 JetBlaster and JetBlaster PRO manuals use the same method once the seat and fire extinguisher holder are off. Yamaha's 2019 VX manual uses the same method with fewer steps: the air filter case cover is lifted rather than removed, with a notice not to lift it forcefully, since the fuel hose secured to it could be damaged.

SuperJet: two methods, by model year

The 2026 SuperJet manual: remove the hood; loosen the clamp and remove the breather hose; with the area clear and well ventilated, start the engine and run it at a fast idle; quickly spray as much rust inhibitor as possible into the air intake duct through the breather hose joint, until the engine stalls or for 15 seconds at most; refit the breather hose and clamp, then the hood. It names Yamalube Stor-Rite Engine Fogging Oil or an equivalent, and warns never to pour or spray gasoline, or anything other than a rust inhibitor, into the duct. Yamaha's 2021 SuperJet manual describes the same method.

The 2019 and 2020 SuperJet manuals are for a two-stroke engine that runs on gasoline mixed with oil. Their storage warning is to turn the fuel cock knob to "OFF," otherwise fuel could leak into the engine or engine compartment. They fog through the hole in the silencer cover with the silencer cap off, until the engine stalls or for 15 seconds at most, and say to refit the silencer cap securely afterwards, otherwise water could get into the engine.

FX, GP and the VX HO models: dealer fogging

The 2026 manuals for the FX HO and FX Cruiser HO, the FX SVHO, FX Cruiser SVHO and FX Limited SVHO, the GP HO and GP SVHO, and the VX Cruiser HO and VX Limited HO give no owner procedure for the internal engine. Each says: "Have a Yamaha dealer rustproof the internal engine components." Yamaha's 2019 FX HO manual says the same. The rest of the storage routine is still listed for the owner, and the 2019 manuals we read give the same top-off-and-stabilizer fuel tip as the 2026 editions.

Not listed here? Yamaha's manual site also covers other models, such as the EX series. Check the Care and storage chapter of yours.

What Yamaha leaves to the dealer

Yamaha's documents split the work like this. Quotes are from the 2026 manuals unless noted.

  • Service before storage: "It is advisable to have the watercraft serviced by a Yamaha dealer prior to storage. However, the following procedures can be performed easily by the owner."
  • Oil and filter: "It is recommended to have a Yamaha dealer change the engine oil and the engine oil filter. However, if you choose to change the oil and filter on your own, consult a Yamaha dealer." Yamaha's 2021 Maintenance Matters guide puts it this way: "Can I change my own oil? Absolutely, but you don't have to."
  • Battery: "It is recommended to have a Yamaha dealer check the battery voltage and charge the battery."
  • Engine fogging: the dealer on the FX, GP, VX Cruiser HO and VX Limited HO; an owner procedure on the VX-C, VX, VX Deluxe, VX Cruiser, VX Limited, JetBlaster and SuperJet. Maintenance Matters: "Due to the complexity of some WaveRunner engine air intake systems, fogging for long term storage is best performed by a qualified Yamaha technician."
  • Corrosion care: Maintenance Matters says your dealer can help with, or even do, most general and preventive maintenance, but "corrosion mitigation is something you can only do yourself."
  • Wrapping: Maintenance Matters notes that many Yamaha dealers offer shrink-wrapping.

Does a WaveRunner need antifreeze?

Yamaha's documents reviewed here list no antifreeze step. Yamaha's 2021 Maintenance Matters guide describes WaveRunners as raw-water cooled, and Yamaha's storage steps flush the cooling passages with fresh water, then discharge the remaining water by squeezing and releasing the throttle with the water turned off. A text search of the nine 2026 manuals listed here and the 2021 Maintenance Matters guide found no antifreeze step and no mention of antifreeze. If you've seen advice to pump RV antifreeze through a WaveRunner, check it against your owner's manual or ask a Yamaha dealer first.

Other brands work differently. See our guides to winterizing a Sea-Doo and winterizing a Kawasaki jet ski.

Covering a WaveRunner for winter

Yamaha's first choice is indoors or under a shelter. When outdoors is the only option, Yamaha's 2021 Maintenance Matters guide suggests considering individual covers or a large cover, and it recommends Yamaha's own WaveRunner storage covers for when the craft isn't in use or is being trailered. It also notes that many Yamaha dealers offer shrink-wrapping. Whatever goes over the craft, Yamaha's footwell advice still applies: even units with factory covers can collect water in the footwells when stored outdoors, so check and drain them at least twice a month. For where to keep the craft, see jet ski winter storage.

Outdoors or on the trailer

If you'd like one of ours, the Weatherproof Shield is our outdoor and trailering cover: 600D solution-dyed polyester with a PU coating, water-resistant, with an elastic hem cord, built-in buckles and straps, air vents to aid trailering, an extra strap set and a mesh storage bag. It has a Lifetime warranty (see our warranty page).

Trailerable Cover

AllGuard Weatherproof Shield Jet Ski Cover (Trailerable)

For a WaveRunner wintering outdoors or on its trailer: 600D PU-coated polyester, water-resistant, with built-in buckles and straps. Sized by overall length.

4 colors: Blue / Black, Gray / Black, Red / Black, Yellow / Black

  • Under 90 inP0
  • Under 102 inP1
  • Under 115 inP2
  • Under 125 inP3
  • Under 135 inP4
  • Under 145 inP5
  • Up to 160 inP6

Lifetime Warranty

In a garage or storage unit

For indoor storage, the Satin Shield is a stretch cover of 85% polyester and 15% spandex with a sheared fleece interior and elastic front and rear hems. A satin storage bag is included. It's an indoor cover, not one for outdoor weather.

Jet ski on its trailer in a winter garage under a black AllGuard Satin Shield indoor cover

Getting the size right

Both covers are sized by the craft's overall length, not by make or model name. Measure your WaveRunner or look up its published overall length, then match it in the jet ski cover size guide. The Satin Shield goes up to 138 inches; a longer craft needs the Weatherproof Shield. You can also browse covers for Yamaha WaveRunners or every jet ski cover we make.

Find your cover size

Measure your WaveRunner's overall length, then match it to a size.

Open the size guide

Yamaha WaveRunner winterizing checklist

Run through this before you close the garage door or walk away from the trailer.

Before you close it up for winter

Yamaha WaveRunner winterizing FAQ

Following Yamaha's 2026 owner's manuals and its 2021 Maintenance Matters guide: inspect the craft, change the oil and filter, top off and stabilize the fuel, flush the cooling passages, clean, drain, dry and wax it, grease the points your manual lists, rustproof the engine (or have a dealer do it on models whose manual says so), remove and store the battery, and store the craft upright in a horizontal position, sheltered or covered.

Sources

  1. 2026 WaveRunner VX-C/VX/VX Deluxe/VX Cruiser/VX Limited Owner's/Operator's Manual, U.S.A. Edition (LIT-18626-15-77): Care and storage; Maintenance (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2026 model year; viewed 2026-10-27
  2. 2026 WaveRunner VX Cruiser HO/VX Limited HO Owner's/Operator's Manual, U.S.A. Edition (LIT-18626-15-76): Care and storage (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2026 model year; viewed 2026-10-27
  3. 2026 WaveRunner FX HO/FX Cruiser HO Owner's/Operator's Manual, U.S.A. Edition (LIT-18626-15-73): Care and storage (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2026 model year; viewed 2026-10-27
  4. 2026 WaveRunner FX SVHO/FX Cruiser SVHO/FX Limited SVHO Owner's/Operator's Manual, U.S.A. Edition (LIT-18626-15-72): Care and storage (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2026 model year; viewed 2026-10-27
  5. 2026 WaveRunner GP HO Owner's/Operator's Manual, U.S.A. Edition (LIT-18626-15-75): Care and storage (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2026 model year; viewed 2026-10-27
  6. 2026 WaveRunner GP SVHO Owner's/Operator's Manual, U.S.A. Edition (LIT-18626-15-74): Care and storage (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2026 model year; viewed 2026-10-27
  7. 2026 WaveRunner JetBlaster/JetBlaster DLX/JetBlaster LTD Owner's/Operator's Manual, U.S.A. Edition (LIT-18626-15-79): Care and storage (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2026 model year; viewed 2026-10-27
  8. 2026 WaveRunner JetBlaster PRO Owner's/Operator's Manual, U.S.A. Edition (LIT-18626-15-78): Care and storage (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2026 model year; viewed 2026-10-27
  9. 2026 WaveRunner SuperJet Owner's/Operator's Manual, U.S.A. Edition (LIT-18626-15-71): Care and storage (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2026 model year; viewed 2026-10-27
  10. 2021 WaveRunner SuperJet Owner's/Operator's Manual, U.S.A. Edition (LIT-18626-12-89): Rustproofing (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2021 model year; viewed 2026-10-27
  11. 2020 WaveRunner SuperJet Owner's/Operator's Manual, U.S.A. Edition (LIT-18626-12-56): Long-term storage; Rustproofing (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2020 model year; viewed 2026-10-27
  12. 2019 WaveRunner SuperJet Owner's/Operator's Manual, U.S.A. Edition (LIT-18626-12-09): Long-term storage; Rustproofing (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2019 model year; viewed 2026-10-27
  13. 2019 WaveRunner VX-C/VX/VX Deluxe/VX Cruiser/VX Limited Owner's/Operator's Manual, U.S.A. Edition (LIT-18626-12-15): Long-term storage; Rustproofing (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2019 model year; viewed 2026-10-27
  14. 2019 WaveRunner FX HO/FX Cruiser HO Owner's/Operator's Manual, U.S.A. Edition (LIT-18626-12-10): Long-term storage; Rustproofing (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2019 model year; viewed 2026-10-27
  15. Yamaha WaveRunners 2021 Maintenance Matters Guide (opens in a new tab)Yamaha Motor Corporation, U.S.A. · 2021
  16. Maintenance Matters (web page: Storage and Care; Extended Storage) (opens in a new tab)Yamaha Motor Corporation, U.S.A. · retrieved 2026-10-27
  17. Official Yamaha WaveRunners Manual Site (opens in a new tab)Yamaha Motor Corporation, U.S.A. · retrieved 2026-10-27

Find Your Size

Measure your jet ski bow to stern in a straight line, then enter the length in inches.

  1. Under 90 inP0
  2. Under 102 inP1
  3. Under 115 inP2
  4. Under 125 inP3
  5. Under 135 inP4
  6. Under 145 inP5
  7. Up to 160 inP6
Full Size Guide

In inches. Decimals are fine.

Covers for Your Jet Ski

All Covers