Winter storage

Jet Ski Cover vs Shrink Wrap vs Tarp for Winter

A fitted cover, shrink wrap and a tarp each keep weather off a stored jet ski in a different way, and each asks something different of you. Here's what the makers, BoatUS and a shrink-wrap supplier say about all three.

By Alex Quinn 22 min read

Jet ski on its trailer in a gravel side yard in late autumn, under a blue and black AllGuard Weatherproof Shield cover

Once a jet ski is winterized, something has to keep the weather off it until spring. For a craft stored outdoors, the makers and BoatUS between them name a fitted cover, shrink wrap and a tarp. The makers don't all point the same way. Yamaha's 2021 maintenance guide says Yamaha offers storage covers for WaveRunners and that many Yamaha dealers offer shrink-wrapping services. Sea-Doo's 2026 operator's guide says to cover a craft stored outside with an opaque tarpaulin, while Sea-Doo's US winterizing page calls for a breathable, fitted cover and says to avoid wrapping the craft in plastic or non-breathable materials, which can cause mold.

This guide sets the three side by side on what matters over a winter: reuse, ventilation, access, installation, disposal and cost. Then it walks through the tools and steps for shrink wrapping as Dr. Shrink, a shrink-wrap supplier, publishes them, the risks of a tarp and how to size one, and what each option costs. Engine prep comes first: see our step-by-step guide to winterizing a jet ski, and if you're still deciding whether to cover the craft at all, do you need a jet ski cover.

Cover vs shrink wrap vs tarp at a glance

Each cell below names its source. BoatUS, the BoatUS Foundation and Discover Boating write about boats, and the makers write about their own craft, so read the table as what each source says, and check your owner's manual first.

Summarized from Yamaha, Sea-Doo (BRP), BoatUS, the BoatUS Foundation, Discover Boating, Dr. Shrink, West Marine and Ohio Sea Grant; see Sources. BoatUS and Discover Boating write about boats. Your owner's manual takes priority.
Fitted coverShrink wrapTarp
What the makers sayYamaha offers storage covers for WaveRunners (2021 guide); Sea-Doo's US page says to use a breathable, fitted coverMany Yamaha dealers offer shrink-wrapping (Yamaha, 2021); Sea-Doo's US page says to avoid wrapping the craft in plastic or non-breathable materials, which can cause moldSea-Doo's 2026 operator's guide: cover a craft stored outside with an opaque tarpaulin; its 2019 UK page: an opaque, breathable tarp
ReusabilityReusable: the BoatUS Foundation presents a reusable boat-storage cover as an alternative to shrinkwrappingOne season: Dr. Shrink's instructions describe removing and recycling the used wrap after the storage season; its heat gun kit is a one-time purchase that can be used year after year (West Marine listing)BoatUS (2021): plastic tarps typically begin to shred after the first blow; the BoatUS Foundation says a strong tarp might do for a budget-minded boater if installed well and checked regularly
Ventilation and condensationBoatUS Foundation: boats need to breathe while covered to avoid mildewing; its shopping tips ask, if a cover is tight, whether it includes ventsDr. Shrink: all shrink-wrap covers must be ventilated against moisture, condensation and mildew; BoatUS: it traps moisture and causes mildew if vents aren't used along its entire lengthSea-Doo (UK, 2019): an opaque, breathable tarp, and no plastic or other non-breathable material, which may cause mold
Access during storageBoatUS Foundation staff checked their covered test boats every other week through the winter to readjust covers and straps as necessaryThrough a zipper access door taped to the wrap after shrinking (Dr. Shrink listing at West Marine)The BoatUS Foundation describes marine-grade tarps as tied and/or weighted in place through grommets
InstallationBoatUS Foundation: its staff fitted each test cover from the bow, removing wrinkles while pulling it aft and cinching the side straps to pull out low spots; it suggests enlisting a helperSupport structure, strapping, film and a propane heat tool (Dr. Shrink); BoatUS: don't do it yourself, leave it to the prosBoatUS Foundation: a true DIY; Discover Boating: if it isn't supported and secured just right, leaks, rips and complete collapses are common
Disposal and recyclingKept for reuse; on fabrics, the BoatUS Foundation says polyester can be recycled, while acrylic can't through standard channelsDr. Shrink film is #4 low-density polyethylene, recyclable through its REBAG bags or a recycler that takes #4 LDPE (West Marine listing); Ohio Sea Grant says changing prices and logistics make recycling a challengeNo disposal guidance in the sources used here; the BoatUS Foundation describes marine-grade tarps as fiber-reinforced polyethylene
CostOurs: see the product page for the current price; boat-cover figures are in the price table belowDealer jet ski rates, and the BoatUS Foundation's per-foot figures for boats, are in the price table belowThe BoatUS Foundation's per-foot figure for a marine-grade tarp, for boats, is in the price table below

The sources don't agree on a winner, and most of them are writing about boats. Discover Boating, the consumer site of the National Marine Manufacturers Association (NMMA), calls a professional shrink-wrap job by far the best way to cover a boat for winter storage. The BoatUS Foundation, which tried nine covers on boats of 17 to 25 feet over the 2021-22 Maryland winter, concluded that no single option suits every boat, and found that good-quality semi-custom covers offered the best balance between fit, durability and value. For their own personal watercraft, Sea-Doo names an opaque tarpaulin or a breathable, fitted cover, and Yamaha names its storage covers alongside dealer shrink-wrapping.

Shrink wrap: the upsides and the downsides

Shrink wrap is plastic film laid over the craft, held by strapping and shrunk tight with a heat tool. Dr. Shrink's film is #4 low-density polyethylene, and West Marine's listing for it says that because the film is heat-tensioned, it eliminates pooling and sheds snow to reduce the risk of collapsing from snow loads, stays stable in high winds and won't chafe gelcoat and paint. BoatUS's 2021 winterizing guide agrees that shrink wrap is very effective at keeping rain and snow out.

The downsides, as the sources describe them:

  • Trapped moisture. BoatUS says shrink wrap will also trap moisture inside and create horrendous mildew problems if vents aren't used along the entire length of the cover. Dr. Shrink says every shrink-wrap cover must be ventilated to eliminate moisture, condensation and mildew during winter storage, and that it's better to install too many vents than too few.
  • Fire. BoatUS says not to shrink wrap a boat yourself: all it takes is a moment of inattention to ignite the wrap, and if the fire starts inside the cover, it might not be visible right away. It calls this a job best left to the pros.
  • One season. Dr. Shrink's instructions describe recycling the used wrap after the storage season, and West Marine's listing for Dr. Shrink's accessories kit calls its strapping, tape, vents and buckles materials most boaters need on a yearly basis.
  • Getting inside. To get inside a wrapped craft for mid-winter checks, Dr. Shrink sells zipper access doors, which are taped to the wrap after it's shrunk and allow access during the storage season.
  • Your maker's view. Sea-Doo's US winterizing page says to avoid wrapping the craft in plastic or non-breathable materials, which can cause mold, and its 2026 operator's guide says never to store the watercraft in a plastic bag. Yamaha's 2021 guide, by contrast, points owners to dealers that shrink wrap. Follow your own owner's manual, and ask the dealer how the wrap will be vented.

Two more practical points. If the craft will winter at a marina, read the contract: the BoatUS Foundation notes that some yards require shrink wrap for boats in rack storage, because the extra weight of pooled water on a cover could cause a collapse. And if you buy wrapping as a service, BoatUS's 2026 storage guide suggests asking about recyclable options.

Jet ski on a galvanized trailer in a driveway, its deck wrapped in white shrink-wrap film down to the rub rail, with a small square vent on the side

How to shrink wrap a jet ski: tools and materials

Dr. Shrink publishes installation instructions written for boats (the copy used here is a 2020 PDF) and sells its film and kits through marine retailers. Before you buy, weigh two warnings: BoatUS's advice is not to do the job yourself, and West Marine's listing for Dr. Shrink film says it is for professional use only. If you still plan to wrap your own ski, or want to know what a shop will use, this is what Dr. Shrink's instructions and kit listings call for.

Shrink-wrap kit, per Dr. Shrink

Roll of white shrink-wrap film, propane heat tool with hose, tape, strapping, knife, gloves, safety glasses and a fire extinguisher on a workbench

Important

Shrink wrap can catch fire

Dr. Shrink's instructions warn that its film can burn: if heat is applied incorrectly, the wrap can ignite into an open flame and drop onto other combustible material, starting a second fire. If you see the wrap on fire, it says to stop at once and inspect the area, and to keep a fire extinguisher available at all times. It also says to tape over the fuel vent before the film goes on. BoatUS adds that a fire inside the cover might not be visible right away, and calls shrink wrapping a job best left to the pros.

How much film, and how many vents

Dr. Shrink's method for a recreational boat: start at the highest point, the top of the support post, measure over the widest part of the boat to about 8 inches below the rub rail, double that figure and add 2 feet. It says the result is the narrowest roll width you can use. Its general venting chart gives boats up to 18 feet three vents, though its film-size tables list four for boats up to 16 feet, and it says it's better to over-ventilate than not to install enough. None of these figures is written for a jet ski, so if you're buying film for one, ask a shop that wraps personal watercraft.

Step by step: Dr. Shrink's wrapping sequence

The steps below follow Dr. Shrink's instructions, which are written for boats and refer to its training CD for the support structure and perimeter band; step 1 comes from Yamaha. Read the fire warning above before you start.

Shrink wrapping, in Dr. Shrink's order

  1. Step 1: Finish the storage prep and dry the craft

    Yamaha's 2021 guide lists "Wrap it up" after its oil-change, fogging, fuel and cleaning items in its list of key things to consider before storage, and says to make sure any item or area is bone-dry before closing it up or sealing it off. Winterize to your owner's manual before the wrap goes on.

  2. Step 2: Build the support structure

    Dr. Shrink says to install the support structure first, following the directions on its training CD. Its boat diagram calls for at least one support post for every 6 feet of length, and its 18-foot sample boat has the structure 12 inches above the highest point.

  3. Step 3: Prepare the craft

    Tape over the fuel vent; Dr. Shrink says to ask your dealer if you can't find it. Pad sharp objects with foam padding, shrink wrap or tape, and keep the film off the ground, because static in the film attracts dirt and dust that stop it welding properly.

  4. Step 4: Fit the film and the bands

    Once the film is on and heat-welded around the perimeter band, Dr. Shrink says to install the belly bands right away. These taut straps pull the slack out of the film so it tightens when heated.

  5. Step 5: Shrink from the bottom up

    Seal all pleats first, including at the bow and stern. Start heating at the bottom of the cover near one end, never in the middle, and move the heat tool as if spray painting toward the other end, up to the rub rail; Dr. Shrink says starting low lets the heat rise and speeds the job. Then shrink the top, keeping excess heat off corners and sharp protruding objects so the film keeps its full thickness there.

  6. Step 6: Do a hole patrol

    Check the finished cover for burn and puncture holes. Dr. Shrink says to repair them with shrink-wrap tape, rubbed to remove air bubbles and lightly warmed with the heat tool so it sticks better.

  7. Step 7: Untape the fuel vent

    Remove the tape you put over the fuel vent in step 3, as Dr. Shrink's instructions list next.

  8. Step 8: Add the vents and any door

    Dr. Shrink says vents and doors go on after the cover is completely shrunk and are not heated. Its vents are self-adhesive and need to be hand-warmed and rubbed to seal; a door is taped on with 2-inch or 4-inch shrink-wrap tape, then unzipped and the film cut away beneath it.

Tarps: what Sea-Doo says, and the risks

Sea-Doo names a tarp in its own storage advice. Its 2026 operator's guide says that if the watercraft is to be stored outside, cover it with an opaque tarpaulin to keep sun rays and grime from affecting the plastic components and finish, and to prevent dust from building up. Sea-Doo's 2019 UK winterizing page says to use an opaque, breathable tarp or a Sea-Doo cover, and not to wrap the craft in plastic or other non-breathable material, as it may cause mold in certain areas of the watercraft.

The risks, each as its source states it:

  • Wind. BoatUS's 2021 winterizing guide says plastic tarps typically will begin to shred after the first blow, leaving the boat unprotected, and that a few tarps stitched together with a spiderweb of lines end up shredded in the first serious storm.
  • Support. Discover Boating says the blue tarp method helps to protect a boat, but if the tarp isn't supported and secured just right, leaks, rips and complete collapses are common. In the BoatUS Foundation's test, the marine tarp was the only option that was a candidate for a frame, though one wasn't used.
  • Breathability. Sea-Doo's advice turns on the material: opaque, breathable on its UK page, and no plastic or non-breathable material. Whether a given tarp breathes isn't something the sources here test; the BoatUS Foundation describes marine-grade tarps as fiber-reinforced polyethylene.
  • Upkeep. The BoatUS Foundation's verdict is conditional: a strong tarp might do the trick for the budget-minded boater, if installed well and checked regularly.

Yamaha's footwell advice applies to covered craft too: it says even units with factory covers installed can collect water in the footwells when stored outdoors, and to check and drain them at least twice a month. For where a covered ski can spend the winter, see jet ski winter storage.

Jet ski on its trailer in a leafy backyard under a plain blue tarp tied to the trailer frame with light rope

What size tarp do you need for a jet ski?

Sea-Doo's guidance names an opaque tarpaulin but gives no size, so measure the craft and compare it with a tarp's finished size. Tarps and All, a tarp seller, says to measure a three-dimensional object's length front to back, its width side to side and its total height from the ground to the highest point, and to include all sides if the tarp has to wrap the object. On a jet ski, take three measurements:

  • Length: overall length, bow to stern. How to measure a jet ski for a cover shows where to hold the tape.
  • Width: across the widest point of the hull.
  • Height over the steering: run the tape from where the tarp will be tied off on one side, up and over the handlebars, and down to the tie-off point on the other side. That is how far the tarp has to reach across the craft.

Two sizing details from the same Tarps and All guide: a standard tarp's finished size, after hemming, is about 3 to 6 inches smaller than its cut size, and it suggests 4 to 8 inches of overlap for equipment covers. Check which size a seller lists before you buy.

Our covers don't need that arithmetic: both are sized by the craft's measured overall length. Measure bow to stern and match the number in the jet ski cover size guide.

Choosing a fitted cover instead

The third-party advice on covers is about covers in general, not about ours:

  • The BoatUS Foundation says boats need to breathe while covered to avoid mildewing, and its shopping tips ask, if a cover is tight, whether it includes vents.
  • Discover Boating separates storage covers, designed to fit loosely, from trailering covers, which have a snug fit and are reinforced in high-wear areas to withstand highway speeds.
  • Sea-Doo's US winterizing page says to cover the craft with a breathable, fitted cover and store it in a dry, ventilated place.
  • The BoatUS Foundation says to check a stored boat at least once a month and after snow or heavy rain, and Yamaha says to check and drain the footwells at least twice a month even on craft stored outdoors with factory covers installed.

Our Weatherproof Shield is the outdoor and trailering cover, sold as trailerable. It's made of water-resistant 600D solution-dyed polyester with a PU coating, and has an elastic hem cord, built-in buckles and straps, air vents to aid trailering, an extra strap set and a mesh storage bag. We don't make breathability or condensation claims for it, so the drying and checking advice above applies under it too. It comes in seven sizes, P0 to P6, by measured overall length, and has a Lifetime warranty; see the warranty page. The Satin Shield is an indoor cover only, for a garage or enclosed unit; a satin storage bag is included. Both are in our jet ski covers collection.

Trailerable Cover

AllGuard Weatherproof Shield Jet Ski Cover (Trailerable)

For a ski stored outdoors or trailered: water-resistant 600D PU-coated polyester, elastic hem cord, built-in buckles and straps, air vents to aid trailering. Seven sizes by overall length.

4 colors: Blue / Black, Gray / Black, Red / Black, Yellow / Black

  • Under 90 inP0
  • Under 102 inP1
  • Under 115 inP2
  • Under 125 inP3
  • Under 135 inP4
  • Under 145 inP5
  • Up to 160 inP6

Lifetime Warranty

Find your cover size

Both of our covers are sized by the craft's measured overall length. Measure bow to stern, then match the number in the size guide.

Open the size guide

What shrink wrap, tarps and covers cost

Shrink-wrap prices vary from shop to shop, so the table below sticks to published figures: three dealers' jet ski rates, the BoatUS Foundation's per-foot price comparison for boats, and retail prices for Dr. Shrink materials. Each is an example read on the date shown, not an average.

Published prices with the as-of date shown. The dealer and West Marine rows are single-seller examples, not averages or typical prices. The BoatUS Foundation figures are approximate per-foot price ranges for boats, gathered for its 2021-22 winter test of boats 17 to 25 feet long and published in September 2022. Prices change; ask for a current quote.
ItemSeller and locationPublished priceTermsSource and as-of date
Jet ski shrink wrap (service)Long Lake Marina, Naples, ME$275 single; $550 doubleListed under Shrink Wrap Only Rates as PWC Shrink Wrap Go HomeLong Lake Marina storage page, undated; read 2026-10-27
Jet ski shrink wrap with outdoor storageLong Lake Marina, Naples, ME$725 per unitListed under Storage Rates as PWC Shrink Wrap OutdoorLong Lake Marina storage page, undated; read 2026-10-27
Jet ski shrink wrap (service)Sportsmans Marina, Hewitt, NJ$372Listed as PWC Shrink Wrap with jet ski and jet boat winterization; the page says pricing may vary based on vessel size, condition and accessSportsmans Marina winterization page, undated; read 2026-10-27
Jet ski shrink wrap (service)Point Place Powersports, Toledo, OH$150Stated on its boat and jet ski winterization pagePoint Place Powersports winterization page, undated; read 2026-10-27
Boat shrink wrap (service)Shrinkwrapping services contacted by the BoatUS Foundation, MarylandAbout $15 to $28 per boat footBasic install only; boat figures, not jet ski ratesBoatUS Foundation, Foundation Findings #60, September 2022
Marine-grade tarpBoatUS Foundation price comparisonAbout $5 to $6 per boat footFiber-reinforced polyethylene with grommets; boat figuresBoatUS Foundation, Foundation Findings #60, September 2022
Generic boat coverBoatUS Foundation price comparisonAbout $9 to $17 per boat footOften sold by length and width; boat figures, not jet ski coversBoatUS Foundation, Foundation Findings #60, September 2022
Dr. Shrink film, 17 ft x 31 ft, 7-mil, whiteWest Marine (online listing)$102.99Shown in stock; the listing says the film is for professional use onlyWest Marine product page; read 2026-10-27
Dr. Shrink accessories kitWest Marine (online listing)$109.99Strapping, shrink-wrap tape, 4 self-adhesive vents and 10 buckles; no heat tool; shown in stockWest Marine product page; read 2026-10-27

Read the terms column before comparing rows. Long Lake Marina lists a wrap-only rate for a ski that goes home and a separate figure under its outdoor storage rates, and Sportsmans Marina says its pricing may vary with vessel size, condition and access. The retail rows don't include a heat tool, and Dr. Shrink's instructions call for a 20-pound propane tank as well. BoatUS lists shrink-wrapping among the extra services that can add to storage fees. For the rest of the winter bill, see how much it costs to winterize a jet ski and jet ski storage cost. The current price of our own cover is on its product page.

Cover, shrink wrap and tarp FAQ

The sources differ. Discover Boating calls a professional shrink-wrap job by far the best way to cover a boat for winter storage, and Yamaha's 2021 guide notes that many Yamaha dealers offer shrink-wrapping. The conditions matter: BoatUS says wrap without vents along its length traps moisture and causes mildew, and Sea-Doo says to avoid wrapping its craft in plastic or non-breathable materials. Check your owner's manual and ask how the wrap will be vented.

Sources

  1. Yamaha WaveRunners 2021 Maintenance Matters Guide (Storage & Care; Extended Storage: Wrap it up) (opens in a new tab)Yamaha Motor Corporation, USA · 2021
  2. GTI, GTR and Wake Series Operator's Guide 2026 (Storage, Protection, p. 169) (opens in a new tab)BRP (Sea-Doo) · 2026
  3. How to Winterize Your PWC (opens in a new tab)BRP (Sea-Doo) · 2026-06-09
  4. Winterizing your personal watercraft (UK) (opens in a new tab)BRP (Sea-Doo UK) · 2019-11-07 (published; page modified 2026-03-06)
  5. The Boater's Guide to Winterizing (To Cover Or Not To Cover) (opens in a new tab)BoatUS · 2021-09 (PDF date); retrieved 2026-10-27
  6. Winter Boat Storage Options: Indoor, Outdoor & In-Water (Frank Lanier) (opens in a new tab)BoatUS · October 2026 (page date)
  7. Boat Covers for Winter Storage (Foundation Findings #60) (opens in a new tab)BoatUS Foundation · 2022-09; retrieved 2026-10-27
  8. Boat Storage Guide (FAQ: how to wrap and cover a boat for winter storage) (opens in a new tab)Discover Boating (NMMA) · undated; retrieved 2026-10-27
  9. Boat Covers: How to Choose the Best Option (Storage Covers vs. Trailering Cover) (opens in a new tab)Discover Boating (NMMA) · undated; retrieved 2026-10-27
  10. Dr. Shrink Boat Maintenance & Winterization Installation Instructions (Tips for the Ultimate Shrink Wrap Job; Film Sizes & Venting) (PDF) (opens in a new tab)Dr. Shrink (PDF hosted on images.toolsid.com; file metadata lists BOATiD as author) · PDF dated 2020-01-29; retrieved 2026-10-27
  11. Dr. Shrink Shrink Wrap, 17 ft x 31 ft, 7mil, White (product listing) (opens in a new tab)West Marine · retrieved 2026-10-27
  12. Dr. Shrink Shrink Wrap Accessories Kit (product listing) (opens in a new tab)West Marine · retrieved 2026-10-27
  13. Dr. Shrink Zipper Access Doors (product listing) (opens in a new tab)West Marine · retrieved 2026-10-27
  14. Shrink Wrap Recycling for Ohio Marinas (opens in a new tab)Ohio Sea Grant (Ohio Clean Marinas Program) · undated; retrieved 2026-10-27
  15. Boat Storage Services: Pricing (Storage Rates; Shrink Wrap Only Rates) (opens in a new tab)Long Lake Marina, Naples, ME · undated; retrieved 2026-10-27
  16. Winterization: Winter Service Pricing (opens in a new tab)Sportsmans Marina, Hewitt, NJ · undated; retrieved 2026-10-27
  17. Boat & Jet Ski Winterization (opens in a new tab)Point Place Powersports, Toledo, OH · undated; retrieved 2026-10-27
  18. How to Choose the Right Custom Tarp Size: Step by Step Guide (opens in a new tab)Tarps and All · 2026-05-04

Find Your Size

Measure your jet ski bow to stern in a straight line, then enter the length in inches.

  1. Under 90 inP0
  2. Under 102 inP1
  3. Under 115 inP2
  4. Under 125 inP3
  5. Under 135 inP4
  6. Under 145 inP5
  7. Up to 160 inP6
Full Size Guide

In inches. Decimals are fine.

Covers for Your Jet Ski

All Covers